DTC B10DF:46/C0082:47/C0082:48/C0082:49/U2007:46 [DYNAMIC STABILITY CONTROL (DSC)]

id0402b2888200

Note
•  Only vehicles with combined sensor.
Applied VIN (assumed):
European (L.H.D. U.K.) specs.
•  JMZ BL12F60# 100001—181415
•  JMZ BL12F70# 100001—181415
•  JMZ BL12Y20# 100001—181415
•  JMZ BL12Z20# 100001—181415
•  JMZ BL12Z50# 100001—181415
•  JMZ BL14F60# 100001—181415
•  JMZ BL14F70# 100001—181415
•  JMZ BL14Y20# 100001—181415
•  JMZ BL14Z20# 100001—181415
•  JMZ BL14Z50# 100001—181415
•  JMZ BLA2A60# 100001—181415
•  JMZ BLA2C60# 100001—181415
•  JMZ BLA2F70# 100001—181415
•  JMZ BLA2G60# 100001—181415
•  JMZ BLA2Y60# 100001—181415
•  JMZ BLA2Z20# 100001—181415
•  JMZ BLA2Z50# 100001—181415
•  JMZ BLA4360# 100001—181415
•  JMZ BLA4A60# 100001—181415
•  JMZ BLA4C60# 100001—181415
•  JMZ BLA4F70# 100001—181415
•  JMZ BLA4G60# 100001—181415
•  JMZ BLA4Y60# 100001—181415
•  JMZ BLA4Z20# 100001—181415
•  JMZ BLA4Z50# 100001—181415
Australian specs.
•  JM0 BL103100 100001—225632
•  JM0 BL10C100 100001—225632
•  JM0 BL10F100 100001—225632
•  JM0 BL10L100 100001—225632
General (R.H.D.) specs.
•  JM6 BL1031*0 100001—225632
•  JM6 BL1051*0 100001—225632
•  JM6 BL10F1*0 100001—225632
•  JM6 BL10L1*0 100001—225632
•  JM6 BL10Z1*0 100001—225632
General (L.H.D.) specs., Arab Gulf Cooperation Council, China
•  JM7 BL04F**# 100001—225632
•  JM7 BL04Z**# 100001—225632
•  JM7 BL12F**# 100001—225632
•  JM7 BL12Z**# 100001—225632
•  JM7 BL14F**# 100001—225632
•  JM7 BL14Z**# 100001—225632
•  JM7 BL22F**# 100001—225632
•  JM7 BL22Z**# 100001—225632
•  JM7 BL24F**# 100001—225632
•  JM7 BL24Z**# 100001—225632

DTC
B10DF:46, C0082:47, C0082:48, C0082:49, U2007:46
DSC HU/CM (internal malfunction)
DETECTION CONDITION
•  The DSC CM on-board diagnostic function detects control module internal malfunction.
POSSIBLE CAUSE
•  DSC HU/CM internal malfunction

Diagnostic procedure

STEP

INSPECTION

ACTION
1
VERIFY NO DSC HU/CM MALFUNCTION
•  Clear the DTCs from the memory.
•  Start the engine and drive the vehicle at 10km/h {6.2 mph} or more.
•  Are the same DTCs present?
Yes
Replace the DSC HU/CM, then go to the next step.
(See DSC HU/CM REMOVAL/INSTALLATION.)
No
Go to the next step.
2
VERIFY THAT NO OTHER DTCS ARE PRESENT
•  Are any other DTCs output?
Yes
Go to the applicable DTC inspection.
(See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].)
No
DTC troubleshooting completed.