DTC P0882:00 [DJVA-EL]

id050212823100

DTC P0882:00

Battery back-up voltage low

DETECTION CONDITION

•  Condition: TCM communication normal while engine is idling

•  Status: Detects terminal B+ current of 9.05 V or less

•  Period: Confirmed 20 times continuously for 1 s or more

Diagnostic support note

•  The AT warning light does not illuminate.

•  PENDING CODE is not available.

•  The DTC is stored in the TCM memory.

POSSIBLE CAUSE

•  Melt down EGI 10A fuse

•  Melt down MAIN 200A fuse

•  EGI 10A fuse connector or terminal malfunction

•  EGI 200A fuse connector or terminal malfunction

•  Battery positive terminal malfunction

•  Battery malfunction

•  Short to GND in wiring harness between battery positive terminal and TCM terminal A24

•  TCM connector or terminal malfunction

•  Open circuit in wiring harness between battery positive terminal and TCM terminal A24

•  TCM malfunction

DTC P0882:00	Battery back-up voltage low
DETECTION CONDITION	• Condition: TCM communication normal while engine is idling • Status: Detects terminal B+ current of 9.05 V or less • Period: Confirmed 20 times continuously for 1 s or more Diagnostic support note • The AT warning light does not illuminate. • PENDING CODE is not available. • The DTC is stored in the TCM memory.
POSSIBLE CAUSE	• Melt down EGI 10A fuse • Melt down MAIN 200A fuse • EGI 10A fuse connector or terminal malfunction • EGI 200A fuse connector or terminal malfunction • Battery positive terminal malfunction • Battery malfunction • Short to GND in wiring harness between battery positive terminal and TCM terminal A24 • TCM connector or terminal malfunction • Open circuit in wiring harness between battery positive terminal and TCM terminal A24 • TCM malfunction

Diagnostic procedure

STEP	INSPECTION		ACTION
1	VERIFY RELATED REPAIR INFORMATION AVAILABILITY • Verify related service information availability. • Is any related repair information available?	Yes	Perform repair or diagnosis according to the available repair information. • If the vehicle is not repaired, go to the next step.
1		No	Go to the next step.
2	INSPECT EGI 10A FUSE • Switch the ignition to OFF. • Disconnect the negative battery cable. • Inspect the ENG +B 10A fuse for proper installation and failure. • Is it normal?	Yes	Go to the next step.
2		No	• If the fuse is not installed correctly, install it correctly, then go to Step 10. • If fuse has been melted, replace it, then go to Step 8.
3	INSPECT MAIN 200A FUSE • Switch the ignition to OFF. • Disconnect the negative battery cable. • Inspect the ENG +B 10A fuse for proper installation and failure. • Is it normal?	Yes	Go to the next step.
3		No	• If the fuse is not installed correctly, install it correctly, then go to Step 10. • If fuse has been melted, replace it, then go to Step 8.
4	INSPECT EGI 10A FUSE TERMINAL FOR POOR CONNECTION • Switch the ignition to OFF. • Inspect for poor connection (such as damaged, corrosion) • Is there any malfunction?	Yes	Repair or replace the terminal, then go to Step 8.
4		No	Go to the next step.
5	INSPECT MAIN 200A FUSE TERMINAL FOR POOR CONNECTION • Switch the ignition to OFF. • Inspect for poor connection (such as damaged, corrosion) • Is there any malfunction?	Yes	Repair or replace the terminal, then go to Step 8.
5		No	Go to the next step.
6	INSPECT BATTERY POSITIVE TERMINAL FOR POOR CONNECTION • Switch the ignition to OFF. • Inspect for poor connection (such as damaged, corrosion) • Is there any malfunction?	Yes	Repair or replace the terminal, then go to Step 8.
6		No	Go to the next step.
7	INSPECT BATTERY POSITIVE CIRCUIT FOR SHORT TO GND • Switch the ignition to OFF. • Disconnect the battery positive terminal. • Inspect for continuity between the battery positive terminal (wiring harness-side) and body GND. • Is there continuity?	Yes	Repair or replace the wiring harness for a possible short to GND, then go to Step 8.
7		No	Go to the next step.
8	INSPECT TCM CONNECTOR FOR POOR CONNECTION • Switch the ignition to OFF. • Disconnect the TCM connector. • Inspect for poor connection (such as damaged/pulled-out pins, corrosion) • Is there any malfunction?	Yes	Repair or replace the terminal, then go to Step 8.
8		No	Go to the next step.
9	INSPECT BATTERY POSITIVE CIRCUIT FOR OPEN CIRCUIT • Switch the ignition to OFF. • Disconnect the battery positive terminal. • Inspect for continuity between battery positive terminal (wiring harness-side) and TCM terminal A24 (wiring harness-side). • Is there continuity?	Yes	Go to the next step.
9		No	Repair or replace the wiring harness for a possible open circuit, then go to the next step.
10	VERIFY TROUBLESHOOTING OF DTC P0882:00 COMPLETED • Make sure to reconnect all the disconnected connectors. • Clear the DTC using the M-MDS. • Perform the following procedure to ensure that the DTC has been resolved: 1. Start the engine. 2. Idle the engine for 120 s or more. • Is the same DTC present?	Yes	Perform the following procedure, then go to next step. 1. Replace the TCM. (See TCM REMOVAL/INSTALLATION [DJVA-EL].) 2. Perform TCM learning. (See TCM LEARNING [DJVA-EL].)
10		No	Go to the next step.
11	VERIFY NO DTC HAS BEEN PRESENTED • Perform the “Reading DTCs Procedure”. (See ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [DJVA-EL].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See ON-BOARD DIAGNOSTIC SYSTEM DTC TABLE [DJVA-EL].)
11		No	DTC troubleshooting completed.