Teaching Hand-held Transmitter
Teaching hand-held transmitter
General
Up to four hand-held transmitters can be adapted to the control module. The hand-held transmitter is used for operating the central locking system. Another function is the Immobilizer by means of the integrated transponder coil.
Work preparation
The following information is required to teach the hand-held transmitter:
- Key learning code from IPAS
- 24 digit Code No. (see barcode label on key grip)
- If the key is stolen or the hand-held transmitter is faulty, all keys still in the customer's possession will be required.
NOTE: During maintenance work, please bear In mind that the transmission frequency of the hand-held transmitter is different according to the country of use. The corresponding reception frequency is printed on the alarm system control module. This reception frequency is either:
433 MHz with M-number M534
or
315 MHz with M-number M535
Procedure
1. Connect the vehicle keys and the new hand-held transmitter and insert in the ignition.
2. Connect PST 2 and switch on ignition.
3. Select Alarm system in the menu and press the double arrow key[ >>].
4. Select Learning function in the menu and press the double arrow key [>>].
5. Select menu item Transponder key and press the double arrow key[ >>].
6. The following message appears on the screen: "Input key learning code". With the arrow keys [Up arrow] or [Down arrow], input the key learning code and press the double arrow key [>>].
7. The following message appears on the screen: "Please confirm input". Check the input and press the [F7] key to confirm the input.
8. Distinguish between loss and fault and additional hand-held transmitter for the transponder.
a) Teaching an additional hand-held transmitter
With the arrow key [v] select a free position (1, 2, 3 or 4) and press the [F8] key.
Now the transponder code is saved in the selected position. Note the position of the new transponder code.
b) Teaching in the case of a lost or faulty hand held transmitter:
CAUTION
Risk of theft due to the lost hand-held transmitter
> It is essential to identify and delete the transponder code of the lost hand-held transmitter as described in step 8 b).
> It is essential to identify and delete the radio code of the lost hand-held transmitter as described in step 12 b).
In this case, it is first necessary to identify and delete the stored transponder code of the lost hand-held transmitter. The remaining vehicle keys are required for this purpose. One after the other, insert the keys into the ignition lock, switch the ignition on and establish communication with the control module. Current transponder shows the transponder code of the vehicle key that is presently inserted in the ignition lock. Compare this transponder code with the transponder codes at positions 1 to 4. This comparison allows The position of the lost hand-held transmitter (Transponder code) to be identified, as one transponder code is ultimately left over at positions 1 to 4. Insert the vehicle key equipped with the new bane-held transmitter into the ignition lock and switch on the ignition. Establish communication between the PST2 and the control module. Select the identified position using the arrow keys [Up arrow] and. [Down arrow], then delete the transponder code with key [F3]. Then press the [F8] key.
9. Press the double arrow key [<<], select menu item Remote controf and press the double arrow key [>>]
10. "Input key learning code" appears on the screen. With the arrow keys [Up arrow] or [Down arrow]. input the key learning code and press the double arrow key [>>].
11. The following message appears on the screen: "Please confirm input". Check the input and press the [F7] key to confirm the input.
12. Distinguish between loss and fault and additional hand-held transmitter for the radio code.
a) Teaching an additional hand-held transmitter
Select the same position (1 to 4) as for the transponder key and press the [F8] key.
b) Teaching in the case of a lost or faulty hand-held transmitter:
In this case, it is first necessary to identify and delete the stored "radio code" of the lost hand-held transmitter. The remaining hand- held transmitters are required for this purpose. Press the locking button on the hand-held transmitter and then insert the vehicle key into the ignition lock, switch on the ignition and re-establish communication with the control module. Current radio key shows the "radio code" of the vehicle key that is presently inserted in the ignition lock.
Compare this radio code with the radio codes at positions 1 to 4. This comparison allows the position of the lost hand-held transmitter (radio code) to be identified, as one "radio code" is ultimately left over at positions 1 to 4.
Insert the vehicle key equipped with the new hand-held transmitter into the ignition lock and switch on the ignition. Establish communication with the control module. Select the identified position using the arrow keys [Up arrow] and. [Down arrow], then delete the radio code with key [F3]. Then press the [F8] key.
13. Carefully input the 24 digit code number with the arrow keys [Up arrow] or [Down arrow] and press the double arrow key [>>].
14. The following message appears on the screen: "Please confirm input". Check the input and press the [F7] key.
15. Now the hand-held transmitter is taught. Go back to the menu item Learning function, remove the key and switch on the ignition again. Once the key has been removed again, the hand-held transmitter is ready for use. Check hand-held transmitter for operation.