Cassette Player and In-Dash CD Player
AM/FM Stereo Radio With Cassette Player And In-Dash CD Player - Part 1:
AM/FM Stereo Radio With Cassette Player And In-Dash CD Player - Part 2:
FEATURES AND BENEFITS
^ 6 AM/12 FM Radio Station Presets: programmable by following two steps:
1. Tune in desired station on the desired band.
2. Push and hold the desired preset button for approximately one second (until an audio confirmation beep is heard).
^ A. SET (Automatic Station Set): Samples and picks out the strongest radio stations on the band, starting from the lowest station frequency.
^ Electronic Tuning: Automatically locks in station signals for best possible reception.
^ Seek Tuning: Provides up and down seek capability for radio hands to search for the next receivable station.
^ Scan Tuning: Samples program selection for five seconds and then automatically moves to the next radio station. An audible tone indicates scan mode searching after button is held for more than 3 seconds.
^ Automatic Loudness Compensation: Full depth of sound can be heard at low volume levels.
^ Auto Tone Control (ATC):
Allows the sound to be tailored to meet individual preferences. An autotone setting can be set for each radio station preset, the cassette tape player and the CD player. Seven different selectable preset tones are available along with the CSTM (custom) tone. The CSTM tone is set by pressing and rotating the BASS/TREB/FADE/BAL knob.
The setting can be permanently or temporarily shown on the display by pressing and holding the BASS/TREB/FADE/BAL knob until an audible tone is heard.
^ Rotary Bass, Treble, Fade, and Balance Control Knob: The BASS/TREB/FADE/BAL knob allows the bass, treble, fade, and balance modes to be adjusted. Push the knob in until the desired mode is on the display, then rotate to adjust.
^ The Time of Day (Clock) will be displayed when:
1. The ignition is turned Off and the radio power is either On or Off. (Press RCL button if back lighting is desired.)
2. The ignition is turned On and the radio power is Off.
3. The ignition is turned On, the radio is On, and the tune, seek, scan, or preset function has not been activated for ten seconds.
^ Setting the Time of Day (Clock):
1. Push and hold the RCL (Recall) button.
2. While holding the RCL button, push the left side of the auto tone button until the correct hour appears.
3. While holding the RCL button, push the right side of the auto tone button until the correct minute appears.
4. Release the RCL button when complete.
^ Dimming:
All radios feature continuously dimmable nighttime incandescent back lighting for the graphics on the pushbuttons and trimplate. The incandescent back lighting voltage is supplied from the vehicle light switch and is grounded through the radio wiring harness and the radio ground strap. The internal lamps are controlled by the high side pulse width modulated (PWM) dimmer control circuit through the BCM.
The LCD is backlit whenever ignition voltage is applied regardless if the radio power knob is on or off. When the vehicle's exterior lights are turned On, the interior lights knob, which is found to the left of the steering wheel, can be turned to adjust the illumination of the radio. Turning the knob clockwise makes the light get brighter, while turning the knob counter-clockwise results in the light being dimmer.
^ Theft Deterrent: Refer to "Theft Deterrent Feature".
^ OnStar Compatible: Audio inputs, and mute control allow the radio speakers to be used for OnStar communication.
^ On-Board Diagnostics: On-board diagnostics (OBD) are available to check:
^ If any diagnostic trouble codes (DTCs) have been set and the ability to clear the DTCs.
^ If speakers are functioning correctly at two different tones.
^ If all segments on the LCD light up.
^ If all buttons are working.
^ What equalization mode the radio is set at.
^ What antenna signal strength is being read by the radio.