General Precautions
BLOCK DRIVE WHEELSBlock the drive wheels as a safety precaution, before beginning any service with the vehicle on the ground.
SUPPORT THE VEHICLE
Never work under a vehicle supported only by a jack. Use jackstands, on a flat and level hard surface, for safe support.
EYE PROTECTION
Always wear appropriate eye protection.
CATALYTIC CONVERTERS
Use caution when working near the catalytic converter to prevent the possibility of burns. The temperatures within the converter can exceed 650° C (1200° F).
BEFORE STARTING SERVICE
1. Be sure to perform the jobs listed in the Maintenance Schedules.
2. When a Vehicle is brought in for maintenance, carefully listen to the owner's explanations of the symptoms exhibited by the Vehicle. Also ask the owner if there are any modifications on the Vehicle. List the problems in your notebook, and refer to them when trying to diagnose the trouble.
3. All jewelry should be removed. Suitable work clothes should be worn.
4. Be sure to wear goggles.
5. Use fender, floor and seat covers to prevent the Vehicle from being scratched or damaged.
6. Never smoke while working.
7. Before removing underfloor bolts (including the rear Differential filler plug) coated with bituminous wax, remove old wax. Re-coat with new wax after reinstallation.
WHILE WORKING
1. When jacking up the Vehicle, be sure to use safety stands.
2. When jacking up the front or rear end of the car body, be sure to chock the tires remaining in contact with the ground.
3. Keep the parking Brake applied when working on the Vehicle. Chock the tires remaining in contact with the ground (and set the selector lever to "P" position in Automatic Transmission (AT) Vehicle), when the Parking Brake cannot be applied, such as when the Brakes are being worked on.
4. Keep the Ignition key turned "OFF" if at all possible.
5. Be cautious while working when the Ignition key is "ON"; if the Engine is hot, the Cooling Fan may start to operate.
6. While the Engine is in operation, properly ventilate the workshop.
7. While the Engine is in operation, be aware of any moving parts, such as the Cooling Fan and the Drive Belt.
8. Keep your hands off any metal parts such as the Radiator, Exhaust Manifold, Exhaust Pipe, and Muffler to prevent burning yourself.
9. When servicing the Electrical System or the Fuel System, disconnect the Ground Cable from the Battery.
10. When disassembling, arrange the parts in the order that they were disassembled.
11. When removing a Wiring Connector, do not pull the wire but pull the Connector itself.
12. When removing a hose or tube, remove the clip first. Then, pull the hose or tube while holding its end fitting.
13. Replace gaskets, 0-rings, snap rings, lock washers, etc.. with new ones.
14. When tightening a bolt or nut, tighten it to the specified torque.
15. When performing work requiring special tools, be sure to use the designated ones.
16. After completing work, make certain that the hoses, tubes and wiring harnesses are securely connected.
17. After completing work, be sure to wash the Vehicle.
TREATMENT FOR USED ENGINE OIL
ENGINE OILS
Prolonged and repeated contact with mineral oil will result in the removal of natural fats from the skin, leading to dryness, irritation and dermatitis. In addition, used Engine oil contains potentially harmful contaminants which may cause skin cancer. Adequate means of skin protection and washing facilities should be provided.
HEALTH PROTECTION PRECAUTIONS
1. Avoid prolonged and repeated contact with oils, particularly used Engine oils.
2. Wear protective clothing, including impervious gloves where practicable.
3. Do not put oily rags in pockets.
4. Avoid contaminating clothes, particularly underpants, with oil.
5. Overalls must be cleaned regularly. Discard non-washable clothing and oil impregnated footwear.
6. First aid treatment should be obtained immediately for open cuts and wounds.
7. Use barrier creams, applying them before each work period, to help the removal of oil from the skin.
8. Wash with soap and water to ensure all oil is removed (skin cleansers and nail brushes will help). Preparations containing lanolin replace the natural skin oils which have been removed.
9. Do not use petroleum, kerosene, diesel fuel, gas oil, thinners or solvents for washing skin.
10. If skin disorders develop, obtain medical advice.
11. Where practicable, degrease components prior to handling.
12. Where there is a risk of eye contact, eye protection should be worn, for example, chemical goggles or face shields; in addition, an eye wash facility should be provided.
ENVIRONMENTAL PROTECTION PRECAUTIONS
- It is illegal to pour used oil on to the ground, down sewers or drains, or into water courses. The burning of used Engine oil in small space heaters or boilers is not recommended unless emission control equipment is fitted. If in doubt, check with the Local Authority.
- Dispose of used oil through authorized waste disposal contractors, licensed waste disposal sites, or to the waste oil reclamation trade. If in doubt, contact the Local Authority for advice on disposal facilities.
HANDLING AN AUTOMATIC TRANSMISSION (AT) VEHICLE
1. The Engine can not be started by pushing the Vehicle, and also the Vehicle can not be moved by operating the Starter Motor.
2. Be sure to release the Accelerator Pedal before shifting from the "R" to the "N" range and from the "N" to the "D" range, or vise versa even when the Vehicle is stopped.
3. Do not maintain the Vehicle in a stall operation for more than five seconds as this may overheat the Clutch excessively.
4. When the Speedometer malfunctions, a Vehicle speed signal will no longer be emitted. Immediately have it repaired.
5. Use only genuine Subaru Automatic Transmission (AT) fluid in the Transmission.
FULL-TIME AWD MANUAL TRANSMISSION (MT) MODELS
SPEEDOMETER TEST (Jack-up Method)
1. Position Vehicle so that front wheels are placed between rollers of speedometer test machine.
2. Jack up Vehicle until rear wheels clear the floor, and support with safety stands.
3. Start Engine with Shift Lever set in 2nd gear (for safety considerations). Perform Speedometer tests.
WARNING:
- Secure a rope or wire to the front towing hook to prevent the lateral runout of front wheels.
- Do not abruptly depress/release Clutch Pedal or Accelerator Pedal during tests even when Engine is operating at low speeds since this may cause Vehicle to jump off test machine.
- Avoid abrupt braking after tests.
- In order to prevent the Vehicle from slipping due to vibration, do not place any wooden blocks or similar items between the safety stands and the Vehicle.
- Since the rear wheels will also be rotating, do not place anything near them. Also, make sure that nobody goes in front of the Vehicle.
SPEEDOMETER TEST (Free Roller Method)
1. Position Vehicle so that front wheels are placed between rollers of test machine.
2. Scribe alignment mark corresponding with centerline of rear wheels on floor.
3. Back up Vehicle so that centerline of free rollers are aligned with mark scribed in step 2.
4. Drive Vehicle onto free rollers.
5. Perform speedometer tests.
WARNING:
- Secure a rope or wire to the front towing hook to prevent the lateral runout of front wheels
- Do not abruptly depress/release Clutch Pedal or Accelerator Pedal during tests even when Engine is operating at low speeds since this may cause Vehicle to jump off test machine.
- Avoid abrupt braking after tests.
BRAKE TEST
1. Drive Vehicle for a distance of several kilometers (miles) to stabilize dragging force of viscous coupling.
2. Place Vehicle onto Brake tester.
3. Perform Brake tests.
Effect of braking force on viscous coupling torque: Approximately 245 N (25 kg, 55 lb).
NOTE: If dragging force exceeds specifications, check Brake pad or Brake shoe for dragging. Abnormalities related to the viscous torque of viscous coupling unit may cause excessive dragging force. At this point, raise Vehicle so that two front or rear wheels clear floor, remove cause of abnormality and check wheel rotation.
CHASSIS DYNAMOMETER TEST
1. Locate Vehicle onto chassis dynamometer tester.
2. Locate rear wheels onto free rollers.
3. Perform dynamic performance tests.
WARNING:
- Do not abruptly depress/release Clutch Pedal or Accelerator Pedal during tests.
- Avoid abrupt braking after tests.
TIRE BALANCE TEST (On-Car Machine)
1. Raise Vehicle so that left and right wheels to be checked clear the floor. Support wheels using pick-up stands.
2. Raise the other two wheels off the ground and support with a safety stand.
3. Attach on-car machine to wheels to be checked.
4. Drive wheel with Engine and perform tire balance tests.
CAUTION:
- Perform tire balance tests after each tire balance has been measured.
- Locate the Vehicle so that its front and rear sides are equal in height.
- Release parking Brake.
- Manually rotate each tire and check for drag.
- Do not operate Clutch and do not accelerate the Engine abruptly.
- If error occurs due to Engine operation, do not operate balance's motor.
TOWING
1. Loading Vehicle onto dolly or flat-bed truck.
CAUTION:
- Transport Vehicle using a dolly or flat-bed truck whenever possible.
- Move shift lever to "1st" position and apply Parking Brake.
2. Towing with a rope.
CAUTION:
- Use a rope only when power train and all wheels are operating properly.
- The Ignition switch should be in the "ACC" position. Never have the Ignition Switch on "LOCK" while the Vehicle is being towed because steering will not be possible, since the direction of the wheels will be locked.
- Put the Transmission in neutral.
- Never use the tie down hooks for towing.
- Remember that Brake Booster and Power Steering will not work when Engine is "OFF". You will have to use greater effort for the Brake Pedal and Steering Wheel.
- Before towing, check Transmission oil and Differential oil levels and top up to the specified level if necessary.
3. Towing with front or rear wheels raised.
CAUTION:
- Do not tow Vehicle with only front or rear wheels placed on towing dolly or flat-bed truck. This may degrade viscous coupling performance or cause Vehicle to jump off dolly or truck.
- Do not tow Vehicle with rear wheels raised under any circumstances since this will damage bumper.
- Do not tow Vehicle with front wheels raised under any circumstances since this will damage bumper.
FULL TIME AWD AUTOMATIC TRANSMISSION (AT) MODELS
Before checking or servicing cars with the front wheels raised or on rollers (Brake Tester, Chassis Dynamometer, etc.), always set the car in Four Wheel Drive (FWD) Mode. To set the car in the FWD mode, disconnect the All Wheel Drive (AWD) AWD circuit by inserting a fuse in the FWD Connector inside the Engine compartment. Also chock the rear wheels firmly.
CAUTION: Ensure that the FWD pilot light is on. If the car is left in the AWD mode, it will surge abruptly when the wheels turn, possibly damaging the Transfer Clutch.
TOWING
1. Loading Vehicle onto dolly or flat-bed truck.
CAUTION:
- Transport Vehicle using a dolly or flat-bed truck whenever possible.
- Place the Selector Lever in "P" position and apply the Parking Brake.
2. Towing with a rope.
CAUTION:
- Tow Vehicle with a rope only when power train and all wheels are operating properly.
- Put a spare fuse inside the FWD connector and never exceed 30 km/h (19 MPH). Also, do not tow for more than 50 km (31 miles).
- Place the Selector Lever in "N" position.
- The Ignition Switch should be in the "ACC" position while the Vehicle is being towed.
- Never use the tie down tabs for towing.
- Remember that Brake Booster and Power Steering will not work when the Engine is "OFF". You will have to use greater effort for the Brake Pedal and Steering Wheel.
- Before towing, check Transmission oil and Differential oil levels and top up to the specified level if necessary.
3. Towing with front or rear wheels raised.
CAUTION: Do not tow Vehicle with front or rear wheels raised under any circumstances since this will damage bumper.
FRONT WHEEL DRIVE (FWD) MODELS WITH TCS
When a test in which only the front wheels are to be driven is performed (Speedometer test, etc.), be sure to turn off the TCS Switch.