DRIVER-SIDE DOOR GLASS CAN BE OPERATED MANUALLY BUT CANNOT BE OPERATED AUTOMATICALLY [POWER WINDOW SYSTEM]

id0903a0069800

Outline

Description

•  Driver-side door glass can be operated manually but cannot be operated automatically.

Possible cause

•  Door glass is manually opened/closed10 times without fully closing it

•  Power window main switch malfunction

•  Door-electrical supply unit (driver's side) malfunction

Diagnostic Procedure

Step

Inspection

Results

Action

1

VERIFY ALL SYSTEM DTCs

•  Perform the DTC inspection.
(See DTC INSPECTION.)

•  Are any DTCs displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

No

Go to the next step.

2

PERFORM POWER WINDOW SYSTEM INITIAL SETTING

•  Perform the power window system initial setting.
(See POWER WINDOW SYSTEM INITIALIZATION PROCEDURE.)

•  Has the malfunction symptom been eliminated?

Yes

Complete the symptom troubleshooting. (Explain contents of repair to customer)

No

Go to the next step.

3

INSPECT POWER WINDOW MAIN SWITCH FOR MALFUNCTION

•  Inspect the applicable part.
(See POWER WINDOW MAIN SWITCH INSPECTION [(E)].)

•  Is the part normal?

Yes

Go to the next step.

No

Repair or replace the malfunctioning location and perform the repair completion verification.

(See POWER WINDOW MAIN SWITCH REMOVAL/INSTALLATION.)

Repair completion verification

VERIFY THAT VEHICLE IS REPAIRED

•  Install/connect the part removed/disconnected during the troubleshooting procedure.

•  Has the malfunction symptom been eliminated?

Yes

Complete the symptom troubleshooting. (Explain contents of repair to customer)

No

Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].)

If the CAN communication is normal, perform the diagnosis from Step 1.

•  If the malfunction is not resolved, replace the door-electrical supply unit (driver's side).
(See DOOR-ELECTRICAL SUPPLY UNIT REMOVAL/INSTALLATION.)

Description	• Driver-side door glass can be operated manually but cannot be operated automatically.
Possible cause	• Door glass is manually opened/closed10 times without fully closing it • Power window main switch malfunction • Door-electrical supply unit (driver's side) malfunction

Step	Inspection	Results	Action
1	VERIFY ALL SYSTEM DTCs • Perform the DTC inspection. (See DTC INSPECTION.) • Are any DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
1		No	Go to the next step.
2	PERFORM POWER WINDOW SYSTEM INITIAL SETTING • Perform the power window system initial setting. (See POWER WINDOW SYSTEM INITIALIZATION PROCEDURE.) • Has the malfunction symptom been eliminated?	Yes	Complete the symptom troubleshooting. (Explain contents of repair to customer)
2		No	Go to the next step.
3	INSPECT POWER WINDOW MAIN SWITCH FOR MALFUNCTION • Inspect the applicable part. (See POWER WINDOW MAIN SWITCH INSPECTION [(E)].) • Is the part normal?	Yes	Go to the next step.
3		No	Repair or replace the malfunctioning location and perform the repair completion verification. (See POWER WINDOW MAIN SWITCH REMOVAL/INSTALLATION.)
Repair completion verification	VERIFY THAT VEHICLE IS REPAIRED • Install/connect the part removed/disconnected during the troubleshooting procedure. • Has the malfunction symptom been eliminated?	Yes	Complete the symptom troubleshooting. (Explain contents of repair to customer)
Repair completion verification		No	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].) If the CAN communication is normal, perform the diagnosis from Step 1. • If the malfunction is not resolved, replace the door-electrical supply unit (driver's side). (See DOOR-ELECTRICAL SUPPLY UNIT REMOVAL/INSTALLATION.)