Recall - Power Window Module Replacement
POWER WINDOW EXPRESS-DOWN MODULENumber:
91-C-07
Date:
April 1992
Section:
10
Subject:
POWER WINDOW EXPRESS-DOWN MODULE
Models/Years:
CERTAIN 1991 OLDSMOBILE CUTLASS CALAIS MODELS EQUIPPED WITH POWER WINDOWS (RPO A31)
CONDITION
General Motors has determined that a defect which relates to motor vehicle safety exists in certain 1991 Oldsmobile Cutlass Calais model vehicles equipped with power windows (RPO A31). These vehicles may exhibit a condition in which moisture enters the express-down electronic control module and creates undesirable continuity. This may result in window operation without operator input and could cause the window to remain down. The module may eventually fail by overheating, which could result in a fire in the door panel area.
To prevent this condition from occurring, dealers are to replace the power window express-down electronic control module.
VEHICLES INVOLVED
Certain 1991 Oldsmobile Cutlass Calais model vehicles EQUIPPED WITH POWER WINDOWS (RPO A31) within the breakpoints listed below:
Beginning Through &
Year Model Model Name VIN lncluding
1991 N Cutlass Calais MM040569 MM075400
NOTICE:
Only 12% of the vehicles between the breakpoints are equipped with power windows.
DEALER ACTION
Dealers are to perform this campaign on all involved vehicles at no charge to owners, regardless of mileage, age of vehicle, or ownership from this time forward.
Whenever a vehicle subject to this campaign is taken into your new or used car inventory, or it is in your dealership for service, you are to ensure the campaign correction has been made before selling or releasing the vehicle.
Dealers are to contact owners of vehicles recently sold from your new or used vehicle inventory and arrange for the campaign correction to be performed.
SERVICE PROCEDURE
NOTICE:
MAKE SURE THE IGNITION IS IN THE "OFF" POSITION AND THE KEY IS REMOVED FROM THE IGNITION BEFORE DISCONNECTING OR CONNECTING POWER WINDOW SWITCHES. FAILURE TO DO SO COULD RESULT IN DAMAGE TO THE POWER WINDOW SWITCHES.
1. Position the door glass in full down position and remove door trim panel following the procedure in section 10-6 of the 1991 Oldsmobile Cutlass Calais Service Manual.
2. Carefully peel the water deflector upward and rearward far enough to completely uncover the access hole at the front of the door inner panel. Use care to avoid damaging the water deflector.
CAUTION:
MAKE SURE THAT THE IGNITION IS IN THE "OFF" POSITION AND THE KEY IS REMOVED FROM THE IGNITION WHILE WORKING INSIDE THE DRIVER'S DOOR. WHEN OPERATED, THE EXPRESS DOWN FEATURE ALLOWS THE DOOR GLASS TO DROP VERY QUICKLY WHICH COULD CAUSE PERSONAL INJURY.
3. Disconnect the express down module wiring connector. See Illustration.
4. Depress the release tab on the lower edge of the express down module and pull the module toward the front of the vehicle. The module will move about 3/8 inch before the mounting stud on the module contacts the front of the slot in the mounting bracket. Disengage the module from the mounting bracket by tilting the module outward (away from the inner door). See the Illustration.
5. Install the new express down module, P/N 16626458, by positioning the module to the mounting bracket and sliding into position until the release tab locks into position.
6. Reconnect the wiring connector to the express down module.
7. Reposition the water deflector to the door inner panel. Water proof tape must be used to reseal the deflector if the original adhesive becomes loose, if the holes in the deflector do not line up with the door inner panel, or if the deflector is damaged.
8. Reinstall the door trim panel following the procedure in section 10-6 of the service manual.
9. Check the window for proper operation. Then install a Campaign Identification Label.
CAMPAIGN IDENTIFICATION LABEL
Each label provides space to print the campaign number, and the five (5) digit dealer code of the dealer performing the campaign. Insert this information with a typewriter or ball-point pen. When installing label, clean and dry the surface of the radiator support tie bar and apply the campaign label where it is readily visible.
PARTS INFORMATION
To ensure that the parts your dealership may require are obtained as soon as possible, order them from GM Service Parts Operations (GMSPO) on a C.I.O. order, with NO special instruction code, but order on an advise code (2). Use the following part number:
Description Part Number Quantity Per Vehicle
Module, P/W Cont 16626458 1
(Some parts may include a mounting bracket, which may be removed and discarded prior to installation)
WARRANTY CLAIM INFORMATION
Submit claims using only one of the labor-ops below for each vehicle:
REPAIR PERFORMED TOT-PTS FC LAB-0P LHRS ST
Replace Express Down Module 96 V7340 .6 .1*
* .1 hour for clerical administration may be applied for in the Straight Time (ST) column.
Parts Allowance:
Current dealer price, plus 30% allowance for handling.