Operation CHARM: Car repair manuals for everyone.

Computers/Control - DAS/XD Add-On 2009-09-28-1266

DAS/XD ADD-ON 2009-09-28-1266 FOR PASSENGER CARS

Topic number LI58.40-P-048526

Version 1

Design group 58.40 Workshop equipment/MB testers

Date 11-25-2009

Validity DVD version 09/2009

Reason for change

Reason for block

Complaint:

CDID2

Model series: 204, 212

DAS personalizing cannot be performed

MCMSFL221 / MCMSFR221

Model series: 221 model ref. pkge.

Multicontour seat fails during air release procedure. The system becomes operational again after an ignition change.

Fault code 9E8900 is stored.

TV tuner

Model series: 221, 216

Notes adjusted with respect to. coding/extended options. Required in case of replacement of TV-05 (221) with TV-09 (221 model refinement package).

SRS/airbag

Model series: X204

FC A208 cannot be erased even when stored.

ME

Model series: 204, 207, 212

Control unit programming for software 0094487540 reports: "The following control unit software versions are available for control unit programming: 0094487540" After control unit programming, the control unit cannot be started up.

DTR

Model series: 221, 216

Control unit programming for hardware object number 2125450416 reports:

"The following control unit software versions are available for control unit programming: 2214420956" The control unit cannot be programmed."

CDI 5

Model series: 211

Control unit programming for software object number 010 448 51 40 reports: "No newer control unit software found".

ME

Model series: 451

Control unit programming for software object numbers 033 447 24 02 and 017 448 27 02 reports: "No newer control unit software found".

ME 9.7

Model series: 221

Control unit programming for several software object numbers reports: "No newer control unit software found".

ESP

Model series: 230

Control unit programming for software object numbers 230 448 02 02 and 211 448 08 02 reports: "No newer control unit software found".

ME 9.7

Model series: 219, 171

Control unit programming for hardware object number 0034467640 reports: "Control unit software versions are available for control unit programming". After control unit programming, the control unit cannot be started up.

ETC

Model series: 204

Control unit programming for software object number 002 448 48 10 reports: "No newer control unit software found".

DCU-RF

Model series: 221

Control unit programming for hardware object number 221 870 96 91 reports: "Control unit software versions are available for control unit programming". After control unit programming, the control unit cannot be started up.

ETC

Model series: 207

Control unit programming for software object number 002 448 54 10 reports: "No newer control unit software found".

ME9.7 (AMG)

Model series: 216, 221, 230

Control unit programming for several software object numbers reports: "No newer control unit software found".

ETC

Model series: 164, 251

The new transmission control unit VGS3NAG2 could not previously be programmed.

All flashable CUs

Model series: 204, 207, 212

FDOK redocumentation of CVN is not performed during SCN coding - SCN coding on vehicles with China variant of COMAND not possible. - Enabling offline control unit programming not possible.

SIM271DE20

Model series: 204, 207, 212

SCN is not written during SCN coding

Cause:

For all complaints: XD and DAS diagnostic data.

Remedy:

DAS/XD add-on 2009-09-28-1266 for passenger cars:

This add-on can be installed over DAS/XD version 09/2009.

This add-on does not supersede any other add-ons and must be additionally installed.





Symptoms
















































































Control unit/fault code