Installation

INSTRUMENT PANEL: LOWER INSTRUMENT PANEL: INSTALLATION

INSTALLATION

1. INSTALL NO. 2 INSTRUMENT PANEL BOX
(a) Install the instrument panel box with the 8 [A] screws.

2. INSTALL GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY
(a) Engage the claw and install the glove compartment door stopper.

3. INSTALL FRONT PASSENGER SEAT BELT WARNING LIGHT
(a) Engage the 2 claws and install the front passenger seat belt warning light.
4. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

(a) Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).
(b) Install the lower instrument panel with the [A] screw, 10 [C] screws, 2 [E] bolts, [F] screw.

(e) Engage the 2 claws and install the DLC3 connector.

5. INSTALL ANTENNA CORD SUB-ASSEMBLY
(a) Connect the 2 clamps and install the antenna cord.

6. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
(a) Engage the 3 claws to connect the hood lock control lever.

7. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL SEAL
(a) Engage the 4 claws and install the instrument finish panel seal.

8. INSTALL RADIO BRACKET
(a) Install the No. 1 radio bracket with the 2 [G] bolts.
Torque: 23 Nm (229 kgf-cm, 17 ft-lbf)
(b) Install the No. 2 radio bracket with the 2 [G] bolts.
Torque: 23 Nm (229 kgf-cm, 17 ft-lbf)

9. INSTALL INSTRUMENT PANEL SUB REINFORCEMENT
(a) Install the instrument panel sub reinforcement with the 2 [D] bolts.

10. INSTALL INSTRUMENT PANEL FINISH LOWER PANEL SUB-ASSEMBLY
(a) Connect the each connectors.
(b) Engage the 2 clips, 7 claws and install the instrument panel finish lower panel.

11. INSTALL NO. 1 SWITCH HOLE BASE
(a) Connect the 2 connectors.
(b) Engage the 2 clips, 3 claws and install the switch hole base.
12. CONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY Installation

13. CONNECT NO. 2 HEATER CONTROL CABLE SUB-ASSEMBLY Installation

14. INSTALL AIR CONDITIONING PANEL ASSEMBLY Installation

15. INSTALL SHIFT LEVER ASSEMBLY (for Automatic Transaxle)

16. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle)

17. INSPECT SHIFT LEVER POSITION (for Automatic Transaxle)

18. ADJUST SHIFT LEVER POSITION (for Automatic Transaxle)

19. INSTALL SHIFT LEVER ASSEMBLY (for Manual Transaxle)

20. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)

21. ADJUST TRANSMISSION CONTROL SELECT CABLE (for Manual Transaxle)

22. INSTALL INSTRUMENT PANEL FINISH LOWER PANEL (for Automatic Transaxle)

(a) Engage the 6 clips and install the instrument panel finish lower panel.

(b) Install the 4 [A] screws.
23. INSTALL INSTRUMENT PANEL FINISH LOWER PANEL (for Manual Transaxle)

(a) Engage the 6 clips and install the instrument panel finish lower panel.

(b) Install the 2 [A] screws.

24. INSTALL FRONT NO. 1 CONSOLE BOX INSERT
(a) Engage the 3 claws and guide and install the front console box insert.

25. INSTALL FRONT NO. 2 CONSOLE BOX INSERT
(a) Engage the 3 claws and guide and install the front console box insert.

26. INSTALL INSTRUMENT CLUSTER FINISH CENTER LOWER PANEL
(a) Connect the connector.
(b) Engage the 2 clips, 4 claws and install the instrument cluster finish center lower panel.

27. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)
(a) Turn the shift lever knob clockwise and install the shift lever knob.
28. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY Installation

29. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY Installation

30. INSTALL COMBINATION METER ASSEMBLY Installation

31. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY Installation

32. INSTALL INSTRUMENT CLUSTER FINISH LOWER PANEL Installation

33. INSTALL INSTRUMENT CLUSTER FINISH CENTER PANEL SUB-ASSEMBLY Installation

34. INSTALL FRONT PILLAR GARNISH RH Installation

35. INSTALL FRONT PILLAR GARNISH LH Installation

36. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH Installation

37. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH Installation

38. INSTALL COWL SIDE TRIM BOARD RH Installation

39. INSTALL COWL SIDE TRIM BOARD LH Installation

40. INSTALL FRONT DOOR SCUFF PLATE RH Installation

41. INSTALL FRONT DOOR SCUFF PLATE LH Installation

42. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Torque: 5.4 Nm (55 kgf-cm, 48 in-lbf)
43. INSPECT SRS WARNING LIGHT
Diagnosis System