B1833
SUPPLEMENTAL RESTRAINT SYSTEM: AIRBAG SYSTEM: B1830/57: Short in Driver Side Curtain Shield Squib Circuit
DTC B1830/57 - Short in Driver Side Curtain Shield Squib Circuit
DTC B1831/57 - Open in Driver Side Curtain Shield Squib Circuit
DTC B1832/57 - Short to GND in Driver Side Curtain Shield Squib Circuit
DTC B1833/57 - Short to B+ in Driver Side Curtain Shield Squib Circuit
DESCRIPTION
The driver side curtain shield squib circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly LH.
The circuit signals the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side curtain shield squib circuit.
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
- Perform the simulation method by selecting "check mode" (signal check) with the Techstream Check Mode Procedure.
- After selecting CHECK MODE (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road Diagnosis System.
PROCEDURE
1. CHECK CONNECTOR (NO. 2 FLOOR WIRE - CURTAIN SHIELD AIRBAG ASSEMBLY LH)
(a) Turn the ignition switch off.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Disconnect the connector from the curtain shield airbag assembly LH.
(d) Check the No. 2 floor wire connector and terminals (on the curtain shield airbag assembly LH side) and check that the connector is properly connected to the curtain shield airbag assembly LH.
Result:
C -- CONNECT CONNECTOR PROPERLY
B -- REPLACE NO. 2 FLOOR WIRE
A -- Continue to next step.
2. CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (DRIVER SIDE CURTAIN SHIELD SQUIB)
(a) Disconnect the connector from the curtain shield airbag assembly LH.
(b) Connect the white wire side of SST (resistance 2.1 Ohms) to connector C.
CAUTION: Never connect a tester to the curtain shield airbag assembly LH (driver side curtain shield squib) for measurement, as this may lead to a serious injury due to airbag deployment.
NOTICE:
- Do not forcibly insert the SST into the terminals of the connector when connecting.
- Insert the SST straight into the terminals of the connector.
SST: 09843-18061
(c) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(d) Turn the ignition switch to ON, and wait for at least 60 seconds.
(e) Clear the DTCs stored in the memory DTC Check / Clear.
(f) Turn the ignition switch off.
(g) Turn the ignition switch to ON, and wait for at least 60 seconds.
(h) Check the DTCs DTC Check / Clear.
OK:
DTC B1830/57, B1831/57, B1832/57 and B1833/57 are not output.
HINT: DTCs other than DTC B1830/57, B1831/57, B1832/57 and B1833/57 may be output at this time, but they are not related to this check.
NG -- CHECK CONNECTOR (FLOOR WIRE NO. 2 - CENTER AIRBAG SENSOR ASSEMBLY)
OK -- REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY LH
3. CHECK CONNECTOR (FLOOR WIRE NO. 2 - CENTER AIRBAG SENSOR ASSEMBLY)
(a) Turn the ignition switch off.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Disconnect the SST from connector C.
(d) Check the No. 2 floor wire connector and terminals (on the center airbag sensor assembly side) and check that the connector is properly connected to the center airbag sensor assembly.
Result:
C -- CONNECT CONNECTOR PROPERLY
B -- REPLACE NO. 2 FLOOR WIRE
A -- Continue to next step.
4. CHECK NO. 2 FLOOR WIRE (DRIVER SIDE CURTAIN SHIELD SQUIB CIRCUIT)
(a) Disconnect the connector from the center airbag sensor assembly.
(b) Check for short to B+ in the circuit.
(1) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(2) Turn the ignition switch to ON.
(3) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
(c) Check for open in the circuit.
(1) Turn the ignition switch off.
(2) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(3) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(d) Check for short to ground in the circuit.
(1) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(e) Check for short in the circuit.
(1) Release the activation prevention mechanism built into connector B Diagnosis System.
(2) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(3) Restore the released activation mechanism of connector B to the original condition.
NG -- REPLACE NO. 2 FLOOR WIRE
OK -- Continue to next step.
5. CHECK CENTER AIRBAG SENSOR ASSEMBLY
(a) Connect the connectors to the curtain shield airbag assembly LH and the center airbag sensor assembly.
(b) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(c) Turn the ignition switch to ON, and wait for at least 60 seconds.
(d) Clear the DTCs stored in the memory DTC Check / Clear.
(e) Turn the ignition switch off.
(f) Turn the ignition switch to ON, and wait for at least 60 seconds.
(g) Check the DTCs DTC Check / Clear.
OK:
DTC B1830/57, B1831/57, B1832/57 and B1833/57 are not output.
HINT: DTCs other than DTC B1830/57, B1831/57, B1832/57 and B1833/57 may be output at this time, but they are not related to this check.
NG -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK -- USE SIMULATION METHOD TO CHECK