942355 Replacing halogen bulb

WM 942355 Replacing halogen bulb

Information





Bulb table





Preliminary work

1. Remove main headlight. -> 941519 Removing and installing main headlight - section on "Removing" 941519 Removing and installing main headlights

Removing halogen bulb

Removing halogen bulb for high beam headlight

NOTICE

Incorrect handling of bulbs

- Risk of damage to bulbs and the bulb housing

-> Switch off ignition and remove ignition key.
-> Switch off the relevant loads when changing bulbs.
-> Only use bulbs listed in the bulb table.
-> Only install clean bulbs that are free of grease.
-> Always use a cloth or soft paper when working with bulbs.
-> Observe the safety instructions when changing a bulb in a Bi-Xenon headlight.
-> In certain states, it is compulsory to carry spare light bulbs.

Information

- The work steps are described for the left rear door of the vehicle and must be performed in the same way on the other doors. Any different work steps are marked/highlighted.

1. Release the side cover at the clip -a- and open it.





Opening cover

2. Loosen the two fastening screws -1- used to secure the halogen bulb.





Loosening fastening screws

3. Remove the halogen bulb and socket from the bracket by turning once in direction of arrow.
4. Unplug connector on halogen bulb.





Removing connector

Removing halogen bulb for static cornering light

NOTICE

Incorrect handling of bulbs

- Risk of damage to bulbs and the bulb housing

-> Switch off ignition and remove ignition key.
-> Switch off the relevant loads when changing bulbs.
-> Only use bulbs listed in the bulb table.
-> Only install clean bulbs that are free of grease.
-> Always use a cloth or soft paper when working with bulbs.
-> Observe the safety instructions when changing a bulb in a Bi-Xenon headlight.
-> In certain states, it is compulsory to carry spare light bulbs.

Information

- The work steps are described for the left rear door of the vehicle and must be performed in the same way on the other doors. Any different work steps are marked/highlighted.

1. Release the side cover at the clip -a- and open it.





Opening cover

2. Remove the halogen bulb and socket from the bracket by turning once in direction of arrow.





Removing halogen bulb

3. Unplug connector on halogen bulb.





Removing connector

Installing halogen bulb

Installing halogen bulb for high beam headlight

NOTICE

Incorrect handling of bulbs

- Risk of damage to bulbs and the bulb housing

-> Switch off ignition and remove ignition key.
-> Switch off the relevant loads when changing bulbs.
-> Only use bulbs listed in the bulb table.
-> Only install clean bulbs that are free of grease.
-> Always use a cloth or soft paper when working with bulbs.
-> Observe the safety instructions when changing a bulb in a Bi-Xenon headlight.
-> In certain states, it is compulsory to carry spare light bulbs.

Information

- The work steps are described for the left rear door of the vehicle and must be performed in the same way on the other doors. Any different work steps are marked/highlighted.

1. Plug in connector on halogen bulb.





Inserting connector

2. Insert the halogen bulb into the bracket and position it under the two fastening screws by turning once in direction of arrow.





Fitting halogen bulb

3. Tighten the two fastening screws -1-.
4. Close the side cover until it engages securely.

Installing halogen bulb for static cornering light

NOTICE

Incorrect handling of bulbs

- Risk of damage to bulbs and the bulb housing

-> Switch off ignition and remove ignition key.
-> Switch off the relevant loads when changing bulbs.
-> Only use bulbs listed in the bulb table.
-> Only install clean bulbs that are free of grease.
-> Always use a cloth or soft paper when working with bulbs.
-> Observe the safety instructions when changing a bulb in a Bi-Xenon headlight.
-> In certain states, it is compulsory to carry spare light bulbs.

Information

- The work steps are described for the left rear door of the vehicle and must be performed in the same way on the other doors. Any different work steps are marked/highlighted.

1. Plug in connector on halogen bulb.





Inserting connector

2. Insert halogen bulb and lock it by turning once in direction of arrow.





Locking halogen bulb

3. Close the side cover until it engages securely.

Subsequent work

1. Install main headlight. -> 941519 Removing and installing main headlight - section on "Installing" 941519 Removing and installing main headlights