DTC P0610:00 [PCM (SKYACTIV-D 2.2)]

id0102j5706000

DTC P0610:00

PCM vehicle configuration error

DETECTION CONDITION

•  With the following conditions met, the vehicle recognition is not correctly stored in the PCM for a continuous 1 s.

―  Ignition is switched ON (engine off or on)

Diagnostic support note

•  This is a continuous monitor (CCM).

•  The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle.

•  FREEZE FRAME DATA/Snapshot data is available.

•  DTC is stored in the PCM memory.

FAIL-SAFE FUNCTION

•  Inhibits engine-stop by i-stop control.

POSSIBLE CAUSE

•  PCM configuration has not been correctly performed

•  PCM connector or terminal malfunction

•  PCM malfunction

SYSTEM WIRING DIAGRAM

Not applicable

DTC P0610:00	PCM vehicle configuration error
DETECTION CONDITION	• With the following conditions met, the vehicle recognition is not correctly stored in the PCM for a continuous 1 s. ― Ignition is switched ON (engine off or on) Diagnostic support note • This is a continuous monitor (CCM). • The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle. • FREEZE FRAME DATA/Snapshot data is available. • DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION	• Inhibits engine-stop by i-stop control.
POSSIBLE CAUSE	• PCM configuration has not been correctly performed • PCM connector or terminal malfunction • PCM malfunction
SYSTEM WIRING DIAGRAM	Not applicable

Diagnostic Procedure

Step

Inspection

Results

Action

1

RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION

Note

•  Recording can be facilitated using the screen capture function of the PC.

•  Record the freeze frame data/snap shot data.

—

Go to the next step.

2

PERFORM PCM CONFIGURATION (USING READ/WRITE FUNCTION)

•  Perform the PCM configuration (using read/write function).
(See PCM CONFIGURATION (USING READ/WRITE FUNCTION) [SKYACTIV-D 2.2])

•  Refer to the [MEMORY CLEARING PROCEDURE] and clear the DTC.
(See CLEARING DTC [PCM (SKYACTIV-D 2.2)])

•  Display the DTCs using the M-MDS.
(See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-D 2.2)])

•  Has DTC P0610:00 been recorded?

Yes

Go to the next step.

No

Go to Step 5.

3

INSPECT PCM CONNECTOR CONDITION

•  Switch the ignition OFF.

•  Disconnect the PCM connector.

•  Inspect the connector engagement and connection condition, and inspect the terminals for damage, deformation, corrosion, or disconnection.

•  Is the connector normal?

Yes

Perform the PCM configuration (using read/write function) again.

(See PCM CONFIGURATION (USING READ/WRITE FUNCTION) [SKYACTIV-D 2.2])

•  If the malfunction recurs, perform the PCM configuration (as-built data use).
(See PCM CONFIGURATION (USING AS-BUILT DATA) [SKYACTIV-D 2.2])

Go to the next step.

No

Repair or replace the connector, then go to the next step.

4

VERIFY THAT REPAIRS HAVE BEEN COMPLETED

•  Reconnect all the disconnected connectors.

•  Refer to the [MEMORY CLEARING PROCEDURE] and clear the DTC.
(See CLEARING DTC [PCM (SKYACTIV-D 2.2)])

•  Display the DTCs using the M-MDS.
(See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-D 2.2)])

•  Has DTC P0610:00 been recorded?

Yes

Replace the PCM, then go to the next step.

(See PCM REMOVAL/INSTALLATION [SKYACTIV-D 2.2])

No

Go to the next step.

5

VERIFY OTHER DTCs

•  Has any other DTC or pending code been stored?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

(See DTC TABLE [PCM (SKYACTIV-D 2.2)])

No

DTC troubleshooting completed.

Step	Inspection	Results	Action
1	RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION Note • Recording can be facilitated using the screen capture function of the PC. • Record the freeze frame data/snap shot data.	—	Go to the next step.
2	PERFORM PCM CONFIGURATION (USING READ/WRITE FUNCTION) • Perform the PCM configuration (using read/write function). (See PCM CONFIGURATION (USING READ/WRITE FUNCTION) [SKYACTIV-D 2.2]) • Refer to the [MEMORY CLEARING PROCEDURE] and clear the DTC. (See CLEARING DTC [PCM (SKYACTIV-D 2.2)]) • Display the DTCs using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-D 2.2)]) • Has DTC P0610:00 been recorded?	Yes	Go to the next step.
2		No	Go to Step 5.
3	INSPECT PCM CONNECTOR CONDITION • Switch the ignition OFF. • Disconnect the PCM connector. • Inspect the connector engagement and connection condition, and inspect the terminals for damage, deformation, corrosion, or disconnection. • Is the connector normal?	Yes	Perform the PCM configuration (using read/write function) again. (See PCM CONFIGURATION (USING READ/WRITE FUNCTION) [SKYACTIV-D 2.2]) • If the malfunction recurs, perform the PCM configuration (as-built data use). (See PCM CONFIGURATION (USING AS-BUILT DATA) [SKYACTIV-D 2.2]) Go to the next step.
3		No	Repair or replace the connector, then go to the next step.
4	VERIFY THAT REPAIRS HAVE BEEN COMPLETED • Reconnect all the disconnected connectors. • Refer to the [MEMORY CLEARING PROCEDURE] and clear the DTC. (See CLEARING DTC [PCM (SKYACTIV-D 2.2)]) • Display the DTCs using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-D 2.2)]) • Has DTC P0610:00 been recorded?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [SKYACTIV-D 2.2])
4		No	Go to the next step.
5	VERIFY OTHER DTCs • Has any other DTC or pending code been stored?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [PCM (SKYACTIV-D 2.2)])
5		No	DTC troubleshooting completed.