ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)]

id0402b2800200


On-Board Diagnostic (OBD) Test Description

•  The OBD test inspects the integrity and function of the DSC and outputs the results when requested by the specific tests.
•  On-board diagnostic test also:
―  Provides a quick inspection of the DSC usually performed at the start of each diagnostic procedure.
―  Provides verification after repairs to ensure that no other faults occurred during service.
•  The OBD test is divided into 3 tests:
―  Read/clear diagnostic results, PID monitor and record and active command modes.

Read/clear diagnostic results

•  This function allows you to read or clear DTCs in the DSC HU/CM memory.


PID/Data monitor and record

•  This function allows you to access certain data values, input signals, calculated values, and system status information.


Active command modes

•  This function allows you to control devices through the M-MDS.


Reading DTCs Procedure

1.  Connect the M-MDS to the DLC-2.

am3zzn00002365

2.  After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

•  When using the IDS (laptop PC)
1.  Select “Self Test”.
2.  Select “Modules”.
3.  Select “ABS”.
•  When using the PDS (Pocket PC)
1.  Select “Module Tests”.
2.  Select “ABS”.
3.  Select “Self Test”.

3.  Verify the DTC according to the directions on the screen.

•  If any DTCs are displayed, perform troubleshooting according to the corresponding DTC inspection.

4.  After completion of repairs, clear all DTCs stored in the DSC. (See Clearing DTCs Procedures.)


Clearing DTCs Procedures

1.  Connect the M-MDS to the DLC-2.

am3zzn00002365

2.  After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

•  When using the IDS (laptop PC)
1.  Select “Self Test”.
2.  Select “Modules”.
3.  Select “ABS”.
•  When using the PDS (Pocket PC)
1.  Select “Module Tests”.
2.  Select “ABS”.
3.  Select “Self Test”.

3.  Verify the DTC according to the directions on the screen.

4.  Press the clear button on the DTC screen to clear the DTC.

5.  Switch the ignition to off.

6.  Switch the ignition to ON and wait for 5 s or more.

7.  Perform DTC inspection. (See Reading DTCs Procedure.)

8.  Verify that no DTCs are displayed.


PID/Data Monitor and Record Procedure

1.  Connect the M-MDS to the DLC-2.

am3zzn00002365

2.  After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

•  When using the IDS (laptop PC)
1.  Select “DataLogger”.
2.  Select “Modules”.
3.  Select “ABS”.
•  When using the PDS (Pocket PC)
1.  Select “Module Tests”.
2.  Select “ABS”.
3.  Select “DataLogger”.

3.  Select the applicable PID from the PID table.

4.  Verify the PID data according to the directions on the screen.

Note
•  The PID data screen function is used for monitoring the calculated value of input/output signals in the module.Therefore, if the monitored value of the output parts is not within the specification, it is necessary to inspect the monitored value of input parts corresponding to the applicable output part control. In addition, because the system does not display an output part malfunction as an abnormality in the monitored value, it is necessary to inspect the output parts individually.
•  When detecting DTCs, PIDs related to a malfunctioning system may not display even if the module is normal. Therefore, if a PID is not displayed, it is necessary to verify the DTC, perform malfunction diagnosis of the DTC that was detected, and do repairs.

Active Command Modes Procedure

1.  Connect the M-MDS to the DLC-2.

am3zzn00002365

2.  After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

•  When using the IDS (laptop PC)
1.  Select “DataLogger”.
2.  Select “Modules”.
3.  Select “ABS”.
•  When using the PDS (Pocket PC)
1.  Select “Module Tests”.
2.  Select “ABS”.
3.  Select “DataLogger”.

3.  Select the active command modes from the PID table.

4.  Perform the active command modes, inspect the operations for each parts.

•  If the operation of output parts cannot be verified after the active command mode inspection is performed, this could indicate the possibility of an open or short circuit, sticking, or operation malfunction in the output parts.


DTC Table

Note
•  Vehicles with combined sensor: Applied VIN (assumed)
European (L.H.D. U.K.) specs.
•  JMZ BL12F60# 100001—181415
•  JMZ BL12F70# 100001—181415
•  JMZ BL12Y20# 100001—181415
•  JMZ BL12Z20# 100001—181415
•  JMZ BL12Z50# 100001—181415
•  JMZ BL14F60# 100001—181415
•  JMZ BL14F70# 100001—181415
•  JMZ BL14Y20# 100001—181415
•  JMZ BL14Z20# 100001—181415
•  JMZ BL14Z50# 100001—181415
•  JMZ BLA2A60# 100001—181415
•  JMZ BLA2C60# 100001—181415
•  JMZ BLA2F70# 100001—181415
•  JMZ BLA2G60# 100001—181415
•  JMZ BLA2Y60# 100001—181415
•  JMZ BLA2Z20# 100001—181415
•  JMZ BLA2Z50# 100001—181415
•  JMZ BLA4360# 100001—181415
•  JMZ BLA4A60# 100001—181415
•  JMZ BLA4C60# 100001—181415
•  JMZ BLA4F70# 100001—181415
•  JMZ BLA4G60# 100001—181415
•  JMZ BLA4Y60# 100001—181415
•  JMZ BLA4Z20# 100001—181415
•  JMZ BLA4Z50# 100001—181415
Australian specs.
•  JM0 BL103100 100001—225632
•  JM0 BL10C100 100001—225632
•  JM0 BL10F100 100001—225632
•  JM0 BL10L100 100001—225632
General (R.H.D.) specs.
•  JM6 BL1031*0 100001—225632
•  JM6 BL1051*0 100001—225632
•  JM6 BL10F1*0 100001—225632
•  JM6 BL10L1*0 100001—225632
•  JM6 BL10Z1*0 100001—225632
General (L.H.D.) specs., Arab Gulf Cooperation Council, China
•  JM7 BL04F**# 100001—225632
•  JM7 BL04Z**# 100001—225632
•  JM7 BL12F**# 100001—225632
•  JM7 BL12Z**# 100001—225632
•  JM7 BL14F**# 100001—225632
•  JM7 BL14Z**# 100001—225632
•  JM7 BL22F**# 100001—225632
•  JM7 BL22Z**# 100001—225632
•  JM7 BL24F**# 100001—225632
•  JM7 BL24Z**# 100001—225632
•  Vehicles without combined sensor: Applied VIN (assumed)
European (L.H.D. U.K.) specs.
•  JMZ BL12F60# 181416—
•  JMZ BL12F70# 181416—
•  JMZ BL12Y20# 181416—
•  JMZ BL12Z20# 181416—
•  JMZ BL12Z50# 181416—
•  JMZ BL14F60# 181416—
•  JMZ BL14F70# 181416—
•  JMZ BL14Y20# 181416—
•  JMZ BL14Z20# 181416—
•  JMZ BL14Z50# 181416—
•  JMZ BLA2A60# 181416—
•  JMZ BLA2C60# 181416—
•  JMZ BLA2F70# 181416—
•  JMZ BLA2G60# 181416—
•  JMZ BLA2Y60# 181416—
•  JMZ BLA2Z20# 181416—
•  JMZ BLA2Z50# 181416—
•  JMZ BLA4360# 181416—
•  JMZ BLA4A60# 181416—
•  JMZ BLA4C60# 181416—
•  JMZ BLA4F70# 181416—
•  JMZ BLA4G60# 181416—
•  JMZ BLA4Y60# 181416—
•  JMZ BLA4Z20# 181416—
•  JMZ BLA4Z50# 181416—
Australian specs.
•  JM0 BL103100 225633—
•  JM0 BL10C100 225633—
•  JM0 BL10F100 225633—
•  JM0 BL10L100 225633—
General (R.H.D.) specs.
•  JM6 BL1031*0 225633—
•  JM6 BL1051*0 225633—
•  JM6 BL10F1*0 225633—
•  JM6 BL10L1*0 225633—
•  JM6 BL10Z1*0 225633—
General (L.H.D.) specs., Arab Gulf Cooperation Council, China
•  JM7 BL04F**# 225633—
•  JM7 BL04Z**# 225633—
•  JM7 BL12F**# 225633—
•  JM7 BL12Z**# 225633—
•  JM7 BL14F**# 225633—
•  JM7 BL14Z**# 225633—
•  JM7 BL22F**# 225633—
•  JM7 BL22Z**# 225633—
•  JM7 BL24F**# 225633—
•  JM7 BL24Z**# 225633—

DTC

System malfunction location

Page

M-MDS
B10DF:46
DSC HU/CM (internal malfunction)
Vehicles with combined sensor
(See DTC B10DF:46/C0082:47/C0082:48/C0082:49/U2007:46 [DYNAMIC STABILITY CONTROL (DSC)].)
Vehicles without combined sensor
(See DTC B10DF:46/C0082:47/C0082:48/C0082:49/C1B14:01/U2007:46 [DYNAMIC STABILITY CONTROL (DSC)].)
C0001:01
DSC HU/CM internal malfunction (traction control solenoid valve system)
(See DTC C0001:01/C0002:01/C0003:01/C0004:01/C0010:01/C0011:01/C0014:01/C0015:01/C0018:01/C0019:01/C001C:01/C001D:01 [DYNAMIC STABILITY CONTROL (DSC)].)
C0002:01
C0003:01
DSC HU/CM internal malfunction (stability control solenoid valve system)
C0004:01
C0010:01
DSC HU/CM internal malfunction (LF inlet solenoid)
(See DTC C0001:01/C0002:01/C0003:01/C0004:01/C0010:01/C0011:01/C0014:01/C0015:01/C0018:01/C0019:01/C001C:01/C001D:01 [DYNAMIC STABILITY CONTROL (DSC)].)
C0011:01
DSC HU/CM internal malfunction (LF outlet solenoid)
C0014:01
DSC HU/CM internal malfunction (RF inlet solenoid)
C0015:01
DSC HU/CM internal malfunction (RF outlet solenoid)
C0018:01
DSC HU/CM internal malfunction (LR inlet solenoid)
C0019:01
DSC HU/CM internal malfunction (LR outlet solenoid)
C001C:01
DSC HU/CM internal malfunction (RR inlet solenoid)
C001D:01
DSC HU/CM internal malfunction (RR outlet solenoid)
C0020:01
Pump motor, motor relay
(See DTC C0020:01/C0020:1C/C0020:71 [DYNAMIC STABILITY CONTROL (DSC)].)
C0020:1C
Pump motor, motor relay
C0020:71
Pump motor, motor relay
C0030:07
LF ABS sensor rotor
(See DTC C0030:07/C0031:07/C0033:07/C0034:07/C0036:07/C0037:07/C0039:07/C003A:07 [DYNAMIC STABILITY CONTROL (DSC)].)
C0031:01
LF ABS wheel-speed sensor
(See DTC C0031:01/C0034:01/C0037:01/C003A:01 [DYNAMIC STABILITY CONTROL (DSC)].)
C0031:07
LF ABS wheel-speed sensor/ABS sensor rotor
(See DTC C0030:07/C0031:07/C0033:07/C0034:07/C0036:07/C0037:07/C0039:07/C003A:07 [DYNAMIC STABILITY CONTROL (DSC)].)
C0033:07
RF ABS sensor rotor
C0034:01
RF ABS wheel-speed sensor
(See DTC C0031:01/C0034:01/C0037:01/C003A:01 [DYNAMIC STABILITY CONTROL (DSC)].)
C0034:07
RF ABS wheel-speed sensor/ABS sensor rotor
(See DTC C0030:07/C0031:07/C0033:07/C0034:07/C0036:07/C0037:07/C0039:07/C003A:07 [DYNAMIC STABILITY CONTROL (DSC)].)
C0036:07
LR ABS sensor rotor
C0037:01
LR ABS wheel-speed sensor
(See DTC C0031:01/C0034:01/C0037:01/C003A:01 [DYNAMIC STABILITY CONTROL (DSC)].)
C0037:07
LR ABS wheel-speed sensor/ABS sensor rotor
(See DTC C0030:07/C0031:07/C0033:07/C0034:07/C0036:07/C0037:07/C0039:07/C003A:07 [DYNAMIC STABILITY CONTROL (DSC)].)
C0039:07
RR ABS sensor rotor
C003A:01
RR ABS wheel-speed sensor
(See DTC C0031:01/C0034:01/C0037:01/C003A:01 [DYNAMIC STABILITY CONTROL (DSC)].)
C003A:07
RR ABS wheel-speed sensor/ABS sensor rotor
(See DTC C0030:07/C0031:07/C0033:07/C0034:07/C0036:07/C0037:07/C0039:07/C003A:07 [DYNAMIC STABILITY CONTROL (DSC)].)
C0040:64
Brake switch
(See DTC C0040:64 (Z6, LF, MZR 2.0 DISI i-stop, L3 Turbo, L5) [DYNAMIC STABILITY CONTROL (DSC)].)
(See DTC C0040:64 (MZ-CD 1.6 (Y6)) [DYNAMIC STABILITY CONTROL (DSC)].)
(See DTC C0040:64 (MZR-CD 2.2) [DYNAMIC STABILITY CONTROL (DSC)].)
C0044:01
Brake fluid pressure sensor
(See DTC C0044:01/C0044:28/C0044:54/C0044:64 [DYNAMIC STABILITY CONTROL (DSC)].)
C0044:28
Brake fluid pressure sensor
C0044:54
Brake fluid pressure sensor
C0044:64
Brake fluid pressure sensor
C0051:28
Steering angle sensor
(See DTC C0051:28 [DYNAMIC STABILITY CONTROL (DSC)].)
C0061:01*1
Combined sensor system
Vehicles with combined sensor
(See DTC C0061:01/C0061:28/C0061:64/C0063:01/C0063:28/C0063:64/C006A:01/C006A:16/C006A:17 [DYNAMIC STABILITY CONTROL (DSC)].)
Vehicles without combined sensor
(See DTC C0061:28/C0061:64/C0063:28/C0063:64 [DYNAMIC STABILITY CONTROL (DSC)].)
C0061:28
Combined sensor system (vehicles with combined sensor)
SAS control module system (vehicles without combined sensor)
C0061:54
DSC HU/CM system (unperformed initialization procedure)
(See DTC C0061:54/C0063:54 [DYNAMIC STABILITY CONTROL (DSC)].)
C0061:64
Combined sensor system (vehicles with combined sensor)
SAS control module system (vehicles without combined sensor)
Vehicles with combined sensor
(See DTC C0061:01/C0061:28/C0061:64/C0063:01/C0063:28/C0063:64/C006A:01/C006A:16/C006A:17 [DYNAMIC STABILITY CONTROL (DSC)].)
Vehicles without combined sensor
(See DTC C0061:28/C0061:64/C0063:28/C0063:64 [DYNAMIC STABILITY CONTROL (DSC)].)
C0063:01*1
Combined sensor system
C0063:28
Combined sensor system (vehicles with combined sensor)
SAS control module system (vehicles without combined sensor)
C0063:54
DSC HU/CM system (unperformed initialization procedure)
(See DTC C0061:54/C0063:54 [DYNAMIC STABILITY CONTROL (DSC)].)
C0063:64
Combined sensor system
(See DTC C0061:01/C0061:28/C0061:64/C0063:01/C0063:28/C0063:64/C006A:01/C006A:16/C006A:17 [DYNAMIC STABILITY CONTROL (DSC)].)
C006A:01*1
Combined sensor system
C006A:04*1
Combined sensor (internal malfunction)
(See DTC C006A:04/C006A:47 [DYNAMIC STABILITY CONTROL (DSC)].)
C006A:16*1
Combined sensor system
(See DTC C0061:01/C0061:28/C0061:64/C0063:01/C0063:28/C0063:64/C006A:01/C006A:16/C006A:17 [DYNAMIC STABILITY CONTROL (DSC)].)
C006A:17*1
Combined sensor system
C006A:47*1
Combined sensor (internal malfunction)
(See DTC C006A:04/C006A:47 [DYNAMIC STABILITY CONTROL (DSC)].)
C006A:95*1
Combined sensor mismatched installation
(See DTC C006A:95 [DYNAMIC STABILITY CONTROL (DSC)].)
C006B:00
TCS/DSC control system
(See DTC C006B:00/C0072:68 [DYNAMIC STABILITY CONTROL (DSC)].)
C0072:68
TCS/DSC control system
C0082:47
DSC HU/CM (internal malfunction)
Vehicles with combined sensor
(See DTC B10DF:46/C0082:47/C0082:48/C0082:49/U2007:46 [DYNAMIC STABILITY CONTROL (DSC)].)
Vehicles without combined sensor
(See DTC B10DF:46/C0082:47/C0082:48/C0082:49/C1B14:01/U2007:46 [DYNAMIC STABILITY CONTROL (DSC)].)
C0082:48
DSC HU/CM (internal malfunction)
C0082:49
DSC HU/CM (internal malfunction)
C1109:64
DSC OFF switch
(See DTC C1109:64 [DYNAMIC STABILITY CONTROL (DSC)].)
C1B14:01*2
DSC HU/CM (internal malfunction)
(See DTC B10DF:46/C0082:47/C0082:48/C0082:49/C1B14:01/U2007:46 [DYNAMIC STABILITY CONTROL (DSC)].)
U0001:88
CAN line
(See DTC U0001:88/U0100:00/U0101:00/U0140:00/U0155:00 [DYNAMIC STABILITY CONTROL (DSC)].)
U0100:00
CAN line
U0101:00*3
CAN line
U0125:00*1
Combined sensor system (CAN2 line malfunction)
(See DTC U0125:00/U0125:88 [DYNAMIC STABILITY CONTROL (DSC)].)
U0125:88*1
Combined sensor system (CAN2 line malfunction)
U0140:00
CAN line
(See DTC U0001:88/U0100:00/U0101:00/U0140:00/U0155:00 [DYNAMIC STABILITY CONTROL (DSC)].)
U0151:00*2
SAS control module system (CAN2 line malfunction)
(See DTC U0151:00 [DYNAMIC STABILITY CONTROL (DSC)].)
U0155:00
CAN line
(See DTC U0001:88/U0100:00/U0101:00/U0140:00/U0155:00 [DYNAMIC STABILITY CONTROL (DSC)].)
U0401:00
Abnormal message from PCM
(See DTC U0401:00 [DYNAMIC STABILITY CONTROL (DSC)].)
U0402:00
Abnormal message from PCM (MTX, ATX (FN4A-EL))
Abnormal message from TCM (ATX (FS5A-EL))
(See DTC U0402:00 [DYNAMIC STABILITY CONTROL (DSC)].)
U0422:00
Abnormal message from BCM
(See DTC U0422:00/U0428:62/U0428:64 [DYNAMIC STABILITY CONTROL (DSC)].)
U0428:62
Abnormal message from BCM
U0428:64
Abnormal message from BCM
U0452:86*2
Abnormal message from SAS control module
(See DTC U0452:86 [DYNAMIC STABILITY CONTROL (DSC)].)
U2007:46
DSC HU/CM (internal malfunction)
Vehicles with combined sensor
(See DTC B10DF:46/C0082:47/C0082:48/C0082:49/U2007:46 [DYNAMIC STABILITY CONTROL (DSC)].)
Vehicles without combined sensor
(See DTC B10DF:46/C0082:47/C0082:48/C0082:49/C1B14:01/U2007:46 [DYNAMIC STABILITY CONTROL (DSC)].)
U2100:00
DSC HU/CM configuration
(See DTC U2100:00/U2101:00 [DYNAMIC STABILITY CONTROL (DSC)].)
U2101:00
DSC HU/CM configuration
U3003:08
Power supply system
(See DTC U3003:08/U3003:16/U3003:17 [DYNAMIC STABILITY CONTROL (DSC)].)
U3003:16
Power supply system
U3003:17
Power supply system

*1  :Vehicles with combined sensor
*2  :Vehicles without combined sensor
*3  :ATX (FS5A-EL)

PID/DATA Monitor Table

PID name (definition)

Unit/Condition

Operation condition (reference)

Action

DSC HU/CM terminal
BRAKE_SW
Off/On
•  Brake pedal released: Off
•  Brake pedal depressed: On
Inspect the brake switch.
(See BRAKE SWITCH INSPECTION.)
—
DSC_ST
Off/On
•  DSC not operating: Off
•  DSC operating: On
Inspect the DSC HU/CM.
(See DSC HU/CM INSPECTION.)
—
DSC_SW
Off/On
•  DSC OFF switch is released: Off
•  DSC OFF switch is depressed: On
Inspect the DSC OFF switch.
(See DSC OFF SWITCH INSPECTION.)
AK
EX_TEMP
°C, °F
•  Ambient temperature
—
—
LAT_ACCL
G
•  Vehicle stopped or driving at constant speed: 0 G
•  Cornering to right: Changes 0 G—positive
•  Cornering to left: Changes 0 G—negative
Inspect the combined sensor. (Vehicles with combined sensor)
(See COMBINED SENSOR INSPECTION.)
Perform the DTC inspection for the SAS control module. (Vehicles without combined sensor)
(See DTC INSPECTION [TYPE B].)
—
MCYLI_P
Pa, psi
•  Brake pedal depressed: Changes according to the brake fluid pressure
Inspect the brake fluid pressure sensor.
(See BRAKE FLUID PRESSURE SENSOR INSPECTION.)
—
PMP_MTR
Off/On
•  Pump motor not activated: Off
•  Pump motor activated: On
Inspect the DSC HU/CM.
(See DSC HU/CM INSPECTION.)
—
STEER_ANGL
°
•  Steering wheel in neutral position (not turned): 0°
•  Steering wheel turned to left: Changes 0°—negative
•  Steering wheel turned to right: Changes 0°—positive
Inspect the steering angle sensor.
(See STEERING ANGLE SENSOR INSPECTION.)
—
VSPD
KPH, MPH
•  Vehicle stopped: 0 KPH, 0 MPH
•  Vehicle running: Vehicle speed
Inspect the DSC HU/CM.
(See DSC HU/CM INSPECTION.)
Inspect the ABS wheel-speed sensor.
(See FRONT ABS WHEEL-SPEED SENSOR INSPECTION.)
(See REAR ABS WHEEL-SPEED SENSOR INSPECTION.)
—
VPWR
V
•  Switch the ignition to ON: Approx. 12.2 V
•  Idling: Approx. 14.1 V
Inspect power supply circuit.
(See DSC HU/CM INSPECTION.)
Y
V_LF_INL
Off/On
•  Solenoid valve not activated: Off
•  Solenoid valve activated: On
Inspect the DSC HU/CM.
(See DSC HU/CM INSPECTION.)
—
V_LF_OTL
V_LR_INL
V_LR_OTL
V_RF_INL
V_RF_OTL
V_RR_INL
V_RR_OTL
V_STB_L
Off/On
•  Solenoid valve activated: On
•  Solenoid valve not activated: Off
Inspect the DSC HU/CM.
(See DSC HU/CM INSPECTION.)
—
V_STB_R
V_TRC_L
Off/On
•  Solenoid valve activated: On
•  Solenoid valve not activated: Off
Inspect the DSC HU/CM.
(See DSC HU/CM INSPECTION.)
—
V_TRC_R
WSPD_LF
KPH, MPH
•  Vehicle stopped: 0 KPH, 0 MPH
•  Vehicle running: Vehicle speed
Inspect the front ABS wheel-speed sensor.
(See FRONT ABS WHEEL-SPEED SENSOR INSPECTION.)
F, I
WSPD_LR
Inspect the rear ABS wheel-speed sensor.
(See REAR ABS WHEEL-SPEED SENSOR INSPECTION.)
AG, AJ
WSPD_RF
Inspect the front ABS wheel-speed sensor.
(See FRONT ABS WHEEL-SPEED SENSOR INSPECTION.)
AP, AS
WSPD_RR
Inspect the rear ABS wheel-speed sensor.
(See REAR ABS WHEEL-SPEED SENSOR INSPECTION.)
O, R
YAW_RATE
°/s
•  Vehicle stopped or driving straight: 0 °/s
•  Cornering to left: Changes 0 °/s—negative
•  Cornering to right: Changes 0 °/s—positive
Inspect the combined sensor. (Vehicles with combined sensor)
(See COMBINED SENSOR INSPECTION.)
Perform the DTC inspection for the SAS control module. (Vehicles without combined sensor)
(See DTC INSPECTION [TYPE B].)
—


Active Command Modes Table

Command name

Output part

Operation

Operating condition
PMP_MTR
Pump motor
Off/On
Switch the ignition to ON
V_LF_INL
LF inlet solenoid valve
V_LF_OTL
LF outlet solenoid valve
V_LR_INL
LR inlet solenoid valve
V_LR_OTL
LR outlet solenoid valve
V_RF_INL
RF inlet solenoid valve
V_RF_OTL
RF outlet solenoid valve
V_RR_INL
RR inlet solenoid valve
V_RR_OTL
RR outlet solenoid valve
V_STB_L
Left stability control solenoid valve
V_STB_R
Right stability control solenoid valve
V_TRC_L
Left traction control solenoid valve
V_TRC_R
Right traction control solenoid valve