NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [MZR 2.0 DISI i-stop]

id011736800800

Warning

• Before removing the SRS air bag system-related parts, always disconnect the negative battery cable and wait for 1 min. or more to allow the back-up power supply to deplete its stored power. (See AIR BAG SYSTEM SERVICE WARNINGS.)

Required procedure after negative battery cable disconnection/connection

System name

Conditions after disconnecting the negative battery cable

Required procedure

Reference

Before disconnecting negative battery cable

After connecting negative battery cable

Power window system

Reset to initial setting and auto-function is disabled.

—

Perform the power window system initial setting.

(See POWER WINDOW SYSTEM INITIALIZATION PROCEDURE.)

Clock and audio

Clock display and audio system memory are reset.

Verify the setting content.

Set the verified content before disconnecting negative battery cable.

—

i-stop system

If main battery is disconnected, specific information stored in PCM is erased.

—

Perform “Procedure after Reconnecting Negative Battery Cable”.

(See BATTERY REMOVAL/INSTALLATION [MZR 2.0 DISI i-stop].)

Steering angle sensor initialization

AFS control module

Reset to initial setting and the system may not operate properly.

—

Perform steering angle sensor initialization.

(See STEERING ANGLE SENSOR INITIALIZATION PROCEDURE.)

System name	Conditions after disconnecting the negative battery cable	Required procedure	Reference
Power window system	Reset to initial setting and auto-function is disabled.	—	Perform the power window system initial setting.	(See POWER WINDOW SYSTEM INITIALIZATION PROCEDURE.)
Clock and audio	Clock display and audio system memory are reset.	Verify the setting content.	Set the verified content before disconnecting negative battery cable.	—
i-stop system	If main battery is disconnected, specific information stored in PCM is erased.	—	Perform “Procedure after Reconnecting Negative Battery Cable”.	(See BATTERY REMOVAL/INSTALLATION [MZR 2.0 DISI i-stop].)
Steering angle sensor initialization	AFS control module	Reset to initial setting and the system may not operate properly.	—	Perform steering angle sensor initialization.	(See STEERING ANGLE SENSOR INITIALIZATION PROCEDURE.)

Negative Battery Cable Disconnection

1. Switch the ignition to off.

2. Remove the Battery cover.(See BATTERY REMOVAL/INSTALLATION [MZR 2.0 DISI i-stop].)

3. Disconnect the negative battery cable.

Negative Battery Cable Connection

Caution

• Verifying the tightness while holding the current sensor may apply excessive force to the terminal and the terminal could loosen, causing poor engine starting. When verifying the tightness of the negative battery cable, only hold the terminal area, not the current sensor.

• When tightening the negative battery cable, tighten it to the specified torque. If it is not tightened to the specified torque, the battery charging/discharging may be affected.

1. Connect the negative battery cable.(See BATTERY REMOVAL/INSTALLATION [MZR 2.0 DISI i-stop].)

2. Perform services which are required after connecting the negative battery cable. (See Required procedure after negative battery cable disconnection/connection.)

System name		Conditions after disconnecting the negative battery cable	Required procedure		Reference
System name		Conditions after disconnecting the negative battery cable	Before disconnecting negative battery cable	After connecting negative battery cable	Reference
Power window system		Reset to initial setting and auto-function is disabled.	—	Perform the power window system initial setting.	(See POWER WINDOW SYSTEM INITIALIZATION PROCEDURE.)
Clock and audio		Clock display and audio system memory are reset.	Verify the setting content.	Set the verified content before disconnecting negative battery cable.	—
i-stop system		If main battery is disconnected, specific information stored in PCM is erased.	—	Perform “Procedure after Reconnecting Negative Battery Cable”.	(See BATTERY REMOVAL/INSTALLATION [MZR 2.0 DISI i-stop].)
Steering angle sensor initialization	AFS control module	Reset to initial setting and the system may not operate properly.	—	Perform steering angle sensor initialization.	(See STEERING ANGLE SENSOR INITIALIZATION PROCEDURE.)