DTC 11
DTC 11: Wheel Speed Sensor (Open circuit or short circuit)
Part 1 of 2
Part 2 of 2
CIRCUIT OPERATION
^ A toothed ABS rotor generates a voltage pulse as it moves across the pickup field of each wheel speed sensor.
^ The amount of voltage generated at each wheel is determined by the clearance between the ABS rotor teeth and the wheel speed sensor, and by the speed of rotation.
^ The wheel speed sensors transmit the frequency of the voltage pulses and the amount of voltage generated by each pulse to the ABS electronic control unit (ABS-ECU).
^ The ABS hydraulic unit modulates the amount of braking force individually applied to each wheel cylinder.
ABS DTC SET CONDITIONS
^ DTCs 11, 12, 13, 14 are output when signal is not input due to breakage of the (+) or (-) wire of one or more of the four wheel-speed sensors. DTCs 21, 22, 23 24 are output in the following cases:
^ Open circuit is not found but no input is received by one or more of the four wheel-speed sensors at 10 km/h (6 mph) or more.
^ Sensor output drops due to a malfunctioning sensor or warped ABS rotor.
TROUBLESHOOTING HINTS (The most likely causes for these DTCs to set are:)
DTC 11, 12, 13, 14
^ Malfunction of the wheel speed sensor
^ Damaged wiring harness or connector
^ Malfunction of the hydraulic unit (Integrated with ABS-ECU)
DTC 21, 22, 23, 24
^ Malfunction of the wheel speed sensor
^ Damaged wiring harness and connector
^ Malfunction of the hydraulic unit (Integrated with ABS-ECU)
^ Malfunction of the ABS rotor
^ Malfunction of the wheel bearing
^ Excessive clearance between the sensor and ABS rotor
DIAGNOSIS
Required Special Tool:
^ MB991223: Harness Set
STEP 1. Check the wheel speed sensor installation.
Q: Is the wheel speed sensor bolted securely in place at the front knuckle or the rear knuckle?
YES: Go to Step 2.
NO: Install it properly. Then go to Step 9.
STEP 2. Check wheel speed sensor circuit at the ABS-ECU connector A-03.
1. Disconnect connector A-03 and measure at the harness side.
2. Measure the resistance between the ABS-ECU connector terminals 1 and 2, 5 and 6, 19 and 20, 22 and 23.
Standard Value: 1.28 - 1.92 k ohms
Q: Is the resistance between terminals 1 and 2, 5 and 6, 19 and 20, 22 and 23 within the standard value?
YES: Go to Step 6.
NO: Go to Step 3, 4 or 5.
STEP 3. Check the harness wires between ABS-ECU connector A-03 and wheel speed sensor
NOTE: After inspecting intermediate connector C-05, inspect the wires. If intermediate connector C-05 is damaged, repair or replace it. If the connector has been repaired or replaced, go to Step 9.
Q: Are any harness wires between ABS-ECU connector A-03 and wheel speed sensor
YES: Repair them and go to Step 9.
NO: Go to Step 7.
STEP 4. Check the harness wires between ABS-ECU connector A-03 and wheel speed sensor
Q: Are any harness wires between ABS-ECU connector A-03 and wheel speed sensor
YES: Repair them and then go to Step 9.
NO: Go to Step 7.
STEP 5. Check the harness wires between ABS-ECU connector A-03 and wheel speed sensor connector D-12
NOTE:
Q: Are any harness wires between ABS-ECU connector A-03 and wheel speed sensor connector D-12
YES: Repair them and then go to Step 9.
NO: Go to Step 7.
STEP 6. Check the wheel speed sensor output voltage.
Output Voltage:
^ When measured with a voltmeter: 42 mV or more
^ When measured with oscilloscope (maximum voltage): 200 mV or more
Q: Does the voltage meet the specification?
YES: Replace the hydraulic unit (integrated with ABS-ECU) and then go to Step 9.
NO: Go to Step 7.
STEP 7. Check the wheel speed sensor and ABS rotor.
If there is damaged in any of the check items, replace the wheel speed sensor.
Check items:
^ Wheel speed sensor internal resistance
Standard value: 1.28 - 1.92 k ohms
^ Wheel speed sensor insulation resistance
Standard value: 100 k ohms
^ Toothed ABS rotor check
Q: Is the wheel speed sensor or ABS rotor damaged?
YES: Replace it and then go to Step 9.
NO: Go to Step 8.
STEP 8. Check the wheel bearing.
Q: Is the wheel bearing damaged?
YES: Replace it and then go to Step 9.
NO: Go to Step 9.
STEP 9. Check the diagnostic trouble codes.
Q: Do the diagnostic trouble codes 11, 12, 13, 14, 21, 22, 23 and 24 reset?
YES: Go to Step 1.
NO: This diagnosis is complete.