Rear Seat (LH)
DISASSEMBLY1. REMOVE HEADREST
Remove the 2 headrests.
2. REMOVE RECLINING ADJUSTER RELEASE HANDLE
Remove the screw and release handle.
3. REMOVE NO. 1 RECLINING COVER LH
a. Unzip the seat cushion cover.
b. Remove the screw and No. 1 rear seat reclining cover.
4. REMOVE NO. 1 RECLINING COVER RH
a. Unzip the seat cushion cover.
b. Remove the screw and No. 1 rear seat reclining cover.
5. REMOVE SEAT CUSHION UNDER COVER (LH AND RH)
a. Remove the 2 screws and 2 seat cushion under covers.
b. Using a 5 mm hexagon wrench, remove the bolt and cushion.
c. Remove the 10 screws and seat cushion under cover.
6. REMOVE FOLD SEAT LOCK CONTROL CABLE NO. 1
a. Tilt the seat forward.
b. Remove the clamp and fold seat lock control cable as shown in the illustration.
7. REMOVE SEATBACK ASSEMBLY
a. As shown in the illustration, disengage the hook and open the seatback cover.
b. Remove the reclining connecting wire of the LH side edge.
c. Remove the reclining connecting wire of the RH side edge.
d. Remove the 4 bolts and the seatback assembly.
Torque: 41 N.m (420 kgf.cm, 30 ft.lbf)
8. REMOVE ARMREST
9. REMOVE SEATBACK COVER
a. Using a screwdriver, disengage the 4 claws and remove the rear seat shoulder belt cover.
HINT: Tape the screwdriver tip before use.
b. Remove the 4 headrest supports.
c. Disengage the hooks, and remove the seatback frame from the seatback cover with pad.
d. Remove the seatback cover from the seatback pad.
e. Remove the hog rings and seatback cover.
HINT: At the time of reassembly, when instaling hog rings, take care to minimize wrinkles as much as possible.
10. REMOVE REAR SEATBACK BOARD
Using a clip remover, remove the 6 clips and seatback board.
11. REMOVE SEAT ADJUSTER CONTROL CABLE
Remove the 2 clamps and seat adjuster control cable.
12. REMOVE REAR SEAT OUTER BELT
a. Remove the 2 bolts and rear seat shoulder belt guide.
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
b. Remove the nut, rear seat outer belt.
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
13. REMOVE SEAT CUSHION COVER
a. Remove the seat cushion cover with pad from the seat cushion frame.
b. Remove the seat cushion cover from the seat cushion pad.
HINT: At the time of reassembly, when instaling hog rings, take care to minimize wrinkles as much as possible.
14. REMOVE REAR NO. 1 SEAT ADJUSTER
a. Remove the 2 bolts and rear No. 1 seat outer adjuster.
Torque: 43 N.m (440 kgf.cm, 32 ft.lbf)
b. Remove the 2 bolts and rear No. 1 seat inner adjuster.
Torque: 43 N.m (440 kgf.cm, 32 ft.lbf)
c. Remove the 4 screws and 2 hinges covers from the rear No.1 seat outer and inner adjusters.
d. Remove the 2 screws and 2 reclining inner covers from the rear No.1 seat outer and inner adjusters.
15. REMOVE REAR SEAT STAY
Remove the 2 bolts and rear seat stay.
16. REMOVE REAR SEAT CUSHION HINGE (LH AND RH)
a. Using a screwdriver, remove the spring nut and E-rings.
b. Remove the 2 hinge pins, 2 cushion spacers, 2 cushion support springs and 2 rear seat cushion hinges.
17. REMOVE LH REAR SEAT LOCK
Unfasten the bolt, then remove the inner belt and LH rear seat lock.
18. REMOVE RH REAR SEAT LOCK
a. Remove the screw and rear seat lock cover.
b. Remove the bolt, seat belt anchor and inner belt.
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
c. Remove the RH rear seat lock.
REASSEMBLY
The reassembly procedures are the disassembly procedures in reverse order.