DIAGNOSTIC ASSIST FUNCTION [AUDIO]


id0902f6361100


Switch Inspection

1.  Switch the ignition to ACC or ON.

2.  Turn the audio unit power to on.

3.  While pressing the POWER/VOLUME switch, simultaneously press the Preset switch “3” for approx. 0.2 s.

With RDS (radio data system)

am6zzw00002516

Without RDS (radio data system)

am6zzw00003334

4.  Inspect according to the following table:

Inspection

Display

Action

•  Launch the switch inspection mode.
•  Operate all of the switches (press).
•  Does the buzzer sound?
Yes
The switch is normal.
No
Verify the switch.

5.  Cancel the diagnostic assist function by either turning off the audio unit power or by switch the ignition to off.


Speaker Inspection

1.  Switch the ignition to ACC or ON.

2.  Turn the audio unit power to on.

3.  While pressing the POWER/VOLUME switch, simultaneously press the AUTO MEMORY switch for approx. 0.2 s.

With RDS (radio data system)

am6zzw00002517

Without RDS (radio data system)

am6zzw00003335

4.  Inspect according to the following table:

Inspection

Display

Action

•  Launch the speaker inspection mode.
•  Does each speaker output sound in the following order?:
Without Bose®
1.  Front door speaker (LH) and tweeter (LH) (with 6 speaker type)
2.  Front door speaker (RH) and tweeter (RH) (with 6 speaker type)
3.  Rear door speaker (RH)
4.  Rear door speaker (LH)
With Bose®
1.  Front door speaker (LH) and tweeter (LH) and center speaker
2.  Front door speaker (RH) and tweeter (RH) and center speaker
3.  Rear door speaker (RH) and rear speaker (4SD) /bass-box (5HB/WGN)
4.  Rear door speaker (LH) and rear speaker (4SD) /bass-box (5HB/WGN)
Yes
The speakers and the wiring harness between the audio unit and speakers are normal.
No
•  If no sound is produced from all of the speakers.
•  If no sound is produced from some of the speakers.

5.  Cancel the diagnostic assist function by either turning off the audio unit power or by switch the ignition to off.


Radio Reception Condition Inspection

1.  Switch the ignition to ACC or ON.

2.  Turn the audio unit power to on.

3.  Tune in the radio.

4.  While pressing the POWER/VOLUME switch, simultaneously press the Preset switch “2” for approx. 0.2 s.

With RDS (radio data system)

am6zzw00002518

Without RDS (radio data system)

am6zzw00003336

5.  Inspect according to the following table:

Caution
•  Even if the system is normal, radio reception may be difficult depending on where the system is inspected (indoors/outdoors, or conditions at the location). Before inspecting the system, verify that radio reception is adequate.
•  When performing the inspection, select the best area for receiving radio frequencies.

Inspection

Display (AM 522 kHz reception)

Action

Start the radio reception condition inspection mode.
Glass antenna, antenna feeder and audio unit are normal.
Change frequencies and re-perform the inspection.
Inspect the glass antenna and antenna feeder and antenna amplifier.
•  If either the glass antenna or the antenna feeder is not normal, replace the malfunctioning part.
•  If the glass antenna and antenna feeder are normal, replace the audio unit.

6.  Cancel the diagnostic assist function by either turning off the audio unit power or by switch the ignition to off.


Antenna Control Condition Inspection

1.  Switch the ignition to ACC or ON.

2.  Turn the audio unit power to on.

3.  Tune in the radio.

4.  While pressing the POWER/VOLUME switch, simultaneously press the AM switch for approx. 0.2 s or more.

With RDS (radio data system)

am6zzw00002519

Without RDS (radio data system)

am6zzw00003337

5.  Inspect according to the following table:

Inspection

Display

Action

Start antenna control condition inspection mode.
Sound quality good.
System is okay.
Sound quality poor.
Inspect the glass antenna and antenna feeder and antenna amplifier.
Replace the audio unit.

6.  Cancel the diagnostic assist function by either turning off the audio unit power or by switch the ignition to off.


Audio Amplifier Control Condition Inspection

1.  Switch the ignition to ACC or ON.

2.  Turn the audio unit power to on.

3.  Tune in the radio.

4.  While pressing the AUTO MEMORY switch, simultaneously press the CD switch for approx. 0.2 s or more.

With RDS (radio data system)

am6zzw00002694

Without RDS (radio data system)

am6zzw00003338

5.  Inspect according to the following table:

Inspection

Display

Action

Start audio amplifier control condition inspection mode.
System is okay.
Replace the audio unit.

6.  Cancel the diagnostic assist function by either turning off the audio unit power or by switch the ignition to off.


Dial Inspection

1.  Switch the ignition to ACC or ON.

2.  Turn the audio unit power to on.

3.  While pressing the AUTO MEMORY switch, simultaneously press the preset switch “1” for approx. 2 s or more.

With RDS (radio data system)

am6zzw00002524

Without RDS (radio data system)

am6zzw00003339

4.  Inspect according to the following table:

Inspection

Display

Action

•  Launch the dial inspection mode.
•  Operate all of the dial.
•  Does the dial rotation direction correspond with the direction displayed in information display?
Yes
Dial is okay.
No
Verify the switch.

5.  Cancel the diagnostic assist function by either turning off the audio unit power or by switch the ignition to off.


Audio Amplifier Specification Inspection

1.  Switch the ignition to ACC or ON.

2.  Turn the audio unit power to on.

3.  While pressing the POWER/VOLUME switch, simultaneously press the SEEK switch (down) for approx. 2 s or more.

With RDS (radio data system)

am6zzw00002531

Without RDS (radio data system)

am6zzw00003340

4.  Inspect according to the following table:

Inspection

Display

Action

•  Launch audio amplifier specification inspection mode.
•  Verify the audio amplifier specification.
•  Dose the audio amplifier specification correspond.
Yes
System is okay.
No
Replace the audio unit.

5.  Cancel the diagnostic assist function by either turning off the audio unit power or by switch the ignition to off.