ID Codes Registration Procedure

ID CODES REGISTRATION PROCEDURE

By operating the M.U.T.-III, the ID code registration and antenna communication can be performed.

CAUTION: If registered, starting the engine by using the conventional key becomes impossible. The new key will not be able to start the engine, too, because it has a different key groove.

SUPPLY UNIT LIST FOR INDIVIDUAL KEY






KEY SUPPLY UNIT LIST FOR OTHER THAN INDIVIDUAL KEY






NOTE:
- When re-registering the key (key ID), all the keys (key ID) registered before must be re-registered because all of them will be erased.
- When the key was replaced by the full service key set or when the key was replaced by the handle lock service key set separately, register the key (key ID) using the barcode No. attached to the key.
- After the key and keyless operation key is registered, start the engine with all the keys and keyless operation keys, and check that KOS operates normally.

Screen Flow Of M.U.T.-III:

Connect the M.U.T.-III to the 16-pin data link connector as follows.

NOTE: For details on how to use the scan tool, refer to the "M.U.T.-III User's Manual".

1. Start the M.U.T.-III system on the PC and turn the ignition switch to the "ON" position.






2. Select "KOS/IMMO/Keyless/TPMS" button from the "System Select" screen. Then, select the applicable option code item and push the OK button.
3. Select "Special Function" on the next screen.






4. Select the button of the operation to be performed from the "Special Function" screen.
- "Key & KOS Key Reg.": When the keyless operation key or emergency key is replaced or added as a single unit, when the emergency key is replaced or added by a supply of service key assembly.
- "Key(Barcode No.) & KOS Key Reg.": When the emergency key is replaced by the full service key set or the handle lock service key set is replaced by the piece.
- "ENG key code Reg.": When the engine control module is replaced.
- "Steering lock unit Reg.": When KOS-ECU is replaced but the steering lock assembly is not replaced.
- "Comm. Test": When the KOS antenna communication status is checked.
- "Tire Pressure Sensor ID Registration": When the TPMS transmitter is replaced.
- "Tire Pressure Sensor Check": When the tire pressure sensor data is checked.
- "Tire Pressure Sensor ID Check": When the tire pressure sensor ID is checked.

NOTE:
- For "Key Code Registration, " Refer to General (Body and Chassis) - Precautions before Service.
- For "Tire Pressure Sensor ID Registration," refer to Wireless Control Module (WCM)
- For "Tire Pressure Sensor Check," refer to Keyless Operation System
- For "Tire Pressure Sensor ID Check," refer to Scan Tool Testing and Procedures

"KEY & KOS KEY REG." METHOD






1. When "Key & KOS Key Registration" screen is displayed, enter the password for the key registration and press the OK button. Then, "Executing!" is displayed and the key registration process starts.

NOTE:
- If the wrong password is entered consecutively 5 times, the password entry for the key registration will be disabled for 16 minutes.
- The key registration cannot be cancelled during the operation.









2. When the key registration is completed, "Completed." is displayed. To continue the key registration, press the OK button according to the screen instructions. Then "Executing!" is displayed again and the next registration process starts. To finish the key registration and start the keyless operation key registration, press the cancel button. Then "Press OK button to start KOS key registration" is displayed.

NOTE:
- In order to register another key consecutively after registering the first key, the ignition switch must be turned to the ON position with the second key within 30 seconds after turning it to the "LOCK" (OFF) position with the first key.
- Up to eight keys can be registered.

3. Press the lock switch of the keyless operation key to be registered twice within 1 minute to allow the keyless operation key to be registered. Complete the registration within 1 minute and press the OK button. Then the keyless operation key registration ends.

NOTE:
- Up to 4 keyless operation keys can be registered.
- Register keyless operation keys inside the vehicle.
- Register the keyless operation keys with the key released from M.U. T.-III display.






- Push the OK button after "KOS key Registration was finished." is displayed.






- Check the number of the registered keys and keyless operation keys.

"KEY(BARCODE NO.) & KOS KEY REG." METHOD






1. When "Key (Barcode No.) & KOS key Registration" screen is displayed, enter the password for the key registration and press the OK button.

NOTE: If the wrong password is entered consecutively 5 times, the password entry for the key registration will be disabled for 16 minutes.









2. Follow the message on the screen and enter the Barcode No. Then, press the OK button.






3. "Key Registration was completed. Follow up with KOS key Registration. " is displayed, press the OK button and go to the keyless operation key registration.






4. Enter the password for keyless operation key registration and press the OK button. Then the keyless operation key registration starts.






Press the lock switch of the keyless operation key to be registered twice within 1 minute to allow the keyless operation key to be registered. Complete the registration within 1 minute and press the OK button. Then the keyless operation key registration ends.

NOTE:
- Up to 4 keyless operation keys can be registered. Register keyless operation keys inside the vehicle.
- Register the keyless operation keys with the key released from M.U.T.-III display.

6. Push the OK button after "KOS key Registration was finished." is displayed.
7. Check the number of the registered keys and keyless operation keys.

"STEERING LOCK UNIT REG." METHOD






1. Enter the password on "Steering Lock Unit Registration" screen and press the OK button to register the KOS ID.
2. Push the OK button after "Completed." is displayed.

"COMM. TEST" METHOD






1. Select the antenna to be tested on "Communication Test" screen, and press the OK button with the keyless operation key placed within the communication operational area.
2. Push the OK button after "Communication is normal." is displayed.