74521902 Removing and installing padding for 2/3-split folding backrest
WM 745219 Removing and installing padding for 2/3-split folding backrest
Technical values
Preliminary work
Preliminary work - Removing padding for 2/3-split folding rear backrest
1. Remove backrest: => 724719 Removing and installing rear backrest - section on "Removing"
2. Remove lock for rear backrest: => 724719 Removing and installing rear backrest - section on "Removing"
3. Remove armrest with cover (rear): => 745519 Removing and installing armrest with cover (rear) - section on "Removing"
4. Remove headrest.
Removing padding for 2/3-split folding rear backrest
Removing padding for 2/3-split folding rear backrest
1. Remove support: Undo fastening screws -2-.
2. Take off support -1- ( -Arrow A- ).
3. Removing headrest guides: Insert screwdriver (width 2 mm) from inside into bore above locking tab.
4. Press screwdriver in direction of arrow -Arrow B- and release locking tab -Arrow C-.
5. Pull out headrest guides -3- -Arrow D-.
6. Unclip seat belt cover -5- -Arrow E-.
7. Unclip safety belt cover -4- and remove it ( -Arrows F-.
8. Remove cover of loading equipment.
8.1. Remove cover of load-through provision: Fold over cover for backrest -6- -Arrow G- and pull out over the holding strap -7- -Arrow H-.
9. Detach plastic strip -8- of covering for backrest -6- on backrest frame -Arrow I-.
10. Open front lid -9- -Arrow K-.
11. Unclip cover of load-through provision -10- -circle marks- and remove -Arrow L-.
12. Detach plastic strips -8- of covering for backrest -6- -Arrows M-.
13. Detach hook -15- of covering for backrest -6- -Arrow N-.
14. Lever out piping -11- of cover for seat -6- with a plastic wedge at the upper right corner -Arrow O-.
15. Pull piping -11- of cover for backrest -6- out completely in the direction of the arrow.
16. Pull covering for backrest -6- over the pin -12- -Arrow P-.
17. Pull covering for backrest -6- over the holder for child-lock button -13- -Arrow Q-.
18. Remove backrest frame -14- from padding with cover -6- -Arrow R-.
19. Remove cover for rear backrest: => 745319 Removing and installing cover for rear backrest - section on "Removing"
Installing padding for 2/3-split folding rear backrest
1. Install cover for rear backrest: => 745319 Removing and installing cover for rear backrest - section on "Installing"
2. Install padding: Place backrest frame -14- on the padding with cover for backrest -6- and align -Arrow A-. In doing so, pull cover for backrest -6- over the holder for child-lock button -13- -Arrow C-.
3. Pull cover for backrest -6- over the pin -12- -Arrow D-.
4. Press piping -11- of cover for backrest -6- completely into the backrest frame in direction of arrow -14- -Arrow B-.
5. Engage hook -15- of covering for backrest -6- -Arrow E-.
6. Engage plastic strips -8- of covering for backrest -6- -Arrows F-.
7. Install cover of load-though provision: Insert cover of load-through provision -10- -Arrow G- and clip in -circle marks-.
8. Close front lid -9- ( -Arrow H- ).
9. Engage plastic strip -8- of cover for backrest -6- on backrest frame -Arrow I-.
Insert cover for backrest -6- over the holding strap -7- -Arrow K- and fold over -Arrow L-.
10. Insert seat belt cover -4- and clip in -Arrows M-.
11. Clip in cover -5- -Arrow N-.
12. Press in headrest guides -3- -Arrows O- until the locking tabs engage audibly. => 745219 Removing and installing padding for rear backrest - section on "Information"
13. Position the support -1- -Arrow P-.
14. Screw in and tighten fastening screws -2-. => Tightening torque: 4.5 Nm (3.5 ftlb.)+/-0.5 Seconds (+/-0.5 ftlb.)
Subsequent work
Subsequent work - Installing padding for 2/3-split folding rear backrest
1. Install armrest with cover (rear): => 745519 Removing and installing armrest with cover (rear) - section on "Installing"
2. Install lock for rear backrest: => Installing lock for 2/3-split folding rear backrest
3. Install backrest: => 724719 Removing and installing rear backrest - section on "Installing"