DTC C0049:85 [RADAR UNIT]

id1502a6017500

Description

Brake fluid level signal error

Detection condition

•  The front body control module (FBCM) continues the detected condition in which the brake fluid level is less than MIN for the specified period or more.

Fail-safe

•  Inhibits the Mazda radar cruise control (MRCC) system control

•  Inhibits the smart brake support (SBS) system control

•  Inhibits the distance recognition support system (DRSS) control

Possible cause

•  Insufficient brake fluid level

•  DTCs are stored in the front body control module (FBCM).

―  Signal error in circuit between front body control module (FBCM) and radar unit

―  Front body control module (FBCM) malfunction

•  Radar unit malfunction

System wiring diagram

Not applicable

Description	Brake fluid level signal error
Detection condition	• The front body control module (FBCM) continues the detected condition in which the brake fluid level is less than MIN for the specified period or more.
Fail-safe	• Inhibits the Mazda radar cruise control (MRCC) system control • Inhibits the smart brake support (SBS) system control • Inhibits the distance recognition support system (DRSS) control
Possible cause	• Insufficient brake fluid level • DTCs are stored in the front body control module (FBCM). ― Signal error in circuit between front body control module (FBCM) and radar unit ― Front body control module (FBCM) malfunction • Radar unit malfunction
System wiring diagram	Not applicable

Diagnostic Procedure

Step

Inspection

Action

1

INSPECT BRAKE FLUID LEVEL

•  Inspect the brake fluid level.
(See BRAKE FLUID LEVEL SENSOR INSPECTION.)

•  Is the brake fluid level normal?

Yes

Go to the next step.

No

Add genuine brake fluid, then go to Step 3.

2

PERFORM DTC INSPECTION FOR FRONT BODY CONTROL MODULE (FBCM)

•  Perform the front body control module (FBCM) DTC inspection using the M-MDS.
(See DTC INSPECTION [FRONT BODY CONTROL MODULE (FBCM)].)

•  Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [FRONT BODY CONTROL MODULE (FBCM)].)

Go to the next step.

No

Go to the next step.

3

VERIFY THAT REPAIRS HAVE BEEN COMPLETED

•  Clear radar unit DTCs using the M-MDS.
(See CLEARING DTC [RADAR UNIT].)

•  Switch the ignition ON (engine on).

•  Perform the radar unit DTC inspection using the M-MDS.
(See DTC INSPECTION [RADAR UNIT].)

•  Is the same Pending DTC present?

Yes

Repeat the inspection from Step 1.

•  If the malfunction does not recur, go to the next step.

•  If the malfunction recurs, replace the radar unit.
(See RADAR UNIT REMOVAL/INSTALLATION.)

Go to the next step.

No

Go to the next step.

4

VERIFY THAT NO OTHER DTCs ARE PRESENT

•  Verify other DTCs displayed.

•  Are any other DTCs output?

Yes

Perform the corresponding DTC inspection.

No

DTC troubleshooting completed.

Step	Inspection		Action
1	INSPECT BRAKE FLUID LEVEL • Inspect the brake fluid level. (See BRAKE FLUID LEVEL SENSOR INSPECTION.) • Is the brake fluid level normal?	Yes	Go to the next step.
1		No	Add genuine brake fluid, then go to Step 3.
2	PERFORM DTC INSPECTION FOR FRONT BODY CONTROL MODULE (FBCM) • Perform the front body control module (FBCM) DTC inspection using the M-MDS. (See DTC INSPECTION [FRONT BODY CONTROL MODULE (FBCM)].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [FRONT BODY CONTROL MODULE (FBCM)].) Go to the next step.
2		No	Go to the next step.
3	VERIFY THAT REPAIRS HAVE BEEN COMPLETED • Clear radar unit DTCs using the M-MDS. (See CLEARING DTC [RADAR UNIT].) • Switch the ignition ON (engine on). • Perform the radar unit DTC inspection using the M-MDS. (See DTC INSPECTION [RADAR UNIT].) • Is the same Pending DTC present?	Yes	Repeat the inspection from Step 1. • If the malfunction does not recur, go to the next step. • If the malfunction recurs, replace the radar unit. (See RADAR UNIT REMOVAL/INSTALLATION.) Go to the next step.
3		No	Go to the next step.
4	VERIFY THAT NO OTHER DTCs ARE PRESENT • Verify other DTCs displayed. • Are any other DTCs output?	Yes	Perform the corresponding DTC inspection.
4		No	DTC troubleshooting completed.