Inspection Procedure 3 [Vehicles Without Audio Amplifier]
INSPECTION PROCEDURE 3: No sound is heard from one of the speakers. [Vehicles without audio amplifier]
CAUTION:
Before replacing the radio and CD player, ensure that the power supply circuit, the ground circuit and the communication circuit are normal.
COMMENTS ON TROUBLE SYMPTOM
If the sound is not output from one of the speakers, the speaker, radio and CD player, communication line from the radio and CD player to the speakers may have a problem.
PROBABLE CAUSES
- Malfunction of speaker
- Malfunctions of radio and CD player
- Damaged harness wires and connectors
DIAGNOSIS
Required Special Tools:
- MB991223: Harness Set
- MB992006: Extra Fine Probe
- MB991958: Scan Tool (M.U.T.-III Sub Assembly)
- MB991824: Vehicle Communication Interface (V.C.I.)
- MB991827: M.U.T.-III USB Cable
- MB991910: M.U.T.-III Main Harness A
STEP 1. ETACS-ECU coding data check.
(1)Operate the scan tool to read the ETACS-ECU option coding information. Programming and Relearning.)
(2)Check that the "Number of speaker" is set to "6 speakers".
Q. Is the check result normal?
YES Go to Step 2.
NO Operate the scan tool to set the option coding "Number of speaker" to "6 speakers", and check the trouble symptom.
STEP 2. Checking with speaker test.
Perform the speaker test, and check which speaker does not output the sound. Refer to Testing and Inspection.
Q. Is the check result normal?
YES [normal for all] : The trouble can be an intermittent malfunction How to Cope With Intermittent Malfunctions).
NO [abnormal for all] : Go to Step 27.
NO [only front door speaker (RH) is abnormal] : Go to Step 3.
NO [only front door speaker (LH) is abnormal] : Go to Step 7.
NO [only rear door speaker (RH) is abnormal] : Go to Step 11.
NO [only rear door speaker (LH) is abnormal] : Go to Step 15.
NO [only tweeter (RH) vehicles with 6 speakers is abnormal] : Go to Step 19.
NO [only tweeter (LH) vehicles with 6 speakers is abnormal] : Go to Step 23.
STEP 3. Check front door speaker (RH) connector E-04 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q. Is front door speaker (RH) connector E-04 in good condition?
YES Go to Step 4.
NO Repair or replace the damaged component(s). Harness Connector Inspection.
STEP 4. Front door speaker (RH) check.
(1)Remove the front door speaker (RH). Refer to Service and Repair.
(2)Check that the front door speaker (RH) outputs the noise when the voltage of five volts is applied to the front door speaker (RH) connector terminal.
Q. Does the front door speaker (RH) output the noise?
YES Go to Step 5.
NO Replace the front door speaker (RH).
STEP 5. Check radio and CD player connector C-16 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q. Is radio and CD player connector C-16 in good condition?
YES Go to Step 6.
NO Repair or replace the damaged component(s). Harness Connector Inspection.
STEP 6. Check the wiring harness between radio and CD player connector C-16 (terminal 26, 36) and front door speaker (RH) connector E-04 (terminal 1, 2).
NOTE:
Also check intermediate connector C-112 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector C-112 is damaged, repair or replace the connector as described in Harness Connector Inspection Harness Connector Inspection.
- Check the communication lines for open circuit and short circuit.
Q. Is the wiring harness between radio and CD player connector C-16 (terminal 26, 36) and front door speaker (RH) connector E-04 (terminal 1, 2) in good condition?
YES Check the trouble symptom. Go to Step 27.
NO The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary.
STEP 7. Check front door speaker (LH) connector E-17 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q. Is front door speaker (LH) connector E-17 in good condition?
YES Go to Step 8.
NO Repair or replace the damaged component(s). Harness Connector Inspection.
STEP 8. Front door speaker (LH) check.
(1)Remove the front door speaker (LH). Refer to Service and Repair.
(2)Check that the front door speaker (LH) outputs the noise when the voltage of five volts is applied to the front door speaker (LH) connector terminal.
Q. Does the front door speaker (LH) output the noise?
YES Go to Step 9.
NO Replace the front door speaker (LH).
STEP 9. Check radio and CD player connector C-16 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q. Is radio and CD player connector C-16 in good condition?
YES Go to Step 10.
NO Repair or replace the damaged component(s). Harness Connector Inspection.
STEP 10. Check the wiring harness between radio and CD player connector C-16 (terminal 28, 38) and front door speaker (LH) connector E-17 (terminal 1, 2).
NOTE:
Also check intermediate connector C-126 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector C-126 is damaged, repair or replace the connector as described in Harness Connector Inspection Harness Connector Inspection.
- Check the communication lines for open circuit and short circuit.
Q. Is the wiring harness between radio and CD player connector C-16 (terminal 28, 38) and front door speaker (LH) connector E-17 (terminal 1, 2) in good condition?
YES Check the trouble symptom. Go to Step 27.
NO The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary.
STEP 11. Check rear door speaker (RH) connector E-10 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q. Is rear door speaker (RH) connector E-10 in good condition?
YES Go to Step 12.
NO Repair or replace the damaged component(s). Harness Connector Inspection.
STEP 12. Rear door speaker (RH) check
(1)Remove the rear door speaker (RH). Refer to Service and Repair.
(2)Check that the rear door speaker (RH) outputs the noise when the voltage of five volts is applied to the rear door speaker (RH) connector terminal.
Q. Does the rear door speaker (RH) output the noise?
YES Go to Step 13.
NO Replace the rear door speaker (RH).
STEP 13. Check radio and CD player connector C-16 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q. Is radio and CD player connector C-16 in good condition?
YES Go to Step 14.
NO Repair or replace the damaged component(s). Harness Connector Inspection.
STEP 14. Check the wiring harness between radio and CD player connector C-16 (terminal 25, 35) and rear door speaker (RH) connector E-10 (terminal 1, 2).
NOTE:
Also check intermediate connectors C-20 and D-36 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector C-20 or D-36 is damaged, repair or replace the connector as described in Harness Connector Inspection Harness Connector Inspection.
- Check the communication lines for open circuit and short circuit.
Q. Is the wiring harness between radio and CD player connector C-16 (terminal 25, 35) and rear door speaker (RH) connector E-10 (terminal 1, 2) in good condition?
YES Check the trouble symptom. Go to Step 27.
NO The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary.
STEP 15. Check rear door speaker (LH) connector E-24 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q. Is rear door speaker (LH) connector E-24 in good condition?
YES Go to Step 16.
NO Repair or replace the damaged component(s). Harness Connector Inspection.
STEP 16. Rear door speaker (LH) check.
(1)Remove the rear door speaker (LH). Refer to Service and Repair.
(2)Check that the rear door speaker (LH) outputs the noise when the voltage of five volts is applied to the rear door speaker (LH) connector terminal.
Q. Does the rear door speaker (LH) output the noise?
YES Go to Step 17.
NO Replace the rear door speaker (LH).
STEP 17. Check radio and CD player connector C-16 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q. Is radio and CD player connector C-16 in good condition?
YES Go to Step 18.
NO Repair or replace the damaged component(s). Harness Connector Inspection.
STEP 18. Check the wiring harness between radio and CD player connector C-16 (terminal 27, 37) and rear door speaker (LH) connector E-24 (terminal 1, 2).
NOTE:
Also check intermediate connectors C-32 and D-21 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector C-32 or D-21 is damaged, repair or replace the connector as described in Harness Connector Inspection Harness Connector Inspection.
- Check the communication lines for open circuit and short circuit.
Q. Is the wiring harness between radio and CD player connector C-16 (terminal 27, 37) and rear door speaker (LH) connector E-24 (terminal 1, 2) in good condition?
YES Check the trouble symptom. Go to Step 27.
NO The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary.
STEP 19. Check tweeter (RH) connector E-02 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q. Is tweeter (RH) connector E-02 in good condition?
YES Go to Step 20.
NO Repair or replace the damaged component(s). Harness Connector Inspection.
STEP 20. Tweeter (RH) check.
(1)Remove the tweeter (RH). Refer to Service and Repair.
(2)Check that the tweeter (RH) outputs the noise when the voltage of five volts is applied to the tweeter (RH) connector terminal.
Q. Does the tweeter (RH) output the noise?
YES Go to Step 21.
NO Replace the tweeter (RH).
STEP 21. Check radio and CD player connector C-16 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q. Is radio and CD player connector C-16 in good condition?
YES Go to Step 22.
NO Repair or replace the damaged component(s). Harness Connector Inspection.
STEP 22. Check the wiring harness between radio and CD player connector C-16 (terminal 26, 36) and tweeter (RH) connector E-02 (terminal 2, 1).
NOTE:
Also check intermediate connector C-113 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector C-113 is damaged, repair or replace the connector as described in Harness Connector Inspection Harness Connector Inspection.
- Check the communication lines for open circuit and short circuit.
Q. Is the wiring harness between radio and CD player connector C-16 (terminal 26, 36) and tweeter (RH) connector E-02 (terminal 2, 1) in good condition?
YES Check the trouble symptom. Go to Step 27.
NO The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary.
STEP 23. Check tweeter (LH) connector E-14 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q. Is tweeter (LH) connector E-14 in good condition?
YES Go to Step 24.
NO Repair or replace the damaged component(s). Harness Connector Inspection.
STEP 24. Tweeter (LH) check.
(1)Remove the tweeter (LH). Refer to Service and Repair.
(2)Check that the tweeter (LH) outputs the noise when the voltage of five volts is applied to the tweeter (LH) connector terminal.
Q. Does the tweeter (LH) output the noise?
YES Go to Step 25.
NO Replace the tweeter (LH).
STEP 25. Check radio and CD player connector C-16 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q. Is radio and CD player connector C-16 in good condition?
YES Go to Step 26.
NO Repair or replace the damaged component(s). Harness Connector Inspection.
STEP 26. Check the wiring harness between radio and CD player connector C-16 (terminal 28, 38) and tweeter (LH) connector E-14 (terminal 2, 1).
NOTE:
Also check intermediate connector C-127 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector C-127 is damaged, repair or replace the connector as described in Harness Connector Inspection Harness Connector Inspection.
- Check the communication lines for open circuit and short circuit.
Q. Is the wiring harness between radio and CD player or CD changer connector C-16 (terminal 28, 38) and tweeter (LH) connector E-14 (terminal 2, 1) in good condition?
YES Check the trouble symptom. Go to Step 27.
NO The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary.
STEP 27. Retest the system
Check if the sound is output from the speakers.
Q. Is the check result normal?
YES The trouble can be an intermittent malfunction How to Cope With Intermittent Malfunctions).
NO Replace the radio and CD player.