DTC P0404:00 [MZR-CD 2.2]
id0102f3155300
DTC P0404:00 |
EGR control circuit range/performance problem |
---|---|
DETECTION CONDITION
|
• The PCM monitors the EGR valve control signal current to calculate EGR valve (DC motor) temperature. If the calculate malfunction when the EGR valve (DC motor) temperature is more than 90 °C {194 °F}, the PCM determines that the EGR valve control circuit has a malfunction.
MONITORING CONDITIONS
Diagnostic support note
• The MIL illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM.
• PENDING CODE is available if the PCM detects the above malfunction condition during first drive cycle.
• FREEZE FRAME DATA (Mode 2)/Snapshot data is available.
• The DTC is stored in the PCM memory.
|
POSSIBLE CAUSE
|
• EGR valve connector or terminals malfunction
• EGR valve malfunction
• PCM connector or terminals malfunction
• PCM malfunction
|
Diagnostic procedure
STEP |
INSPECTION |
ACTION |
|
---|---|---|---|
1
|
IDENTIFY TRIGGER DTC FOR FREEZE FRAME DATA (MODE 2)
• Perform the Freeze Frame PID Data Access Procedure.
• Is the DTC P0404:00 on FREEZE FRAME DATA (Mode 2)?
|
Yes
|
Go to the next step.
|
No
|
Go to the troubleshooting procedure for DTC on FREEZE FRAME DATA (Mode 2).
(See DTC TABLE [MZR-CD 2.2].)
|
||
2
|
VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA HAS BEEN RECORDED
• Has the FREEZE FRAME DATA (Mode 2)/snapshot data been recorded?
|
Yes
|
Go to the next step.
|
No
|
Record the FREEZE FRAME DATA (Mode 2)/snapshot data on the repair order, then go to the next step.
|
||
3
|
VERIFY RELATED SERVICE INFORMATION AVAILABILITY
• Verify related Service Information availability.
• Is any related Service Information available?
|
Yes
|
Perform repair or diagnosis according to the available Service Information.
• If the vehicle is not repaired, go to the next step.
|
No
|
Go to the next step.
|
||
4
|
INSPECT EGR VALVE CONNECTOR CONDITION
• Switch the ignition to off.
• Disconnect the EGR valve connector.
• Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
• Is there any malfunction?
|
Yes
|
Repair or replace the connector and/or terminals, then go to Step 7.
|
No
|
Go to the next step.
|
||
5
|
INSPECT EGR VALVE
• Inspect the EGR valve.
• Is there any malfunction?
|
Yes
|
Replace the EGR valve, then go to Step 7.
|
No
|
Go to the next step.
|
||
6
|
INSPECT PCM CONNECTOR CONDITION
• Disconnect the PCM connector.
• Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
• Is there any malfunction?
|
Yes
|
Repair or replace the connector and/or terminals, then go to the next step.
|
No
|
Go to the next step.
|
||
7
|
VERIFY DTC TROUBLESHOOTING COMPLETED
• Make sure to reconnect all disconnected connectors.
• Clear the DTC from the PCM memory using the M-MDS.
• Start the engine.
• Perform the KOEO or KOER self test.
• Is the PENDING CODE for this DTC present?
|
Yes
|
Replace the PCM, then go to the next step.
|
No
|
Go to the next step.
|
||
8
|
VERIFY AFTER REPAIR PROCEDURE
• Perform the “AFTER REPAIR PROCEDURE”.
• Are any DTCs present?
|
Yes
|
Go to the applicable DTC inspection.
(See DTC TABLE [MZR-CD 2.2].)
|
No
|
DTC troubleshooting completed.
|