PERSONALIZATION FEATURES

id120000000000

Note

• Settings of some personalization features displayed on the M-MDS cannot be switched depending on the vehicle specification.

• The following systems can be personalized.

• When performing a personalization setting, refer to the referenced section for the detailed setting procedure.

Glass/Windows/Mirrors

Rear window defogger

Personalization features

Setting contents

Setting procedure

Rear window defogger operation time can be changed.

15 minutes/Continuous

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
Rear window defogger operation time can be changed.	15 minutes/Continuous	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Security And Locks

Advanced keyless entry system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The advanced keyless entry system and push button start system functions can be disabled.

Enabled. / Disabled.

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

The out-of-area (reception area) type auto lock function can be set.

Not Adopted. / OFF / ON

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

Off / On

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The operation start time of the auto re-lock function can be changed.

Not Adopted. / 30 seconds / 60 seconds / 90 seconds

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

30 seconds / 60 seconds / 90 seconds

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The keyless beeper volume can be adjusted.

Not Adopted. / Off / Low / Medium / High

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Medium / Low / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the door lock system to the initial setting.

No / Yes

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The advanced keyless entry system and push button start system functions can be disabled.	Enabled. / Disabled.	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
The out-of-area (reception area) type auto lock function can be set.	Not Adopted. / OFF / ON	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
Off / On	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation start time of the auto re-lock function can be changed.	Not Adopted. / 30 seconds / 60 seconds / 90 seconds	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
30 seconds / 60 seconds / 90 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The keyless beeper volume can be adjusted.	Not Adopted. / Off / Low / Medium / High	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
High / Medium / Low / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the door lock system to the initial setting.	No / Yes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Keyless entry system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The keyless entry system and push button start system functions can be disabled.

Enabled. / Disabled.

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

The operation start time of the auto re-lock function can be changed.

Not Adopted. / 30 seconds / 60 seconds / 90 seconds

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

30 seconds / 60 seconds / 90 seconds

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the door lock system to the initial setting.

No / Yes

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The keyless entry system and push button start system functions can be disabled.	Enabled. / Disabled.	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation start time of the auto re-lock function can be changed.	Not Adopted. / 30 seconds / 60 seconds / 90 seconds	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
30 seconds / 60 seconds / 90 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the door lock system to the initial setting.	No / Yes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Lighting Systems

Auto light system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

Auto light sensor sensitivity can be changed.

Not Adopted./Dark/Medium Dark/Medium/Medium Light/Light

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Light/Medium Light/ Medium/Medium Dark/Dark

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

No / Yes

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
Auto light sensor sensitivity can be changed.	Not Adopted./Dark/Medium Dark/Medium/Medium Light/Light	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
Light/Medium Light/ Medium/Medium Dark/Dark	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	No / Yes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Running Light System (Australian Specs.)

Personalization features

Setting contents

Setting procedure

The running light system function can be set.

Off (Running light non-illumination) / On (Running light illumination)

(See LIGHTING SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

No / Yes

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The running light system function can be set.	Off (Running light non-illumination) / On (Running light illumination)	(See LIGHTING SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	No / Yes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Turn light system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The turn light system can be switched between operable and inoperable.

Not Adopted./OFF/ON

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

No / Yes

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The turn light system can be switched between operable and inoperable.	Not Adopted./OFF/ON	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	No / Yes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Coming home light system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The coming home light system operation time can be switched.

Not Adopted./0 seconds./30 seconds./60 seconds./90 seconds./120 seconds.

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Off / 30 seconds / 60 seconds / 90 seconds / 120 seconds

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

No / Yes

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The coming home light system operation time can be switched.	Not Adopted./0 seconds./30 seconds./60 seconds./90 seconds./120 seconds.	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
Off / 30 seconds / 60 seconds / 90 seconds / 120 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	No / Yes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Leaving home light system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The leaving home light system can be switched between operable and inoperable.

Not Adopted./Off/On

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

No / Yes

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The leaving home light system can be switched between operable and inoperable.	Not Adopted./Off/On	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	No / Yes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Room light control system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

• The front/rear map light illumination time after any door is opened can be changed.

• The trunk compartment light (4SD)/cargo compartment light (5HB) illumination time after the trunk lid (4SD)/liftgate (5HB) is opened can be changed.

Not Adopted./30 minutes./60 minutes./10 minutes.

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

60 minutes / 30 minutes / 10 minutes

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The front/rear map light illumination time after all the doors are closed can be changed.

Not Adopted./7.5 seconds./15 seconds./30 seconds./60 seconds.

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

60 seconds / 30 seconds / 15 seconds / 7.5 seconds

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

No / Yes

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
• The front/rear map light illumination time after any door is opened can be changed. • The trunk compartment light (4SD)/cargo compartment light (5HB) illumination time after the trunk lid (4SD)/liftgate (5HB) is opened can be changed.	Not Adopted./30 minutes./60 minutes./10 minutes.	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
60 minutes / 30 minutes / 10 minutes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The front/rear map light illumination time after all the doors are closed can be changed.	Not Adopted./7.5 seconds./15 seconds./30 seconds./60 seconds.	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
60 seconds / 30 seconds / 15 seconds / 7.5 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	No / Yes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Auto Light-Off System

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The headlight emitted time of the auto light off timer can be changed.

Not Adopted./0 seconds./30 seconds./60 seconds./90 seconds./120 seconds.

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

120 seconds / 90 seconds / 60 seconds / 30 seconds / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The headlight emitted time of the auto light off timer can be changed.	Not Adopted./0 seconds./30 seconds./60 seconds./90 seconds./120 seconds.	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
120 seconds / 90 seconds / 60 seconds / 30 seconds / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

High Beam Control (HBC) System

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The high beam control (HBC) system can be switched between operable and inoperable.

Not Adopted./OFF/ON

M-MDS is used.

(See FORWARD SENSING CAMERA (FSC) PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

No / Yes

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The high beam control (HBC) system can be switched between operable and inoperable.	Not Adopted./OFF/ON	M-MDS is used. (See FORWARD SENSING CAMERA (FSC) PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	No / Yes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Wiper/Washer System

Auto wiper system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The auto wiper function can be disabled.

Not Adopted. / Off^*1 (Intermittent) / On (Rain Sensing)

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off^*1

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The auto wiper function can be disabled.	Not Adopted. / Off^*1 (Intermittent) / On (Rain Sensing)	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off^*1	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :If the function is set to “Off”, the wipers will operate intermittently with the wiper switch in AUTO position.

Instrumentation/Driver Info.

Temperature

Personalization features

Setting contents

Setting procedure

The temperature unit can be changed.^*1

°F /°C^*2

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The temperature unit can be changed.^*1	°F /°C^*2	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :When the ambient temperature display is switched, the set A/C cabin temperature display is also changed.

*2 :The initial value differs depending on the market.

Distance

Personalization features

Setting contents

Setting procedure

The distance unit can be changed.

Miles / Km*1

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The distance unit can be changed.	Miles / Km*1	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :The initial value differs depending on the market.

Language

Personalization features	Setting contents	Setting procedure
The display language can be changed.	English/French/German/Italian/Spanish/Russian/Portuguese/Dutch/Swedish/Danish/Norwegian/Finnish/Czech/Slovakian/Hungarian/Turkish/Polish/Estonian/Latvian/Lithuanian/Greek/Croatian/Bulgarian/Romanian/Serbian/Hebrew	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Turn And Hazard Indicator Alarm

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The volume of the turn and hazard indicator alarm can be changed.

Not Adopted. / Low / High

M-MDS is used.

(See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Low

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The volume of the turn and hazard indicator alarm can be changed.	Not Adopted. / Low / High	M-MDS is used. (See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)
High / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Lights-on Reminder Warning Alarm

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The volume for the lights-on reminder warning alarm can be changed.

Not Adopted. / OFF^*1 / Low / High

M-MDS is used.

(See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Low / Off^*1

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The volume for the lights-on reminder warning alarm can be changed.	Not Adopted. / OFF^*1 / Low / High	M-MDS is used. (See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)
High / Low / Off^*1	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :The setting of the lights-on reminder can be changed with the time setting of auto light off system set to Off.

Intelligent Drive Master (i-DM)

Note

• There are two types of personalization procedures; one using the instrument cluster and the other using the center display.

Personalization features

Setting contents

Setting procedure

Display/non-display of the Intelligent Drive Master (i-DM) screen can be switched.

ON / OFF^*1

Instrument cluster is used for the setting.

(See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

ON / OFF

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Display/non-display of the Intelligent Drive Master (i-DM) ending screen can be switched.

ON / OFF

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The number of stages the Intelligent Drive Master (i-DM) can be switched.

St 3 / St 5

Instrument cluster is used for the setting.

(See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
Display/non-display of the Intelligent Drive Master (i-DM) screen can be switched.	ON / OFF^*1	Instrument cluster is used for the setting. (See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)
ON / OFF	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Display/non-display of the Intelligent Drive Master (i-DM) ending screen can be switched.	ON / OFF	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The number of stages the Intelligent Drive Master (i-DM) can be switched.	St 3 / St 5	Instrument cluster is used for the setting. (See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :Without center display

Rear Vehicle Monitoring (RVM) System

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The volume of the rear vehicle monitoring (RVM) warning alarm can be changed.

Not Adopted. / OFF / Low / High

M-MDS is used.

(See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Low / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The volume of the rear vehicle monitoring (RVM) warning alarm can be changed.	Not Adopted. / OFF / Low / High	M-MDS is used. (See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)
High / Low / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Blind Spot Monitoring (BSM) System

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The volume of the blind spot monitoring (BSM) warning alarm can be changed.

Not Adopted. / OFF / Low / High

M-MDS is used.

(See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Low / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The volume of the blind spot monitoring (BSM) warning alarm can be changed.	Not Adopted. / OFF / Low / High	M-MDS is used. (See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)
High / Low / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Lane Departure Warning System (LDWS)

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The volume of the LDWS warning alarm can be changed.

Not Adopted./Volume 1/Volume 2/Volume 3

M-MDS is used.

(See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

The volume of the LDWS warning alarm (Rumble) can be changed.

High / Medium / Low

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The volume of the LDWS warning alarm (Beep) can be changed.

High / Low

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The type of the LDWS warning alarm can be changed.

Beep / Rumble

M-MDS is used.

(See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

Beep / Rumble

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The distance between the warning-trigger lines for the Lane Departure Warning System (LDWS) and vehicle lanes can be changed.

Not Adopted / Adaptive / Early / Medium / Late

M-MDS is used.

(See FORWARD SENSING CAMERA (FSC) PERSONALIZATION FEATURES SETTING PROCEDURE.)

Adaptive / Early / Medium / Late

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The warning operation sensitivity of the lane departure warning system (LDWS) can be changed.

Not Adopted. / Often / Medium / Rare

M-MDS is used.

(See FORWARD SENSING CAMERA (FSC) PERSONALIZATION FEATURES SETTING PROCEDURE.)

Often / Medium / Rare

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lane departure warning system to the initial setting.

No / Yes

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The volume of the LDWS warning alarm can be changed.	Not Adopted./Volume 1/Volume 2/Volume 3	M-MDS is used. (See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)
The volume of the LDWS warning alarm (Rumble) can be changed.	High / Medium / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The volume of the LDWS warning alarm (Beep) can be changed.	High / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The type of the LDWS warning alarm can be changed.	Beep / Rumble	M-MDS is used. (See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)
Beep / Rumble	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The distance between the warning-trigger lines for the Lane Departure Warning System (LDWS) and vehicle lanes can be changed.	Not Adopted / Adaptive / Early / Medium / Late	M-MDS is used. (See FORWARD SENSING CAMERA (FSC) PERSONALIZATION FEATURES SETTING PROCEDURE.)
Adaptive / Early / Medium / Late	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The warning operation sensitivity of the lane departure warning system (LDWS) can be changed.	Not Adopted. / Often / Medium / Rare	M-MDS is used. (See FORWARD SENSING CAMERA (FSC) PERSONALIZATION FEATURES SETTING PROCEDURE.)
Often / Medium / Rare	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lane departure warning system to the initial setting.	No / Yes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Distance Recognition Support System (DRSS)

Personalization features

Setting contents

Setting procedure

The operation of distance recognition support system (DRSS) can be turned off.

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The operation distance for the alert function can be changed.

Long / Middle / Short

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the distance recognition support system (DRSS) to the initial setting.

No / Yes

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The operation of distance recognition support system (DRSS) can be turned off.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation distance for the alert function can be changed.	Long / Middle / Short	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the distance recognition support system (DRSS) to the initial setting.	No / Yes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Smart City Brake Support (SCBS)

Personalization features

Setting contents

Setting procedure

The operation of smart city brake support (SCBS) can be turned off.

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The operation of smart city brake support (SCBS) can be turned off.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Smart Brake Support (SBS)

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The operation of Smart Brake Support (SBS) can be turned off.

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The detection range of Smart Brake Support (SBS) system can be changed.^*1

Near / Far

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The volume of the Smart Brake Support (SBS) warning alarm can be changed.

Not Adopted. / OFF / Low / High

M-MDS is used.

(See FORWARD SENSING CAMERA (FSC) PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Low / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the smart brake support (SBS) to the initial setting.

No / Yes

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The operation of Smart Brake Support (SBS) can be turned off.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The detection range of Smart Brake Support (SBS) system can be changed.^*1	Near / Far	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The volume of the Smart Brake Support (SBS) warning alarm can be changed.	Not Adopted. / OFF / Low / High	M-MDS is used. (See FORWARD SENSING CAMERA (FSC) PERSONALIZATION FEATURES SETTING PROCEDURE.)
High / Low / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the smart brake support (SBS) to the initial setting.	No / Yes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :Australian Specs. (These specs cannot change the detection range of Smart Brake Support (SBS) system.)