M96/21 and M96/22 With Manual Transmission
Removing Engine M96/21 (3.2 l) and M96/22 (2.7 l) With Manual Transmission
Engine, M96/21 (3.2 l) and M96/22 (2.7 l)
Special Tools
Adjusting Tool
NOTE: If the special tool 9592 is being used for the first time, (four) additional threaded holes must be applied.
1. Lay the support plate 9592/1 on the rear of the retainer plate 9592 and fasten with four hexagon-head bolts M8 x 25.
2. Countersink the retainer plate at the designated bores -arrows- with a 9 mm drill bit. The support plate serves as the drilling template.
3. Drill through the countersunk bores on the retainer plate with a drill bit sized 6.8 mm and then cut an M8 thread.
4. Fasten the special tool adapter 9163/2 with a hexagon-head bolt M8 x 25 (bolt quality 10.9) and hexagon-head bolts M8 x 16 (bolt quality 10.9) at the designated position "Boxster". The adapter and the support plate are fastened on the retainer plate with the M8 x 25 hexagon-head bolts. The M8 x 16 hexagon head bolts connect the adapter with the support plate.
5. Support for Tiptronic transmission with three M6 x 20 (2 ea.) and M8 x 25 (1 ea.) wood screws.
Drawing shows complete engine retainer plate fitted on the workshop jack.
6. Fit complete retainer plate on the workshop jack.
Removing Engine
NOTE: The engine is removed downwards complete with the manual transmission.
1. Position the vehicle at the specified points on a lifting platform.
2. Open both the luggage compartment lids.
3. Cover the vehicle. Cover the vehicle with protective covers in such a way that the body can not be damaged.
4. Move convertible top or convertible-top compartment lid to service position. Open the convertible top until the convertible-top compartment lid is half open.
5. Detaching cloth covering. Disengage the rear strip on the left and right sides of the cloth covering in downward direction.
6. Detach tension cables. Press the ball socket of the tension cable out of the ball head of the adjusting piece on the left and right.
7. Move convertible top to service position. To do so, press the tension bow of the convertible top towards the main bow, until it reaches its locking point.
8. Move the convertible-top compartment lid to service position and secure. Disengage the convertible-top compartment links at the extreme bottom. To do so, disengage the clips at the left and right and pull the links off the bolt.
9. Press the convertible-top compartment links forwards until the two bores coincide and a 5 mm mandrel can be pushed through them.
10. Remove left-hand seat. For better accessibility, remove the left-hand seat of the car. Unscrew the four internal-serration screws, disconnect all the electrical plug connections and remove the seat.
11. Open the rear wall cover. To do so, remove the oddments tray behind the seats and remove the rear wall lining. Then undo the 6 fastening screws and the 2 fastening nuts -arrows-.
CAUTION:
Danger of short circuit!
First remove the ground terminal.
Cover the terminals.
Never connect (short circuit) the terminals.
12. Disconnect battery. Before disconnecting, find out the relevant theft codes (e.g. radio) if necessary. At the battery, disconnect the ground terminal and remove the ground cable.
13. Remove the rear spoiler.
14. Remove rear bumper. While doing so, pay attention to the connection for the number plate lighting.
15. Remove left and right wheel housing trims.
16. Remove the rear part of the underbody cover.
17. Lift the vehicle. Before lifting, check that all fastening points of the diagonal braces are easily accessible. Pay particular attention to the threaded part -C-.
18. Undo the fastening screw -C- and the collar nuts -D- and remove the diagonal braces -B- together with the holder -E-.
19. Remove stabilizer.
20. To do so, unscrew the two fastening screws at each of the two bearing surfaces on the left and right.
21. Unscrew the stabilizer on the left and right of the links.
22. Detach rear cross member (aluminium V-member) on the body.
23. Undo the cable. Undo the engine cable on the rear-axle support. The cable must be countered with a suitable wrench and must not be twisted.
24. Undo halfshafts. To do so, undo the fastening screws of the halfshafts on the transmission. Fit protection on to the halfshafts.
25. Unclip and detach the oxygen sensor plug connection from the holders of the rear-axle support. On an OBDII vehicle, additionally disconnect the oxygen sensor plug connection in the rear wing area. Press the heat shield aside and disconnect the plugs.
26. Remove rear mufflers. To do so, secure the rear mufflers with a transmission jack. Then undo the flange connection between the catalytic converters and the exhaust manifold. Undo the three hexagon-head bolts on the exhaust bracket.
NOTE:
- When lowering, do not damage the oxygen sensors, cables and plugs.
- Attach protective sleeves around the oxygen sensor plugs.
View of the support
27. Remove the front lining in the rear luggage compartment. Lever off plastic clips using a commercially available removal too.
28. Remove the rear-axle support. Unscrew the four fastening screws and remove the rear-axle support to one side.
29. Drain coolant. To do so, remove the screw plug of the coolant circuit on the coolant guide housing. Collect coolant in a clean container.
Open spring band clamp
Pull off the hose
30. Disconnect coolant hoses. Open the supply and return lines for coolant on the engine and pull them off. Then close all openings. Collect emerging coolant in a clean container.
CAUTION:
Danger of fire!
- Collect emerging fuel.
- Avoid ignition sources and naked flames.
31. Detach the fuel return line. Disconnect the fuel return line under the vehicle floor by pressing gently on the button and pull apart. Collect emerging fuel. Close off the open ends of the line immediately. Then open the holder on the body and remove the line.
32. Disconnect the steering lines. Remove the small undersealing on the left vehicle underside (six plastic nuts). Disconnect the two hydraulic lines of the power steering on the vehicle floor. To do so, undo the threaded part and disconnect. Any emerging Pentosin must be collected.
33. Disengage the retaining clips for the power-assisted steering lines and the brake vacuum hose and remove the lines.
34. Unscrew the heat shield on the transmission. To do so unscrew the two fastening nuts and remove the plate.
35. Disengage shift cables on the transmission. Disengage the cables with the commercially available tool.
36. Detach the shift cables. Unclip the shift cables on the transmission mount. Then pull the shift cables upwards out of the engine compartment and set them aside.
WARNING:
Risk of damage!
- When the slave cylinder is removed, do not actuate the clutch again.
37. Uncouple clutch slave cylinder. To do so, unscrew the fastening screw and remove the clutch slave cylinder. Tie the cylinder with a wire.
38. Disconnect the electric plug on the hot film mass air flow sensor. Then disconnect the connecting hose between the hot film mass air flow sensor and the throttle body. To do so, disconnect the hose clamp on the hot film mass air flow sensor.
39. Press the spring band clamp on the oil filler hose apart and push it aside. Pull off the oil filler hose; heat, if necessary.
40. Disconnect the fuel supply hose. Make sure without fail to counter with a suitable wrench when doing this. Collect emerging residual fuel. Then disconnect the ground cable.
Snap ring
Inner and outer sleeve
41. Disconnect vacuum line for the brake booster. To do so, remove the grey snap ring. Then push the inner sleeve -1- against the outer sleeve -2- and pull off both sleeves together in the direction of the arrow.
42. Disconnect B+ separator box. To do so, undo the nut in the separator box. Remove the cable and lay to one side.
43. Remove supply tank of the power steering system. To do so, suck fluid out as much as possible. Then open the bayonet lock on the bottom of the expansion tank and remove the tank. Close the opening in the servo pump with a clean plug.
NOTE:
- In vehicles with air conditioning, the points 44 to 47 must also be carried out.
- Never evacuate and open the air-conditioning circuit unless this is absolutely necessary.
44. Remove drive belt. Mark the running direction of the drive belt with a coloured pen. Slacken the belt. Slacken belt by turning the tensioning pulley (wrench size 24 mm) clockwise, hold still and simultaneously take the belt off the drive pulleys.
45. Undo the rear fastening screw of the air-conditioning compressor from above. The screw is positioned between the intake manifolds of the fifth and sixth cylinders.
46. Loosen air-conditioning compressor. To do so, undo the two front fastening screws -(arrows)-. Disconnect the electrical plug.
NOTE: The air-conditioning compressor can be removed from the vehicle more easily if the engine has already been lowered.
47. Set the air-conditioning compressor with the hoses connected to one side or lift it out of the engine compartment and set it on a suitable base.
48. Remove the rear luggage compartment lining. To do so, lever out the rear fastening clips and remove the lining from the luggage compartment.
49. Disconnect the plug connections (X3/1, X3/2 and X59) of the engine wiring harness. To do so, raise the lock at the side and pull the plug out.
50. Lock the ground point of the engine control module.
51. Unplug the engine control module. Open the topmost plug by actuating the side button and pull out. Remove the other plugs from the top down. To do so, press the locking button in and push the locking bar upwards.
52. Uncover the engine wiring harness. To do so, press the rubber sleeve on the luggage compartment rear wall inwards and guide the wiring harness towards the engine compartment, if the engine is to be lowered later.
53. Disconnect the plug connection at the guide tube of the oil dip-stick. To do so, press the two tabs together and unclip the tube.
View of the engine retainer plate
Plate positioned and secured
Car jack placed underneath
NOTE:
- It is recommended to position the complete retainer plate using a transmission jack first. Only then should the workshop car jack be placed underneath.
- The support C1 should rest against the transmission oil pan under a slight pre-load. If necessary, fit the included spacer plate.
54. Place pre-assembled engine retainer plate with transmission support on the crankcase or transmission.
CAUTION:
Risk of damage!
When undoing the multi-tooth nut, the mount is destroyed!
55. Remove the transmission support with the hydraulic mounts. Undo the two fastening nuts on the left and right.
56. Undo the front engine carrier. To do so, unscrew the four fastening nuts.
Pay attention to the VarioCam cable
57. Lower the engine-transmission unit carefully. Ensure that there is sufficient clearance for the components. The engine wiring harness must be guided during the lowering procedure.
WARNING:
Risk of damage!
Only place the vehicle on its wheels or push it after the rear-axle support, the sheetmetal brace and both the diagonal braces have been installed.