Transfer Case Indicator Lamp
SHIFT INDICATOR (TRANSFER CASE)4WD INDICATOR
A 4WD indicator is standard equipment on all instrument clusters. However, on vehicles not equipped with the optional four-wheel drive system and electronically shifted transfer case, this indicator is electronically disabled. The 4WD indicator is located below the minor gauge set on the left side of the cluster.
The 4WD indicator consists of a stencil-like cutout of the text 4WD in the opaque layer of the instrument cluster overlay. The dark outer layer of the overlay prevents the indicator from being clearly visible when it is not illuminated. An amber Light Emitting Diode (LED) behind the cutout in the opaque layer of the overlay causes the indicator to appear in amber through the translucent outer layer of the overlay when it is illuminated from behind by the LED, which is soldered onto the instrument cluster electronic circuit board.
When the exterior lighting is turned ON, the illumination intensity of the 4WD indicator is dimmable, which is adjusted along with the cluster general illumination lighting using the panel lamps dimmer thumbwheel on the headlamp switch.
The 4WD indicator is serviced as a unit with the instrument cluster.
4WD LOW INDICATOR
A 4WD low indicator is standard equipment on all instrument clusters. However, on vehicles not equipped with the optional four-wheel drive system and electronically shifted transfer case, this indicator is electronically disabled. The 4WD low indicator is located below the minor gauge set on the left side of the cluster.
The 4WD low indicator consists of a stencil-like cutout of the text 4LOW in the opaque layer of the instrument cluster overlay. The dark outer layer of the overlay prevents the indicator from being clearly visible when it is not illuminated. An amber Light Emitting Diode (LED) behind the cutout in the opaque layer of the overlay causes the indicator to appear in amber through the translucent outer layer of the overlay when it is illuminated from behind by the LED, which is soldered onto the instrument cluster electronic circuit board.
When the exterior lighting is turned ON, the illumination intensity of the 4WD low indicator is dimmable, which is adjusted along with the cluster general illumination lighting using the panel lamps dimmer thumbwheel on the headlamp switch.
The 4WD low indicator is serviced as a unit with the instrument cluster.
4WD INDICATOR
The 4WD indicator gives an indication to the vehicle operator when the electronic transfer case has been shifted into a 4WD mode. This indicator is controlled by a transistor on the instrument cluster circuit board based upon cluster programming and electronic messages received by the cluster from the Front Control Module (FCM) (also known as the Integrated Power Module/IPM) over the Controller Area Network (CAN) data bus.
The 4WD indicator Light Emitting Diode (LED) is completely controlled by the instrument cluster logic circuit, and that logic will only allow this indicator to operate when the instrument cluster receives a battery current input on the fused ignition switch output (run-start) circuit. Therefore, the LED will always be OFF when the ignition switch is in any position except ON or START. The LED only illuminates when it is provided a path to ground by the instrument cluster transistor. The instrument cluster will turn ON the 4WD indicator for the following reasons:
- 4WD Indicator Lamp-On Message - Each time the cluster receives an electronic 4WD indicator lamp-ON message from the FCM, the indicator will be illuminated. The indicator remains illuminated until the cluster receives a lamp-OFF message from the FCM, or until the ignition switch is turned to the OFF position, whichever occurs first.
- Actuator Test - Each time the cluster is put through the actuator test, the 4WD indicator will be turned ON, then OFF again during the bulb check portion of the test to confirm the functionality of the LED and the cluster control circuitry.
The FCM continually monitors the electronic transfer case through the transfer case shift motor/mode sensor assembly to determine when the 4WD mode is engaged. The FCM then sends the proper lamp-ON or lamp-OFF message to the ElectroMechanical Instrument Cluster (EMIC) (also known as the Cab Compartment Node/CCN).
For proper diagnosis of the transfer case shift motor/ mode sensor, the FCM, the EMIC, the CAN data bus or the electronic communication related to 4WD indicator operation a diagnostic scan tool is required. Refer to the appropriate diagnostic information.
4WD LOW INDICATOR
The 4WD low indicator gives an indication to the vehicle operator when the electronic transfer case has been shifted into the 4WD low mode. This indicator is controlled by a transistor on the instrument cluster circuit board based upon cluster programming and electronic messages received by the cluster from the Front Control Module (FCM) (also known as the Integrated Power Module/IPM) over the Controller Area Network (CAN) data bus.
The 4WD low indicator Light Emitting Diode (LED) is completely controlled by the instrument cluster logic circuit, and that logic will only allow this indicator to operate when the instrument cluster receives a battery current input on the fused ignition switch output (run-start) circuit. Therefore, the LED will always be OFF when the ignition switch is in any position except ON or START. The LED only illuminates when it is provided a path to ground by the instrument cluster transistor. The instrument cluster will turn ON the 4WD low indicator for the following reasons:
- 4WD Low Indicator Lamp-On Message - Each time the cluster receives an electronic 4WD low indicator lamp-ON message from the FCM, the indicator will be illuminated. The indicator remains illuminated until the cluster receives a lamp-OFF message from the FCM, or until the ignition switch is turned to the OFF position, whichever occurs first.
- Actuator Test - Each time the cluster is put through the actuator test, the 4WD low indicator will be turned ON, then OFF again during the LED portion of the test to confirm the functionality of the LED and the cluster control circuitry.
The FCM continually monitors the electronic transfer case through the transfer case shift motor/mode sensor assembly to determine when the 4WD low mode is engaged. The FCM then sends the proper lamp- ON or lamp-OFF message to the ElectroMechanical Instrument Cluster (EMIC) (also known as the Cab Compartment Node/CCN).
For proper diagnosis of the transfer case shift motor/ mode sensor, the FCM, the EMIC, the CAN data bus or the electronic communication related to 4WD low indicator operation a diagnostic scan tool is required. Refer to the appropriate diagnostic information.