Flushing (V-5)
FLUSHING (V-5)TOOLS REQUIRED
- J 43600 ACR 2000 Air Conditioning Service Center
- J 45268 Flush Adapter Kit
- J 41447 Leak Detection Dye
- J 41459 Leak Detection Dye Injector
- J 42220 Universal 12V Leak Detection Lamp
IMPORTANT: Flushing with the ACR 2000 is not intended to remove metal from the A/C system.
Flushing is intended to remove the following contaminants:
- Contaminated PAG oil
- Desiccant, following a desiccant bag failure
- Overcharge of PAG oil
- Refrigerant contamination
1. Recover the refrigerant.
IMPORTANT: Warmer engine or ambient temperature decreases the refrigerant recovery time during the A/C flush procedure.
2. Remove the orifice tube.
3. Connect the A/C lines with the orifice tube removed.
4. Remove the A/C compressor.
5. Install J 45268-3 to the A/C compressor hose assembly.
6. Forward flow refrigerant flushing is recommended for contaminated refrigerant or PAG oil.
Perform the following procedure:
6.1. Service the filter with AC Delco P/N GF 470, before each flush.
Connect J 45268-1 flush filter to the suction port of J 45268-3 flush adapter.
IMPORTANT: The filter inside J 45268-1 is serviceable. Remove and discard the check valve from the filter.
6.2. Connect the blue hose from J 43600 to J 45268-1 flush filter adapter.
6.3. Connect the red hose from J 43600 to J 45268-3.
7. Reverse flow refrigerant flushing is recommended for desiccant bag failure only. Perform the following procedure and replace the accumulator when the flush is complete:
7.1. Service the filter with ACDelco P/N GF 470, before each flush.
IMPORTANT: The filter inside J 45268-1 is serviceable. Remove and discard the check valve from the filter.
7.2. Connect J 45268-1 flush filter to the discharge port of J 45268-3 flush adapter.
7.3. Connect the blue hose from J 43600 to J 45268-1 flush filter adapter.
7.4. Connect the red hose from J 43600 to the suction port of J 45268-3.
8. Flush the A/C system. Follow the instructions supplied with the J 43600.
IMPORTANT: Close the valve on the external refrigerant tank, before starting the flush process.
9. Remove J 45268-3 from the A/C compressor hose assembly.
10. If reinstalling the removed A/C compressor, perform the following procedure:
10.1. Remove the A/C compressor drain plug.
10.2. Drain the PAG oil from the A/C compressor. Rotate the compressor input shaft to assist in draining the PAG oil from the compressor.
10.3. Install the A/C compressor drain plug.
NOTE: Refer to Fastener Notice in Service Precautions.
IMPORTANT: Flushing will remove all the PAG oil from the A/C system.
The A/C system must be replenished with the correct amount of PAG oil. If replacing the A/C compressor after flushing the system, add the total system capacity of PAG oil to the compressor.
Tighten
Tighten the drain plug to 20 N.m (15 lb ft).
10.4. Add the total system capacity of PAG oil to the A/C compressor.
11. Install the A/C compressor.
12. Inspect the orifice tube for debris. Clean or replace as needed.
13. Install the orifice tube.
14. Evacuate and recharge the A/C system.
15. Add one bottle of J 41447 using J 41459.
IMPORTANT: Flushing will remove the fluorescent leak detection dye from the A/C system.
16. Leak test the fittings using J 42220.