DTC P0605:00 [PCM (SKYACTIV-D 2.2)]

id0102j5156400

DTC P0605:00

PCM memory check sum error

DETECTION CONDITION

•  Error in PCM internal memory is detected 2 times continuously.

Diagnostic support note

•  This is a continuous monitor (CCM).

•  The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle.

•  FREEZE FRAME DATA/Snapshot data is available.

•  DTC is stored in the PCM memory.

FAIL-SAFE FUNCTION

•  Limits the engine torque/limits the maximum engine speed.

•  Inhibits the EGR control.

•  Inhibits the diesel particulate filter regeneration control.

•  Inhibits the intake shutter valve control.

•  Stops the G-vectoring control (GVC).

•  Inhibits engine-stop by i-stop control.

•  Limits the engine transaxle total control.

POSSIBLE CAUSE

•  PCM connector or terminal malfunction

•  PCM malfunction

―  PCM internal memory error

SYSTEM WIRING DIAGRAM

Not applicable

DTC P0605:00	PCM memory check sum error
DETECTION CONDITION	• Error in PCM internal memory is detected 2 times continuously. Diagnostic support note • This is a continuous monitor (CCM). • The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle. • FREEZE FRAME DATA/Snapshot data is available. • DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION	• Limits the engine torque/limits the maximum engine speed. • Inhibits the EGR control. • Inhibits the diesel particulate filter regeneration control. • Inhibits the intake shutter valve control. • Stops the G-vectoring control (GVC). • Inhibits engine-stop by i-stop control. • Limits the engine transaxle total control.
POSSIBLE CAUSE	• PCM connector or terminal malfunction • PCM malfunction ― PCM internal memory error
SYSTEM WIRING DIAGRAM	Not applicable

Diagnostic Procedure

Step

Inspection

Results

Action

1

RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION

Note

•  Recording can be facilitated using the screen capture function of the PC.

•  Record the freeze frame data/snap shot data.

—

Go to the next step.

2

INSPECT PCM CONNECTOR CONDITION

•  Switch the ignition OFF.

•  Disconnect the PCM connector.

•  Inspect the connector engagement and connection condition, and inspect the terminals for damage, deformation, corrosion, or disconnection.

•  Is the connector normal?

Yes

Go to the next step.

No

Repair or replace the connector, then go to the next step.

3

VERIFY THAT REPAIRS HAVE BEEN COMPLETED

•  Reconnect all the disconnected connectors.

•  Refer to the [MEMORY CLEARING PROCEDURE] and clear the DTC.
(See CLEARING DTC [PCM (SKYACTIV-D 2.2)].)

•  Switch the ignition ON (engine off).

•  Switch the ignition OFF and wait for 30 s.

•  Display the DTCs using the M-MDS.
(See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-D 2.2)].)

•  Has DTC P0605:00 been recorded?

Yes

Replace the PCM, then go to the next step.

(See PCM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

No

Go to the next step.

4

VERIFY OTHER DTCs

•  Has any other DTC or pending code been stored?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

(See DTC TABLE [PCM (SKYACTIV-D 2.2)].)

No

DTC troubleshooting completed.

Step	Inspection	Results	Action
1	RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION Note • Recording can be facilitated using the screen capture function of the PC. • Record the freeze frame data/snap shot data.	—	Go to the next step.
2	INSPECT PCM CONNECTOR CONDITION • Switch the ignition OFF. • Disconnect the PCM connector. • Inspect the connector engagement and connection condition, and inspect the terminals for damage, deformation, corrosion, or disconnection. • Is the connector normal?	Yes	Go to the next step.
2		No	Repair or replace the connector, then go to the next step.
3	VERIFY THAT REPAIRS HAVE BEEN COMPLETED • Reconnect all the disconnected connectors. • Refer to the [MEMORY CLEARING PROCEDURE] and clear the DTC. (See CLEARING DTC [PCM (SKYACTIV-D 2.2)].) • Switch the ignition ON (engine off). • Switch the ignition OFF and wait for 30 s. • Display the DTCs using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-D 2.2)].) • Has DTC P0605:00 been recorded?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)
3		No	Go to the next step.
4	VERIFY OTHER DTCs • Has any other DTC or pending code been stored?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [PCM (SKYACTIV-D 2.2)].)
4		No	DTC troubleshooting completed.