B1690
SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: B1690/15: Driver Side Door Side Airbag Sensor Malfunction
DTC B1690/15 - Driver Side Door Side Airbag Sensor Malfunction
DTC B1695/16 - Passenger Side Door Side Airbag Sensor Malfunction
DESCRIPTION
The side airbag sensor LH or RH consists of the safing sensor, the diagnostic circuit, the lateral deceleration sensor, etc.
If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.
DTC B1690/15 or B1695/16 is stored when a malfunction is detected in the side airbag sensor LH or RH circuit.
WIRING DIAGRAM
INSPECTION PROCEDURE
PROCEDURE
1. CHECK FOR DTC
(a) Turn the ignition switch to ON, and wait for at least 60 seconds.
(b) Clear the DTCs stored in the memory DTC Check / Clear.
(c) Turn the ignition switch off.
(d) Turn the ignition switch to ON, and wait for at least 60 seconds.
(e) Check for DTCs DTC Check / Clear.
Result
HINT: Codes other than past DTC B1690/15 and B1695/16 may be output at this time, but they are not related to this check.
C -- USE SIMULATION METHOD TO CHECK
B -- CHECK CONNECTION OF CONNECTORS
A -- Continue to next step.
2. CHECK CONNECTION OF CONNECTORS
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(c) Check that the connectors are properly connected to the center airbag sensor and the side airbag sensor RH.
OK:
The connectors are properly connected.
NG -- CONNECT CONNECTORS PROPERLY
OK -- Continue to next step.
3. CHECK CONNECTORS
(a) Disconnect the connectors from the center airbag sensor and side airbag sensor RH.
(b) Check that the connectors (on the center airbag sensor side and the side airbag sensor RH side) are not damaged Electronic Circuit Inspection Procedure.
OK:
The connectors are not deformed or damaged.
NG -- REPLACE HARNESS AND CONNECTOR
OK -- Continue to next step.
4. CHECK SIDE AIRBAG SENSOR RH CIRCUIT
(a) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
(d) Turn the ignition switch off.
(e) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(f) Disconnect the connectors from the center airbag sensor and side airbag sensor RH.
(g) Using a service wire, connect terminals 8 (BBP+) and 11 (BBP-) of connector B.
NOTE: Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(i) Disconnect the service wire from the connector B.
(j) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT DOOR WIRE RH)
OK -- Continue to next step.
5. CHECK SIDE AIRBAG SENSOR RH
(a) Interchange the side airbag sensor LH with RH and connect the connectors to them.
(b) Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.
(c) Turn the ignition switch to ON, and wait for at least 60 seconds.
(d) Clear the DTCs stored in the memory DTC Check / Clear.
(e) Turn the ignition switch off.
(f) Turn the ignition switch to ON, and wait for at least 90 seconds.
(g) Check for DTCs DTC Check / Clear.
Result
(h) Turn the ignition switch off.
(i) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(j) Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.
C -- USE SIMULATION METHOD TO CHECK
B -- REPLACE SIDE AIRBAG SENSOR RH
A -- Continue to next step.
6. CHECK CONNECTION OF CONNECTORS
(a) Check that the connector are properly connected to the rear airbag sensor RH.
OK:
The connectors are properly connected.
NG -- CONNECT CONNECTORS PROPERLY
OK -- Continue to next step.
7. CHECK CONNECTORS
(a) Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.
(b) Check that the connectors (on the rear airbag sensor RH side) is not damaged Electronic Circuit Inspection Procedure.
OK:
The connectors are not deformed or damaged.
NG -- REPLACE HARNESS AND CONNECTOR
OK -- Continue to next step.
8. CHECK REAR AIRBAG SENSOR RH CIRCUIT
(a) Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.
(b) Turn the ignition switch to ON, and wait for at least 60 seconds.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
(d) Turn the ignition switch off.
(e) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(f) Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.
(g) Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector E.
NOTE: Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(i) Disconnect the service wire from the connector E.
(j) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- CHECK FRONT DOOR WIRE RH (SIDE AIRBAG SENSOR RH - NO. 2 FLOOR WIRE)
OK -- Continue to next step.
9. CHECK REAR AIRBAG SENSOR RH
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(c) Disconnect the rear airbag sensor RH connector.
(d) Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.
(e) Turn the ignition switch to ON, and wait for at least 60 seconds.
(f) Clear the DTCs stored in the memory DTC Check / Clear.
(g) Turn the ignition switch off.
(h) Turn the ignition switch to ON, and wait for at least 60 seconds.
(i) Check for DTCs DTC Check / Clear.
OK:
DTC B1695/16 is output.
NG -- REPLACE REAR AIRBAG SENSOR RH
OK -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY
10. CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT DOOR WIRE RH)
(a) Disconnect the No. 2 floor wire connector from the door wire RH.
(b) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(c) Turn the ignition switch to ON.
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
(e) Turn the ignition switch off.
(f) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(g) Using a service wire, connect terminals 8 (BBP+) and 11 (BBP-) of connector B.
NOTE: Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(i) Disconnect the service wire from connector B.
(j) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- REPLACE NO. 2 FLOOR WIRE
OK -- REPLACE FRONT DOOR WIRE RH
11. CHECK FRONT DOOR WIRE RH (SIDE AIRBAG SENSOR RH - NO. 2 FLOOR WIRE)
(a) Disconnect the No. 2 floor wire connector from the door wire RH.
(b) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(c) Turn the ignition switch to ON.
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
(e) Turn the ignition switch off.
(f) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(g) Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.
NOTE: Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(i) Disconnect the service wire from connector C.
(j) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- REPLACE FRONT DOOR WIRE RH
OK -- REPLACE NO. 2 FLOOR WIRE
12. CHECK CONNECTION OF CONNECTORS
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(c) Check that the connectors are properly connected to the center airbag sensor and the side airbag sensor LH.
OK:
The connectors are properly connected.
NG -- CONNECT CONNECTORS PROPERLY
OK -- Continue to next step.
13. CHECK CONNECTORS
(a) Disconnect the connectors from the center airbag sensor and side airbag sensor LH.
(b) Check that the connectors (on the center airbag sensor side and the side airbag sensor LH side) are not damaged Electronic Circuit Inspection Procedure.
OK:
The connectors are not deformed or damaged.
NG -- REPLACE HARNESS AND CONNECTOR
OK -- Continue to next step.
14. CHECK SIDE AIRBAG SENSOR LH CIRCUIT
(a) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
(d) Turn the ignition switch off.
(e) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(f) Disconnect the connectors from the side airbag sensor LH and door side airbag sensor LH.
(g) Using a service wire, connect terminals 8 (BBD+) and 15 (BBD-) of connector B.
NOTE: Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(i) Disconnect the service wire from the connector B.
(j) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT DOOR WIRE LH)
OK -- Continue to next step.
15. CHECK SIDE AIRBAG SENSOR LH
(a) Interchange the side airbag sensor RH with LH and connect the connectors to them.
(b) Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.
(c) Turn the ignition switch to ON, and wait for at least 60 seconds.
(d) Clear the DTCs stored in the memory DTC Check / Clear.
(e) Turn the ignition switch off.
(f) Turn the ignition switch to ON, and wait for at least 60 seconds.
(g) Check for DTCs DTC Check / Clear.
Result
(h) Turn the ignition switch off.
(i) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(j) Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.
C -- USE SIMULATION METHOD TO CHECK
B -- REPLACE SIDE AIRBAG SENSOR LH
A -- Continue to next step.
16. CHECK CONNECTION OF CONNECTORS
(a) Check that the connector are properly connected to the rear airbag sensor LH.
OK:
The connectors are properly connected.
NG -- CONNECT CONNECTORS PROPERLY
OK -- Continue to next step.
17. CHECK CONNECTORS
(a) Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.
(b) Check that the connectors (on the rear airbag sensor LH side) is not damaged Electronic Circuit Inspection Procedure.
OK:
The connectors are not deformed or damaged.
NG -- REPLACE HARNESS AND CONNECTOR
OK -- Continue to next step.
18. CHECK REAR AIRBAG SENSOR LH CIRCUIT
(a) Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.
(b) Turn the ignition switch to ON, and wait for at least 60 seconds.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
(d) Turn the ignition switch off.
(e) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(f) Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.
(g) Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector E.
NOTE: Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(i) Disconnect the service wire from the connector E.
(j) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- CHECK FRONT DOOR WIRE LH (SIDE AIRBAG SENSOR LH - FLOOR WIRE)
OK -- Continue to next step.
19. CHECK REAR AIRBAG SENSOR LH
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(c) Disconnect the rear airbag sensor LH connector.
(d) Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.
(e) Turn the ignition switch to ON, and wait for at least 60 seconds.
(f) Clear the DTCs stored in the memory DTC Check / Clear.
(g) Turn the ignition switch off.
(h) Turn the ignition switch to ON, and wait for at least 60 seconds.
(i) Check for DTCs DTC Check / Clear.
OK:
DTC B1690/15 is output.
NG -- REPLACE REAR AIRBAG SENSOR LH
OK -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY
20. CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT DOOR WIRE LH)
(a) Disconnect the floor wire connector from the door wire LH.
(b) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(c) Turn the ignition switch to ON.
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
(e) Turn the ignition switch off.
(f) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(g) Using a service wire, connect terminals 8 (BBD+) and 15 (BBD-) of connector B.
NOTE: Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(i) Disconnect the service wire from connector B.
(j) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- REPLACE FLOOR WIRE
OK -- REPLACE FRONT DOOR WIRE LH
21. CHECK FRONT DOOR WIRE LH (SIDE AIRBAG SENSOR LH - FLOOR WIRE)
(a) Disconnect the floor wire connector from the door wire LH.
(b) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(c) Turn the ignition switch to ON.
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
(e) Turn the ignition switch off.
(f) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(g) Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.
NOTE: Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(i) Disconnect the service wire from connector C.
(j) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- REPLACE FRONT DOOR WIRE LH
OK -- REPLACE FLOOR WIRE