MAINTENANCE MONITOR OPERATION PROCEDURE

id092200036700

European Specs.

Note

•  When any of the display conditions is met from the preset maintenance period, the maintenance monitor displays a message.

Display condition

―  Day-setting: Remaining days are 15 days or less

―  Distance setting: Remaining distance is 500 km/250 mile

―  Request signal is received from PCM (engine oil only)

•  The instrument cluster displays a message for which the display conditions are met 0.8 after the ignition is switched ON (engine off or on).

•  If several display conditions are met, the instrument cluster displays a message at approx. 5 s intervals according to the following order of precedence.

1.  Scheduled Maintenance

2.  Tire Rotation

3.  Tire Pressure

4.  Engine Oil ( Only maintenance interval of engine oil is one year or 20,000 km)

•  If the engine oil is replaced on vehicles in which the engine oil maintenance monitor setting is on, perform engine oil data reset to clear the total traveled distance and elapsed time recorded by the PCM. (See ENGINE OIL DATA RESET [SKYACTIV-D 2.2].) (See ENGINE OIL DATA RESET [SKYACTIV-G 2.0, SKYACTIV-G 2.5].)

•  The instrument cluster stores the maintenance monitor setting content, and the elapsed time and traveled distance from when the setting was made. The stored setting information is not cleared even if the battery is removed.

•  Because the maintenance monitor setting information stored in the instrument cluster cannot be written to a new instrument cluster, if the instrument cluster is replaced, the maintenance monitor is the initial set value. Before replacing the instrument cluster, explain to the customer that the maintenance monitor is reset to the initial setting.

Scheduled maintenance setting procedure

1.  Switch the ignition ON (engine off or on).

2.  Select "Setting" by operating the up/down switch and INFO button for the steering switch.

3.  Select "Maintenance" by operating the up/down switch and INFO button for the steering switch.

4.  Select "Scheduled" by operating the up/down switch and INFO button for the steering switch.

5.  Select the following items and change the setting.

LCD	Function	Initial setting	Setting contents	Control unit
Set Time	Set days until scheduled maintenance is displayed.	12 months	1-36 month	Instrument cluster
Set Distance	Set distance until scheduled maintenance is displayed.	20,000 km/12,500 miles	0-99500 km(0-99750miles)	Instrument cluster
OFF	Turn off scheduled maintenance display.	—	—	Instrument cluster

Tire rotation setting procedure

1.  Switch the ignition ON (engine off or on).

2.  Select "Setting" by operating the up/down switch and INFO button for the steering switch.

3.  Select "Maintenance" by operating the up/down switch and INFO button for the steering switch.

4.  Select "Tire Rotation" by operating the up/down switch and INFO button for the steering switch.

5.  Select the following items and change the setting.

LCD	Function	Initial setting	Setting contents	Control unit
Set Distance	Set distance until tire rotation is displayed.	10,000 km/6,250 miles	0-99500 km(0-99750miles)	Instrument cluster
OFF	Turn off tire rotation display.	—	—	Instrument cluster

Tire pressure setting procedure

1.  Switch the ignition ON (engine off or on).

2.  Select "Setting" by operating the up/down switch and INFO button for the steering switch.

3.  Select "Maintenance" by operating the up/down switch and INFO button for the steering switch.

4.  Select "Tire Pressure" by operating the up/down switch and INFO button for the steering switch.

5.  Select the following items and change the setting.

LCD	Function	Initial setting	Setting contents	Control unit
Set Time	Set day until tire pressure is displayed.	12 months	1-36 month	Instrument cluster
OFF	Turn off tire pressure display.	—	—	Instrument cluster

Engine oil maintenance monitor Setting Procedure

1.  Verify that a vehicle which has an engine oil and maintenance monitor setting is a vehicle with an engine oil replacement interval of one year or 20,000 km.

Maintenance interval of engine oil is one year or 20,000 km

•  Albania, Austria, Belgium, Bosnia-herzegovina, Bulgaria, Croatia, Czech, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Macedonia, Moldova, Montenegro, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, The Netherlands, U.k., Ukraine

Caution

•  Do not turn on the engine oil maintenance monitor for the following driving conditions even if the engine oil interval is one year or 20,000 km.

―  The vehicle is used as a police car, taxi, or for driving instruction.

―  Driving under dusty conditions.

―  Extended periods of idling or low speed operation.

―  Driving for long periods in cold temperatures or driving regularly for short distances only.

―  Driving under extremely hot conditions.

―  Driving continually in mountainous regions.

2.  Connect the M-MDS to the DLC-2.

3.  After vehicle identification, the following can be selected from the M-MDS initialization screen.

(1)  "Powertrain"

(2)  "Engine Oil Maintenance Monitor"

4.  Select "ON" or "OFF" from the M-MDS screen.

Engine oil maintenance monitor reset procedure

1.  For the engine oil maintenance monitor reset procedures, refer to the ENGINE OIL DATA RESET. (See ENGINE OIL DATA RESET [SKYACTIV-D 2.2].) (See ENGINE OIL DATA RESET [SKYACTIV-G 2.0, SKYACTIV-G 2.5].)

Maintenance monitor reset procedure

Note

•  This procedure is for returning all of the set content in the maintenance monitor, back to the initial settings.

1.  Switch the ignition ON (engine off or on).

2.  Select "Setting" by operating the up/down switch and INFO button for the steering switch.

3.  Select the following items and change the setting.

LCD	Function	Initial setting	Setting contents	Control unit
Restore Defaults	Return the maintenance monitor setting content to the initial value.	No	No/Yes	Instrument cluster

Maintenance monitor display/non-display setting procedure

Note

•  This procedure is for setting all maintenance monitors, to display/non-display. If display/non-display is set for each item, select "OFF" using the setting procedure for each item.

1.  Switch the ignition ON (engine off or on).

2.  Select "Setting" by operating the up/down switch and INFO button for the steering switch.

3.  Select "Maintenance" by operating the up/down switch and INFO button for the steering switch.

4.  Select the following items and change the setting.

LCD	Function	Initial setting	Setting contents	Control unit
Messages	Set maintenance monitor display (ON)/non-display (OFF). Note •  If the monitor is set to "OFF", the maintenance content is not displayed, however, the set value is counted.	ON	ON/OFF	Instrument cluster

Except European Specs.

Note

•  When any of the display conditions is met from the preset maintenance period, the maintenance monitor displays a message.

Display condition

―  Day-setting: Remaining days are 15 days or less

―  Distance setting: Remaining distance is 500 km/250 mile

•  The instrument cluster displays a message for which the display conditions are met 0.8 after the ignition is switched ON (engine off or on).

•  If several display conditions are met, the instrument cluster displays a message at approx. 5 s intervals according to the following order of precedence.

1.  Scheduled Maintenance

2.  Tire Rotation

3.  Tire Pressure

4.  Engine Oil

•  The instrument cluster stores the maintenance monitor setting content, and the elapsed time and traveled distance from when the setting was made. The stored setting information is not cleared even if the battery is removed.

•  Because the maintenance monitor setting information stored in the instrument cluster cannot be written to a new instrument cluster, if the instrument cluster is replaced, the maintenance monitor is the initial set value. Before replacing the instrument cluster, explain to the customer that the maintenance monitor is reset to the initial setting.

Scheduled maintenance setting procedure

1.  Switch the ignition ON (engine off or on).

2.  Select "Setting" by operating the up/down switch and INFO button for the steering switch.

3.  Select "Maintenance" by operating the up/down switch and INFO button for the steering switch.

4.  Select "Scheduled" by operating the up/down switch and INFO button for the steering switch.

5.  Select the following items and change the setting.

LCD	Function	Initial setting	Setting contents	Control unit
Set Time	Set days until scheduled maintenance is displayed.	6 months	1-36 month	Instrument cluster
Set Distance	Set distance until scheduled maintenance is displayed.	10,000 km/6,250 miles	0-99500 km(0-99750miles)	Instrument cluster
OFF	Turn off scheduled maintenance display.	—	—	Instrument cluster

Tire rotation setting procedure

1.  Switch the ignition ON (engine off or on).

2.  Select "Setting" by operating the up/down switch and INFO button for the steering switch.

3.  Select "Maintenance" by operating the up/down switch and INFO button for the steering switch.

4.  Select "Tire Rotation" by operating the up/down switch and INFO button for the steering switch.

5.  Select the following items and change the setting.

LCD	Function	Initial setting	Setting contents	Control unit
Set Distance	Set distance until tire rotation is displayed.	10,000 km/6,250 miles	0-99500 km(0-99750miles)	Instrument cluster
OFF	Turn off tire rotation display.	—	—	Instrument cluster

Tire pressure setting procedure

1.  Switch the ignition ON (engine off or on).

2.  Select "Setting" by operating the up/down switch and INFO button for the steering switch.

3.  Select "Maintenance" by operating the up/down switch and INFO button for the steering switch.

4.  Select "Tire Pressure" by operating the up/down switch and INFO button for the steering switch.

5.  Select the following items and change the setting.

LCD	Function	Initial setting	Setting contents	Control unit
Set Time	Set day until tire pressure is displayed.	6 months	1-36 month	Instrument cluster
OFF	Turn off tire pressure display.	—	—	Instrument cluster

Engine oil maintenance monitor setting procedure

1.  Switch the ignition ON (engine off or on).

2.  Select "Setting" by operating the up/down switch and INFO button for the steering switch.

3.  Select "Maintenance" by operating the up/down switch and INFO button for the steering switch.

4.  Select "Oil Change" by operating the up/down switch and INFO button for the steering switch.

5.  Select the following items and change the setting.

LCD	Function	Initial setting	Setting contents	Control unit
Set Distance	Set distance until engine oil maintenance monitor is displayed.	10,000 km/6,250 miles	0-99500 km(0-99750miles)	Instrument cluster
OFF	Turn off engine oil maintenance monitor display.	—	—	Instrument cluster

Maintenance monitor reset procedure

Note

•  This procedure is for returning all of the set content in the maintenance monitor, engine oil maintenance monitor, back to the initial settings.

1.  Switch the ignition ON (engine off or on).

2.  Select "Setting" by operating the up/down switch and INFO button for the steering switch.

3.  Select the following items and change the setting.

LCD	Function	Initial setting	Setting contents	Control unit
Restore Defaults	Return the maintenance monitor setting content to the initial value.	No	No/Yes	Instrument cluster

Maintenance monitor display/non-display setting procedure

Note

•  This procedure is for setting all maintenance monitors, engine oil maintenance monitor, to display/non-display. If display/non-display is set for each item, select "OFF" using the setting procedure for each item.

1.  Switch the ignition ON (engine off or on).

2.  Select "Setting" by operating the up/down switch and INFO button for the steering switch.

3.  Select "Maintenance" by operating the up/down switch and INFO button for the steering switch.

4.  Select the following items and change the setting.

LCD	Function	Initial setting	Setting contents	Control unit
Messages	Set maintenance monitor display (ON)/non-display (OFF). Note •  If the monitor is set to "OFF", the maintenance content is not displayed, however, the set value is counted.	ON	ON/OFF	Instrument cluster