Engine Controls - Techstream(R) ECU Re-Flash Procedure
S-SB-0003-10February 4, 2010
Techstream ECU Flash Reprogramming Procedure
Service Category
Engine/Hybrid System
Section
Engine Control
Market
USA
Applicability
TSB SUPERSESSION NOTICE
The information contained in this TSB supersedes TSB No. SS003-07.
^ Applicability has been updated to include 2009 - 2011 model year Scion vehicles.
^ A new section, Techstream Preparation, has been added.
^ Techstream Lite has been added as an option in Required Tools & Materials.
^ Process Overview and Operation Procedure sections have been updated.
TSB No. SS003-07 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding.
Introduction
Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual service bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TI S) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information.
ECU
Electronic Control Unit (ECU) is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term "ECU" is used as a generic label for the following SAE J1930 standard references:
^ Powertrain Control Module (PCM)
^ Engine Control Module (ECM)
^ Transmission Control Module (TCM)
^ Or any other Toyota specific control unit
Warranty Information
Parts Information
NOTE
Authorized Modification Labels may be ordered in packages of 25 from the Materials Distribution Center (MDC) through Dealer Daily - Dealer Support Materials Orders.
Required Tools & Equipment
Process Overview
Techstream ECU flash reprogramming is a 4-step process:
1. Verify the vehicle's applicability for recalibration and locate desired calibration file by performing the Techstream Health Check function.
NOTE
Techstream will automatically search TIS for the appropriate service bulletin using the current Calibration ID from the vehicle. Calibration file links can be found embedded in the corresponding service bulletin.
2. Connect the GR8 Battery Diagnostic Station using "Power Supply Mode" only.
The GR8 Battery Diagnostic Station includes a Power Supply Mode to help maintain battery voltage at 13.5 volts during ECU reprogramming.
NOTICE
ECU damage may occur if the correct battery charger mode setting is NOT used.
3. Locate appropriate calibration ID and reprogram the vehicle ECU with Techstream.
Techstream uses the Calibration Update Wizard (CUW) application to open calibration files and facilitate the ECU flash reprogramming process.
4. Attach the Authorized Vehicle Modification Label.
Modifications to ECU calibrations MUST be recorded and properly displayed on the vehicle using the Authorized Modification Label.
Techstream Preparation
Selecting the TIS Techstream VIM or the Mongoose MFC VIM.
Techstream software requires a VIM selection before you can use the Mongoose MFC VIM. If using TIS Techstream no changes are needed.
Perform the following:
1. Select Setup from the Techstream Main Menu screen.
2. Select VIM Select from the Setup drop down menu.
3. Select the correct Interface Setup from the drop down list. If using Techstream Lite select Mongoose MFC.
NOTE
Mongoose MFC Software and Driver MUST be installed before Mongoose MFC selection will be available.
See TIS - Diagnostics - Scantool page for additional information.
^ If using TIS Techstream select TIS Techstream VIM (this is the default).
4. Click OK.
Operation Procedure
1. Verify the vehicle's applicability for recalibration and locate desired calibration file.
A. Connect Techstream and establish a vehicle connection.
B. Click the Health Check button on the System Select tab.
C. Choose desired ECU group(s) in the Health Check dialog box.
D. Click Next.
E. Click Continue to view Health Check results.
F. Available calibration updates are indicated by a link in the Cal. Update? column. Click the link to access the appropriate service bulletin on TIS.
NOTE
^ Note any DTCs stored in Systems that will be flash reprogrammed.
^ Clicking the Yes link will automatically launch TIS and perform a calibration search.
H. To review the TSB and access the calibration file click the service bulletin link in the Document Title column of the Calibration Search Result portlet.
NOTE
Only Toyota Certified Technicians and above may access calibration files.
2. Connect the GR8 Battery Diagnostic Station.
A. Connect the GR8 Battery Diagnostic Station to the vehicle and turn it ON.
B. Select Power Supply Mode by following the screen flow.
NOTICE
^ ECU damage may occur if the correct battery charger and mode setting are NOT used.
^ Power Supply Mode is used to maintain battery voltage at 13.5 volts while flash reprogramming the vehicle.
^ For details on how to use the GR8 Battery Diagnostic Station, refer to the GR8 Instruction Manual located on TIS, Diagnostics - Tools & Equipment - Battery Diagnostics.
3. Click the appropriate calibration ID and reprogram the vehicle's ECU with Techstream.
A. After reviewing the procedures outlined in the selected TSB, click the appropriate calibration ID link by matching the vehicle's current calibration ID to the Previous Calibration ID in the Calibration Identification Chart.
NOTE
^ Calibration files are embedded as live links in the service bulletin.
^ Some vehicles require special preparation - please review the selected TSB carefully.
B. Click Open to load calibration file information.
NOTE
Techstream pulls calibration files as needed to ensure the latest calibration file is used. Do NOT save calibrations locally on the hard drive or other media.
NOTICE
Errors during the flash reprogramming process can permanently damage the vehicle ECU. Minimize the risk by following the steps below.
^ Battery voltage MUST NOT FALL BELOW 11.4 volts during reprogramming. Confirm battery voltage is higher than 11.4 volts, but be sure voltage DOES NOT RISE ABOVE 16.0 volts during reprogramming.
^ Turn OFF all vehicle accessories (e.g. audio system, A/C, interior lights, DRL, etc.). Do NOT add to or significantly change the vehicle's electrical load while reprogramming.
^ Confirm the hood is open and ensure under hood temperature does NOT exceed 158°F (70°C).
^ Confirm cable connections between the vehicle and Techstream are secure.
^ Do NOT disconnect or turn off Techstream or vehicle ignition during reprogramming.
^ Set parking brake.
^ Complete ALL flash calibration updates provided for each ECU.
^ If the battery's state of charge or capacity are in question, test with SST. No. 00002-V8150-KIT "Digital Battery Analyze,;" and follow TSB No. PG001-06, "Battery Maintenance for In-Stock Vehicles & Pre-Delivery".
^ The GR8 Battery Diagnostic Station MUST be used in Power Supply Mode to maintain battery voltage at 13.5 volts while flash reprogramming the vehicle. For details on how to use the GR8 Battery Diagnostic Station, refer to the GR8 Instruction Manual located on TIS, Diagnostics - Tools & Equipment - Battery Diagnostics.
C. Click Next to start the calibration update process.
D. When using TIS Techstream select Techstream VIM as the desired programming device. Then click Next.
When using Techstream Lite select Generic J2534 Interface. Then click Next.
E. Confirm the following:
^ PC is connected to VIM.
^ VIM is connected to DLC3 connector.
^ Ignition is ON and engine is OFF.
Then click Next.
F. Verify correct current calibration and new calibration information. Then click Next.
NOTE
^ The total number of calibration IDs in the calibration file corresponds to the number of reprogrammable processors in the ECU.
^ Each calibration file may contain up to three separate calibrations.
^ Figure 17 shows an example of the update procedure for a two-processor ECU.
G. Turn ignition OFF. Then click Next.
H. Confirm the following:
^ Ignition is ON and engine is OFF.
^ Hood is open.
^ All accessories are OFF.
^ Battery voltage is above 11.4 volts.
NOTICE
Verify the vehicle is connected to a battery charger before continuing - If battery voltage falls below 11.4 volts, ECU damage may occur.
Then click Start.
I. Do NOT disturb the vehicle during flash reprogramming.
NOTE
^ ECU flash reprogramming may take anywhere from 3 - 30 minutes per calibration file.
^ Reprogramming time will vary depending on model and ECU communication protocol. Vehicles using CAN communication protocol will reprogram much faster (2 - 7 minutes).
NOTE
^ If vehicle requires only ONE calibration update, then proceed to step N in this bulletin.
^ If vehicle requires a SECOND calibration update, then continue as follows:
^ For serial communication vehicles, go to step J.
^ For CAN communication vehicles, go to step L.
J. When Cal 1 has completed the update process turn ignition OFF for a minimum of 10 seconds. Then click Next.
K. Turn ignition to the ON position. Then click Start.
NOTE
If key cycle is NOT done properly, reprogramming will stop at 10% and Cal 2 will fail to load.
L. Do NOT disturb the vehicle during flash reprogramming.
M. Turn ignition OFF for a minimum of 10 seconds. Then click Next.
N. Turn ignition to the ON position. Then click Next.
0. Confirm all calibrations were updated as specified in the service bulletin. Then click Finish.
On some models, DTCs may set as a result of reprogramming. If DTCs are present, clear codes and run the Health Check again. Troubleshoot any remaining Current, Pending, or History codes. Permanent codes will not be cleared using Techstream. Permanent codes do not illuminate the MIL and do not require troubleshooting. They will clear during normal driving once the Universal Trip Drive Pattern is performed.
4. Attach the Authorized Modifications Label.
A. Using a permanent marker or ball point pen complete the Authorized Modifications Label and attach to the vehicle. The Authorized Modifications Label is available through the MDC P/N 00451-00001-LBL.
B. Attach the label under the hood in the location determined by the specific TSB or Campaign.
NOTE
Wait 60 - 90 seconds for ink to set before handling.