DTC P0030 [13B-MSP]
id0102g1801900
DTC P0030 |
A/F sensor heater control circuit problem |
---|---|
DETECTION CONDITION
|
• The PCM monitors the A/F sensor impedance when under the A/F sensor heater control for 190 s. If the impedance is more than 44 ohms while PCM turns A/F sensor heater on, the PCM determines that there is a A/F sensor heater control circuit problem.
Diagnostic support note
• This is a continuous monitor (A/F sensor heater, HO2S heater).
• The MIL illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM.
• PENDING CODE is available if the PCM detects the above malfunction condition during the first drive cycle.
• FREEZE FRAME DATA is available.
• The DTC is stored in the PCM memory.
|
POSSIBLE CAUSE
|
• Connector or terminal malfunction
• A/F sensor heater malfunction
• PCM malfunction
|
Diagnostic procedure
STEP |
INSPECTION |
ACTION |
|
---|---|---|---|
1
|
VERIFY FREEZE FRAME DATA AND DIAGNOSTIC MONITORING TEST RESULTS HAVE BEEN RECORDED
• Have FREEZE FRAME DATA and DIAGNOSTIC MONITORING TEST RESULTS (A/F sensor heater, HO2S heater related) been recorded?
|
Yes
|
Go to the next step.
|
No
|
Record the FREEZE FRAME DATA and DIAGNOSTIC MONITORING TEST RESULTS on the repair order, then go to the next step.
|
||
2
|
VERIFY RELATED SERVICE INFORMATION AVAILBAILITY
• Verify related Service information availability.
• Is any related Service information available?
|
Yes
|
Perform repair or diagnosis according to the available Service information.
• If the vehicle is not repaired, go to the next step.
|
No
|
Go to the next step.
|
||
3
|
VERIFY RELATED PENDING CODE OR STORED DTC
• Turn the ignition switch off, then to the ON position (engine off).
• Verify the related PENDING CODE or stored DTCs.
• Are other DTCs present?
|
Yes
|
Go to the appropriate DTC inspection.
(See DTC TABLE [13B-MSP].)
|
No
|
Go to the next step.
|
||
4
|
INSPECT A/F SENSOR CONNECTOR FOR POOR CONNECTION
• Turn the ignition switch off.
• Disconnect the A/F sensor connector.
• Inspect for poor connection (such as damaged/pulled-out pins, and corrosion).
• Is there any malfunction?
|
Yes
|
Repair or replace the terminal, then go to Step 7.
|
No
|
Go to the next step.
|
||
5
|
INSPECT A/F SENSOR HEATER
• Inspect the A/F sensor heater.
• Is there any malfunction?
|
Yes
|
Replace the A/F sensor, then go to Step 7.
|
No
|
Go to the next step.
|
||
6
|
INSPECT PCM CONNECTOR FOR POOR CONNECTION
• Turn the ignition switch off.
• Disconnect the PCM connector.
• Inspect for poor connection (such as damaged/pulled-out pins, and corrosion).
• Is there any malfunction?
|
Yes
|
Repair or replace the terminal, then go to the next step.
|
No
|
Go to the next step.
|
||
7
|
VERIFY TROUBLESHOOTING OF DTC P0030 COMPLETED
• Make sure to reconnect all disconnected connectors.
• Clear the DTC from the PCM memory using the M-MDS.
• Perform the DRIVE MODE 03.
(See OBD DRIVE MODE [13B-MSP].)
• Is the PENDING CODE same as the DTC present?
|
Yes
|
Replace the PCM, then go to the next step.
|
No
|
Go to the next step.
|
||
8
|
VERIFY AFTER REPAIR PROCEDURE
• Perform the “AFTER REPAIR PROCEDURE”.
• Are any DTCs present?
|
Yes
|
Go to the applicable DTC inspection.
(See DTC TABLE [13B-MSP].)
|
No
|
DTC troubleshooting completed.
|