Disassembly and Reassembly

REAR NO. 2 SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)

DISASSEMBLY

1. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER RH





a. Disengage the claws and remove the 2 screws and reclining cover LH.
b. Using a screwdriver and remove the screw cover, screw and release handle RH.





c. Disengage the claws and remove the 2 screws and reclining cover RH.





d. Disengage the seatback cover hem.
e. Remove the tether anchor cover.
f. Open the fastener of the seatback cover and remove the rear seat protector.





g. Push the claws and remove the 2 headrest supports.
h. Remove the seatback cover together with the pad.
i. Cut the hog rings and remove the seatback cover.

2. REMOVE REAR SEATBACK COVER RH





a. Insert a screwdriver between the seat cushion cover and seat cushion under cover.

NOTICE: Tape the screwdriver tip before use.

b. Pry the seat cushion cover hem to disengage it.
c. Cut the hog rings and remove the seat cushion cover together with the pad.
d. Cut the hog rings and remove the seat cushion cover.

3. REMOVE REAR SEAT HINGE SUB-ASSEMBLY LH
a. Remove the hinge cover, E-ring, pin, hinge guide and hinge.

4. REMOVE REAR SEAT HINGE SUB-ASSEMBLY RH





a. Using a screwdriver, remove the spring of the seat stay ball-joint.
b. Disconnect the ball-joint from the seat cushion frame.
c. Remove the hinge cover, E-ring, pin, hinge guide, spring and hinge together with the seat stay.

5. REMOVE REAR SEAT CUSHION UNDER COVER RH
a. Remove the 4 screws and cover.

6. REMOVE REAR SEAT INNER BELT ASSEMBLY
a. Remove the nut and belt.

7. REMOVE REAR NO. 1 SEAT LOCK CABLE ASSEMBLY
8. REMOVE FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

REASSEMBLY

1. INSTALL REMOVE SEAT LOCK CONTROL CABLE SUB-ASSEMBLY
2. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY
3. INSTALL REAR SEAT INNER BELT ASSEMBLY
a. Remove the nut and belt.

Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)

4. INSTALL REAR SEAT CUSHION UNDER COVER LH
a. Remove the 4 screws and cover.

5. INSTALL REAR SEAT HINGE SUB-ASSEMBLY RH
a. Install the spring to the ball-joint of the seat stay.
b. Connect the ball-joint to the seat cushion frame securely.
c. Install the spring and hinge guide to the hinge.
d. Install the hinge with the pin and new E-ring.
e. Install the hinge cover.

6. INSTALL REAR SEAT HINGE SUB-ASSEMBLY LH
a. Install the hinge guide to the hinge.
b. Install the hinge with the pin and new E-ring.
c. Install the hinge cover.

7. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER RH
a. Install the seat cushion cover to the seat cushion pad with new hog rings.
b. Install the seat cushion cover together with the pad to the seat cushion frame with new hog rings.





c. Engage the seat cushion cover hem to the seat cushion under cover securely.

8. REMOVE REAR SEATBACK COVER RH
a. Install the seatback cover to the seatback pad with new hog rings.
b. Install the seatback cover together with the pad to the seatback frame.
c. Install the 2 headrest supports.

NOTICE: Be careful not to mistake the headrest support direction.

d. Install the rear seat protector and close the fastener of the seatback cover.
e. Install the tether anchor cover.





f. Engage the seatback cover hem.





g. Install the reclining cover RH with the 2 screws,
h. Install the release handle RH with the screw.
i. Install the screw cover.





j. Install the reclining cover LH with the 2 screws