Front Seat (Separate Type: Power Adjuster)
DISASSEMBLYHINT: Tape the screwdriver tip before using it to remove the parts.
1. REMOVE HEADREST
2. REMOVE FRONT SEAT CUSHION SHIELD
a. Remove the screw and front seat cushion shield and disconnect the lumbar support switch connector.
b. Remove the 2 screws and lumbar support switch.
3. REMOVE SLIDE KNOB AND RECLINING KNOB
Using a screwdriver, remove the slide knob and reclining knob.
4. REMOVE SWITCH BASE
Using a screwdriver, remove the switch base.
5. REMOVE FRONT SEAT CUSHION COVER
Using a screwdriver, remove the front seat cushion cover.
6. REMOVE FRONT SEAT CUSHION INNER SHIELD
Remove the 2 screws and front seat cushion inner shield.
7. REMOVE FRONT SEAT INNER BELT
Remove the bolt and front seat inner belt and disconnect the connector.
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
8. REMOVE SEAT CUSHION FRONT SHIELD
Remove the 2 screws and seat cushion front shield.
9. REMOVE SEAT CUSHION LOWER SHIELD
a. Remove the screw.
b. Remove the seat cushion lower shield as shown in the illustration.
c. Employ the same manner described above to the other side.
10. REMOVE POWER SEAT SWITCH
a. Unlatch the front portion of seat cushion cover hook.
b. Turn over the left part of seat cushion cover.
c. Remove the 3 screws.
d. Disconnect the 2 connectors and remove the power seat switch.
11. REMOVE SEAT CUSHION ASSEMBLY
a. Disconnect the connector.
b. Remove the 4 bolts and seat cushion assembly.
Torque: 19 N.m (195 kgf.cm, 14 ft.lbf)
12. REMOVE SEAT CUSHION COVER
a. Unlatch the seat cushion cover hooks, then remove the seat cushion frame from the seat cushion cover with pad.
b. Remove the 12 hog rings and seat cushion cover from the seat cushion pad.
HINT: At the time of reassembly, please refer to the following item. When installing hog rings, take care to prevent wrinkles as much as possible.
13. REMOVE SEATBACK ASSEMBLY
a. Remove the 3 hog rings as shown in the illustration.
HINT: At the time of reassembly, please refer to the following item. When installing hog rings, take care to prevent wrinkles as much as possible.
b. Disconnect the lumbar support connector.
c. Remove the 4 bolts and seatback assembly.
Torque: 43 N.m (440 kgf.cm, 32 ft.lbf)
14. REMOVE ARMREST
a. Open the fastener.
b. Remove the bolt, 3 washer, grommet and armrest.
Torque: 37 N.m (375 kgf.cm, 27 ft.lbf)
c. Remove the armrest cover.
15. REMOVE SEATBACK FRAME
a. Remove the 2 hog rings as shown in the illustration.
b. Turn over the seatback cover upward.
c. Remove the 4 hog rings as shown in the illustration.
HINT: At the time of reassembly, please refer to the following item. When installing hog rings, take care to prevent wrinkles as much as possible.
d. Remove the 2 headrest supports and seatback cover from the seatback pad with the frame.
HINT: At the time of reassembly, do not mistake the direction of the headrest support with the button.
e. Remove the seatback frame from the seatback pad.
16. REMOVE LUMBAR SUPPORT
a. Disconnect the lumbar support connector.
b. Remove the 2 screw and lumbar support.
17. REMOVE SEAT CUSHION INSIDE COVER
a. Remove the 2 screws and seat cushion inside cover.
b. Employ the same manner described above to the other side.
REASSEMBLY
The reassembly procedures are the disassembly procedures in reverse order.