942319 Removing and installing halogen bulb
WM 942319 Removing and installing halogen bulb
Preliminary work
1. Remove main headlight. -> 941519 Removing and installing main headlight - section on "Removing" 94151900 Removing and installing main headlights
Removing halogen bulb
Removing dipped beam halogen bulb
1. Remove cover.
1.1. Release cover -1- at the two clips -arrows A-.
1.2. Swivel the cover -1- out of the guides on the main headlight and remove it -arrows B-.
Removing cover
2. Turn bulb holder for dipped beam headlight -1- anti-clockwise -arrow A- and take it out of the main headlight -arrow B-.
Removing bulb holder for dipped beam headlight
3. Pull dipped beam bulb -1- out of the bulb holder for the dipped beam headlight -2- ( -arrow- ).
Removing dipped beam bulb
Removing auxiliary high beam halogen bulb
1. Remove cover.
1.1. Release cover -1- at the two clips -arrows A-.
1.2. Swivel the cover -1- out of the guides on the main headlight and remove it -arrows B-.
Removing cover
2. Turn bulb holder for auxiliary high beam headlight -1- anti-clockwise -arrow A- and take it out of the main headlight -arrow B-.
Removing bulb holder for auxiliary high beam headlight
3. Pull auxiliary high beam bulb -1- out of the bulb holder for the auxiliary high beam headlight -2- ( -arrow- ).
Removing auxiliary high beam headlight bulb
Removing cornering light halogen bulb
1. Remove cover.
1.1. Release cover -1- at the two clips -arrows A-.
1.2. Swivel the cover -1- out of the guides on the main headlight and remove it -arrows B-.
Removing cover
2. Release connector -1- ( -arrows A- ) and pull it off the cornering light bulb -2- ( -arrow B- ).
Pulling off connector on cornering light bulb
3. Turn cornering light bulb -1- anti-clockwise -arrow A- and take it out of the main headlight -arrow B-.
Removing cornering light bulb
Installing halogen bulb
Installing dipped beam halogen bulb
CAUTION
Danger of injury. Danger of material damage if bulbs are used or handled incorrectly.
-> When installed, the headlight has a high voltage.
-> Only bulbs specified in the bulb table may be used.
-> Bulbs with a higher wattage may damage the bulb housing.
-> To prevent short circuits, the load in question must be switched off when changing bulbs.
-> New bulbs must be clean and free of grease. Therefore, never touch bulbs with your bare hands. To change the bulbs, use a cloth or soft paper.
-> Observe the safety instructions when replacing a bulb in a Bi-Xenon headlight.
-> In certain states, it is compulsory to carry spare light bulbs.
Information
- Observe instructions in -> 9423 Bulb table and installation instructions [1][2]Lighting and Horns
1. Insert dipped beam bulb -1- into the bulb holder for the dipped beam headlight -2- ( -arrow- ).
Installing dipped beam bulb
2. Insert bulb holder for dipped beam headlight -1- into the main headlight -arrow A- and turn it clockwise -arrow B-.
Installing bulb holder for dipped beam headlight
3. Fit cover.
3.1. Fit cover -1- down into the guides on the main headlight and swivel it up -arrows A-.
3.2. Press cover -1- onto the main headlight until the two clips engage securely -arrows B-.
Fitting cover
Installing auxiliary high beam halogen bulb
CAUTION
Danger of injury. Danger of material damage if bulbs are used or handled incorrectly.
-> When installed, the headlight has a high voltage.
-> Only bulbs specified in the bulb table may be used.
-> Bulbs with a higher wattage may damage the bulb housing.
-> To prevent short circuits, the load in question must be switched off when changing bulbs.
-> New bulbs must be clean and free of grease. Therefore, never touch bulbs with your bare hands. To change the bulbs, use a cloth or soft paper.
-> Observe the safety instructions when replacing a bulb in a Bi-Xenon headlight.
-> In certain states, it is compulsory to carry spare light bulbs.
Information
- Observe instructions in -> 9423 Bulb table and installation instructions [1][2]Lighting and Horns
1. Insert auxiliary high beam bulb -1- into the bulb holder for the auxiliary high beam headlight -2- ( -arrow- ).
Installing auxiliary high beam headlight bulb
2. Insert bulb holder for auxiliary high beam headlight -1- into the main headlight -arrow A- and turn it clockwise -arrow B-.
Installing bulb holder for auxiliary high beam headlight
3. Fit cover.
3.1. Fit cover -1- down into the guides on the main headlight and swivel it up -arrows A-.
3.2. Press cover -1- onto the main headlight until the two clips engage securely -arrows B-.
Fitting cover
Installing cornering light halogen bulb
CAUTION
Danger of injury. Danger of material damage if bulbs are used or handled incorrectly.
-> When installed, the headlight has a high voltage.
-> Only bulbs specified in the bulb table may be used.
-> Bulbs with a higher wattage may damage the bulb housing.
-> To prevent short circuits, the load in question must be switched off when changing bulbs.
-> New bulbs must be clean and free of grease. Therefore, never touch bulbs with your bare hands. To change the bulbs, use a cloth or soft paper.
-> Observe the safety instructions when replacing a bulb in a Bi-Xenon headlight.
-> In certain states, it is compulsory to carry spare light bulbs.
Information
- Observe instructions in -> 9423 Bulb table and installation instructions [1][2]Lighting and Horns
1. Insert cornering light bulb -1- into the main headlight -arrow A- and turn it clockwise -arrow B-.
Installing cornering light bulb
2. Plug in connector -1- on cornering light bulb -2- ( -arrow- ) until the connector -1- engages securely.
Plugging in connector on cornering light bulb
3. Fit cover.
3.1. Fit cover -1- down into the guides on the main headlight and swivel it up -arrows A-.
3.2. Press cover -1- onto the main headlight until the two clips engage securely -arrows B-.
Fitting cover
Subsequent work
1. Install main headlight and carry out a function test. -> 941519 Removing and installing main headlight - section on "Installing" 94151900 Removing and installing main headlights