DTC P0108:00 [SKYACTIV-G 2.0]

id0102h1701200

DTC P0108:00

MAP sensor circuit high input

DETECTION CONDITION

•  The PCM monitors the input voltage from the MAP sensor. If the input voltage at the PCM terminal 1BW is above 4.89 V for 5 s, the PCM determines that the MAP sensor circuit has a malfunction.

Diagnostic support note

•  This is a continuous monitor (CCM).

•  The MIL illuminates if the PCM detects the above malfunction condition during the first drive cycle.

•  FREEZE FRAME DATA (Mode 2)/Snapshot data is available.

•  The DTC is stored in the PCM memory.

FAIL-SAFE FUNCTION

•  Estimates MAP using MAF sensor and engine speed.

•  Restricts the upper limit of the engine speed.

•  Inhibits the evaporative purge control.

POSSIBLE CAUSE

•  MAP sensor/IAT sensor No.2 connector or terminals malfunction

•  PCM connector or terminals malfunction

•  MAP sensor malfunction

•  Short to power supply in wiring harness between MAP sensor/IAT sensor No.2 terminal D and PCM terminal 1BW

•  Open circuit in wiring harness between the following terminals:

―  MAP sensor/IAT sensor No.2 terminal D—PCM terminal 1BW

―  MAP sensor/IAT sensor No.2 terminal A—PCM terminal 1BX

―  MAP sensor/IAT sensor No.2 terminal C—PCM terminal 1BO

•  PCM malfunction

DTC P0108:00	MAP sensor circuit high input
DETECTION CONDITION	• The PCM monitors the input voltage from the MAP sensor. If the input voltage at the PCM terminal 1BW is above 4.89 V for 5 s, the PCM determines that the MAP sensor circuit has a malfunction. Diagnostic support note • This is a continuous monitor (CCM). • The MIL illuminates if the PCM detects the above malfunction condition during the first drive cycle. • FREEZE FRAME DATA (Mode 2)/Snapshot data is available. • The DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION	• Estimates MAP using MAF sensor and engine speed. • Restricts the upper limit of the engine speed. • Inhibits the evaporative purge control.
POSSIBLE CAUSE	• MAP sensor/IAT sensor No.2 connector or terminals malfunction • PCM connector or terminals malfunction • MAP sensor malfunction • Short to power supply in wiring harness between MAP sensor/IAT sensor No.2 terminal D and PCM terminal 1BW • Open circuit in wiring harness between the following terminals: ― MAP sensor/IAT sensor No.2 terminal D—PCM terminal 1BW ― MAP sensor/IAT sensor No.2 terminal A—PCM terminal 1BX ― MAP sensor/IAT sensor No.2 terminal C—PCM terminal 1BO • PCM malfunction

Diagnostic Procedure

STEP	INSPECTION		ACTION
1	VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA HAS BEEN RECORDED • Has the FREEZE FRAME DATA (Mode 2)/snapshot data been recorded?	Yes	Go to the next step.
1		No	Record the FREEZE FRAME DATA (Mode 2)/snapshot data on the repair order, then go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	CLASSIFY MAP SENSOR MALFUNCTION OR WIRING HARNESS MALFUNCTION • Access the MAP PID using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-G 2.0].) • Verify the MAP PID value. • Is the MAP PID value 5 V or B+?	Yes	When the voltage is 5V • Go to Step 7. When the voltage is B+ • Go to Step 8.
3		No	Go to the next step.
4	INSPECT MAP SENSOR/IAT SENSOR NO.2 CONNECTOR CONDITION • Switch the ignition to off. • Disconnect the MAP sensor/IAT sensor No.2 connector. • Inspect for poor connection (such as damaged/pulled-out pins, corrosion). • Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 9.
4		No	Go to the next step.
5	INSPECT PCM CONNECTOR CONDITION • Disconnect the PCM connector. • Inspect for poor connection (such as damaged/pulled-out pins, corrosion). • Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 9.
5		No	Go to the next step.
6	INSPECT MAP SENSOR • Reconnect all disconnected connectors. • Inspect the MAP sensor. (See MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR INSPECTION [SKYACTIV-G 2.0].) • Is there any malfunction?	Yes	Replace the MAP sensor/IAT sensor No.2, then go to Step 9. (See MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR/INTAKE AIR TEMPERATURE (IAT) SENSOR NO.2 REMOVAL/INSTALLATION [SKYACTIV-G 2.0].)
6		No	Go to Step 9.
7	INSPECT MAP SENSOR/IAT SENSOR NO.2 CIRCUIT FOR OPEN CIRCUIT • Switch the ignition to off. • Disconnect the MAP sensor/IAT sensor No.2 connector and PCM connector. • Inspect for continuity between the following terminals (wiring harness-side): ― MAP sensor/IAT sensor No.2 terminal D—PCM terminal 1BW ― MAP sensor/IAT sensor No.2 terminal A—PCM terminal 1BX ― MAP sensor/IAT sensor No.2 terminal C—PCM terminal 1BO • Is there continuity?	Yes	Replace the MAP sensor/IAT sensor No.2, then go to Step 9. (See MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR/INTAKE AIR TEMPERATURE (IAT) SENSOR NO.2 REMOVAL/INSTALLATION [SKYACTIV-G 2.0].)
7		No	Repair or replace the wiring harness for a possible open circuit, then go to Step 9.
8	INSPECT MAP SENSOR/IAT SENSOR NO.2 CIRCUIT FOR SHORT TO POWER SUPPLY • Switch the ignition to off. • Disconnect the MAP sensor/IAT sensor No.2 connector and PCM connector. • Measure the voltage at the MAP sensor/IAT sensor No.2 terminal D (wiring harness-side). • Is there any voltage?	Yes	Repair or replace the wiring harness for a possible short to power supply, then go to the next step.
8		No	Replace the MAP sensor/IAT sensor No.2, then go to the next step. (See MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR/INTAKE AIR TEMPERATURE (IAT) SENSOR NO.2 REMOVAL/INSTALLATION [SKYACTIV-G 2.0].)
9	VERIFY DTC TROUBLESHOOTING COMPLETED • Make sure to reconnect all disconnected connectors. • Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE [SKYACTIV-G 2.0].) • Start the engine and warm it up completely. • Perform the KOEO or KOER self test. (See KOEO/KOER SELF TEST [SKYACTIV-G 2.0].) • Is the same DTC present?	Yes	Repeat the inspection from Step 1. • If the malfunction recurs, replace the PCM. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.0].) Go to the next step.
9		No	Go to the next step.
10	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [SKYACTIV-G 2.0].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [SKYACTIV-G 2.0].)
10		No	DTC troubleshooting completed.