Transmission Control Module Codes

ETC (722.6) [5-Gear] as of 2006

DTC TEST SCOPE

0601 Component N15/3 (ETC [EGS] control unit) is faulty.�

0604 Component N15/3 (ETC [EGS] control unit) is faulty.�

0605 Component N15/3 (ETC [EGS] control unit) is faulty.�

0613 Component N15/3 (ETC [EGS] control unit) is faulty.�

0642 The voltage supply of the speed sensors is faulty.�

0643 The supply voltage of the sensors is too high (overvoltage).�

0657 The voltage supply of the valves is faulty.�

0702 Component N15/3 (ETC [EGS] control unit) is faulty.�

0710 The signal of component Y3/6b1 (Transmission oil temperature sensor) and (or) Y3/6s1 (Starter lockout contact) is implausible.�

0712 Component Y3/6s1 (Starter lockout contact) or component Y3/6b1 (Transmission oil temperature sensor) is faulty or both.�

0714 The signal of component Y3/6b1 (Transmission oil temperature sensor) and (or) Y3/6s1 (Starter lockout contact) is implausible.�

0717 Component Y3/6n2 (speed sensor 2) is faulty or the sensor supply has Open circuit.�

0730 The transmission has an impermissible transmission ratio.�

0731 The gear is implausible or the transmission is slipping. ( 1. gear )�

0732 The gear is implausible or the transmission is slipping. ( 2. gear )�

0733 The gear is implausible or the transmission is slipping. ( 3. gear )�

0734 The gear is implausible or the transmission is slipping. ( 4. gear )�

0735 The gear is implausible or the transmission is slipping. ( 5. gear )�

0741 Actuation of torque converter lockup clutch is not possible.�

0742 The torque converter lock-up clutch causes impermissible closing.�

0743 The internal electrical check of component Y3/6y6 (Torque converter lockup PWM solenoid valve) has failed.�

0748 The internal electrical check of component Y3/6y1 (Modulating pressure control solenoid valve) has failed.�

0752 Component Y3/6y3 (1-2 and 4-5 shift solenoid valve) has Short circuit to ground.�

0753 The internal electrical check of component Y3/6y3 (1-2 and 4-5 shift solenoid valve) has failed.�

0757 Component Y3/6y5 (2-3 shift solenoid valve) has Short circuit to ground.�

0758 The internal electrical check of component Y3/6y5 (2-3 shift solenoid valve) has failed.�

0762 Component Y3/6y4 (3-4 shift solenoid valve) has Short circuit to ground.�

0763 The internal electrical check of component Y3/6y4 (3-4 shift solenoid valve) has failed.�

0778 The internal electrical check of component Y3/6y2 (Shift pressure control solenoid valve) has failed.�

1629 Component N15/3 (ETC [EGS] control unit) is faulty.�

1631 Component N15/3 (ETC [EGS] control unit) is faulty.�

1632 Component N15/3 (ETC [EGS] control unit) is faulty.�

1633 Component N15/3 (ETC [EGS] control unit) is faulty.�

1634 Component N15/3 (ETC [EGS] control unit) is faulty.�

1636 Component N15/3 (ETC [EGS] control unit) is faulty.�

1637 Component N15/3 (ETC [EGS] control unit) is faulty.�

1638 Component N15/3 (ETC [EGS] control unit) is faulty.�

1639 Component N15/3 (ETC [EGS] control unit) is faulty.�

1704 Excessive rpms have occurred at component Y3/6n2 (speed sensor 2).�

1705 Excessive rpms have occurred at component Y3/6n3 (speed sensor 3).�

1731 The gear comparison is negative or the target gear is not reached.�

220B The speed of Y3/6n2 or Y3/6n3 is too high.�

2502 The gear is implausible or the transmission is slipping.�

2603 The voltage supply of the speed sensors is faulty.�

2746 Excessive rpms have occurred at component Y3/6n2 (speed sensor 2).�

2750 Excessive rpms have occurred at component Y3/6n3 (speed sensor 3).�

2767 Component Y3/6n3 (speed sensor 3) is faulty.�

2783 The torque converter lock-up clutch has excessive power consumption.�

2784 The comparison of the rpms between component Y3/6n2 (speed sensor 2) and Y3/6n3 (speed sensor 3) is implausible.�

C002 CAN communication with other control units installed in this vehicle is not possible. ( Bus OFF fault )�

D601 Error during programming�

D60E Boot software Fault�

E0501 The wheel rpms from the traction system are not available on the CAN bus. ( CAN timeout fault )�

E0562 The voltage supply of circuit 87 has undervoltage.�

E0563 The voltage supply of circuit 87 has overvoltage.�

E0602 Control module N15/3 (ETC [EGS] control unit) is not coded.�

E0822 Selector lever coding is invalid.�

E0824 The selector lever is in an intermediate position.�

E0914 Selector lever coding is invalid.�

E0928 The cable to component Y66/1 (Reversing and parking lock solenoid) has short circuit or no connection.�

E1644 The coding of the control unit N15/3 (ETC [EGS] control unit) is impermissible.�

E2638 The feedback through the transmission protection is not maintained.�

E301 CAN communication with other control units installed in this vehicle is not possible. ( Bus OFF fault )�

EC100 CAN communication with the engine system is faulty. ( CAN timeout fault )�

EC103 Fault in CAN communication with component N15/5 (Electronic selector lever module control unit). ( CAN timeout fault )�

EC121 CAN communication with the traction system is faulty. ( CAN timeout fault )�

EC141 Communication disturbance with control module N73 (EIS [EZS] control unit). ( CAN timeout fault )�

EC155 Communication disturbance with control module A1 (Instrument cluster). ( CAN timeout fault )�

EC164 Communication disturbance with control module N22/7 (Automatic air conditioning control and operating unit). ( CAN timeout fault )�

EC401 The CAN signals sent from control unit Engine management are incomplete.�

EC404 The selector lever position sent from control unit N15/5 (Electronic selector lever module control unit) via the CAN bus is implausible.�

EC415 The CAN signals sent from control unit N47-5 (ESP control unit) are incomplete.�

EC423 The CAN signals sent from control unit A1 (Instrument cluster) are incomplete.�

EC424 The CAN signals sent from control unit N22/7 (Automatic air conditioning control and operating unit) are incomplete.�

EC428 The CAN signals from the steering angle sensor that were sent via control unit N80 (Steering column module) were not received.�

EC429 The CAN signals from the steering wheel shift buttons that were sent via control unit N80 (Steering column module) were not received.�

EC431 The CAN signals sent from control unit N73 (EIS [EZS] control unit) are incomplete.�

ED10B CAN communication with the engine system is faulty. ( CAN timeout fault )�

ED118 Message 'Variant coding' from control unit Engine management is not available on the CAN bus. ( CAN timeout fault )�

ED139 Fault in CAN communication with control unit N80 (Steering column module). ( CAN timeout fault )�

ED13A Fault in CAN communication with control unit N80 (Steering column module). ( CAN timeout fault )�

ED400 The accelerator pedal value from the engine control is not available on the CAN bus. ( CAN timeout fault )�

ED401 The engine speed from the engine control is not available on the CAN bus. ( CAN timeout fault )�

ED402 The engine temperature from the engine control is not available on the CAN bus. ( CAN timeout fault )�

ED404 The static torque requirement from the engine control is not available on the CAN bus. ( CAN timeout fault )�

ED405 The minimum torque requirement from the engine control is not available on the CAN bus. ( CAN timeout fault )�

ED406 The maximum torque requirement from the engine control is not available on the CAN bus. ( CAN timeout fault )�

ED407 The torque requirement for the traction system from the engine control is not available on the CAN bus. ( CAN timeout fault )�

ED408 The stop lamp switch signal from the traction system is not available on the CAN bus. ( CAN timeout fault )�

ED409 The left front wheel rpm signal from the traction system is not available on the CAN bus. ( CAN timeout fault )�

ED40A The right front wheel rpm signal from the traction system is not available on the CAN bus. ( CAN timeout fault )�

ED40B The left rear wheel rpm signal from the traction system is not available on the CAN bus. ( CAN timeout fault )�

ED40C The right rear wheel rpm signal from the traction system is not available on the CAN bus. ( CAN timeout fault )�

ED40F The signal for the variant of the engine control is invalid.�

ED420 The signals sent by the control through component N80 (Steering column module) are not available from the CAN bus. ( CAN timeout fault )�

ED505 The CAN signals sent from control unit N78 (Transfer case control module) are incomplete.�

ED507 The CAN signals sent from control unit Engine management are incomplete.�

ED508 The signals sent from control unit N15/5 (Electronic selector lever module control unit) or A80 (Intelligent servo module for DIRECT SELECT) through the CAN bus are incomplete.�

ED509 The CAN signals sent from control unit Engine management are incomplete.�

EE318 Fault in CAN communication with component N15/5 (Electronic selector lever module control unit). ( CAN timeout fault )�

EE338 The CAN signals sent from control unit N80 (Steering column module) are incomplete.