Part 1

INTERIOR PANELS / TRIM: ROOF HEADLINING: INSTALLATION

INSTALLATION

1. INSTALL ROOF HEADLINING ASSEMBLY (w/o Rear Seat Entertainment System)

(a) Place the roof headlining into the cabin as shown in the illustration.

NOTE: Be careful not to damage the roof headlining when placing it in the cabin.

(b) Install the washer hose.

(d) Install the visor holder with the screw.

HINT: Use the same procedure to install the visor holder on the other side.

(e) Engage the 4 clamps and install the amplifier antenna.
(f) Install the bolt.
Torque: 7.5 Nm (76 kgf-cm, 66 in-lbf)
(g) Connect the connector.

(h) Install the bolt and amplifier antenna.
Torque: 7.5 Nm (76 kgf-cm, 66 in-lbf)
(i) Connect the connector.

(j) Install the washer hose and the amplifier antenna.
(k) Connect the connector.

(l) Engage the 3 clamps and install the roof wire.
(m) Connect the connector.
2. INSTALL ROOF HEADLINING ASSEMBLY (w/ Rear Seat Entertainment System)

(a) Place the roof headlining into the cabin as shown in the illustration.

NOTE: Be careful not to damage the roof headlining when placing it in the cabin.

(b) Install the washer hose.

(d) Install the visor holder with the screw.

HINT: Use the same procedure to install the visor holder on the other side.

(e) Engage the 4 clamps and install the amplifier antenna.
(f) Install the bolt.
Torque: 7.5 Nm (76 kgf-cm, 66 in-lbf)
(g) Connect the connector.

(h) Install the bolt and amplifier antenna.
Torque: 7.5 Nm (76 kgf-cm, 66 in-lbf)
(i) Connect the connector.

(j) Install the washer hose and the amplifier antenna.
(k) Connect the connector.

(l) Engage the 3 clamps and install the roof wire.
(m) Connect the 2 connectors.
3. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

(a) Place the roof headlining into the cabin as shown in the illustration.

NOTE: Be careful not to damage the roof headlining when placing it in the cabin.

(b) Install the washer hose.

(d) Engage the 4 clamps and install the amplifier antenna.
(e) Install the bolt.
Torque: 7.5 Nm (76 kgf-cm, 66 in-lbf)
(f) Connect the connector.

(g) Install the bolt and amplifier antenna.
Torque: 7.5 Nm (76 kgf-cm, 66 in-lbf)
(h) Connect the connector.

(i) Install the washer hose and the amplifier antenna.
(j) Connect the connector.

(k) Engage the 3 clamps and install the roof wire.
(l) Connect the 3 connectors.
4. INSTALL REAR VIEW INNER MIRROR STAY HOLDER COVER (w/ EC Mirror) Installation
5. INSTALL ROOF HEADLINING REAR TRIM COVER LH

(a) Engage the 6 claws and install the roof headlining rear trim cover LH.

6. INSTALL ASSIST GRIP PLUG
(a) Install assist grip plug.

7. INSTALL ASSIST GRIP SUB-ASSEMBLY

HINT: Use the same procedure for the other 4 assist grips.

(a) Install the 2 clips and 2 covers to the assist grip, as shown in the illustration.
(b) Install the assist grip.
8. INSTALL VISOR ASSEMBLY RH (w/ Illumination)

(a) Connect the connector.

(b) Install the 4 screws and the visor.
9. INSTALL VISOR ASSEMBLY LH (w/ Illumination)

HINT: Use the same procedure for both sides.

10. INSTALL VISOR ASSEMBLY RH (w/o Illumination)

(a) Install the 3 screws and the visor.
11. INSTALL VISOR ASSEMBLY LH (w/o Illumination)

HINT: Use the same procedure for both sides.

12. INSTALL VISOR BRACKET COVER RH
(a) Attach the 4 claws to install the visor bracket cover.
13. INSTALL VISOR BRACKET COVER LH

HINT: Use the same procedure for both sides.

14. INSTALL NO. 2 ROOM LIGHT ASSEMBLY
(a) Connect the connector.

(b) Engage the 2 claws and install the No. 2 room light.
(c) Engage the 2 claws and install the lens.
15. INSTALL NO. 1 ROOM LIGHT ASSEMBLY
(a) Connect the connector.

(b) Engage the 4 clips to install the No. 1 room light.
(c) Engage the 4 claws to install the lens.
16. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/ Rear Seat Entertainment System)

(a) Connect the connector.

(b) Engage the 4 clips to install the No. 1 room light.
17. INSTALL ROOF CONSOLE BOX ASSEMBLY
(a) for Short Type:
Install the roof console box Installation.
(b) for Long Type:
Install the roof console box Installation.
18. INSTALL REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY RH

(a) Engage the 5 clips and install the rear window No. 2 side garnish assembly RH.
(b) Install the bolt.
Torque: 6.5 Nm (66 kgf-cm, 58 in-lbf)

(c) Engage the claw and install the cover.
19. INSTALL REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY LH (w/o Power Back Door)

HINT: Use the same procedure for both sides.

20. INSTALL REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY LH (w/ Power Back Door)

(a) Connect the connector.
(b) Engage the 5 clips and install the rear window No. 2 side garnish assembly LH.
(c) Install the bolt.
Torque: 6.5 Nm (66 kgf-cm, 58 in-lbf)

(d) Engage the claw and install the cover.
21. INSTALL REAR WINDOW SIDE GARNISH ASSEMBLY RH

(a) Pass the rear seat outer belt floor anchor through the quarter trim panel.
(b) Engage the 5 clips and install the rear window side garnish.
(c) Install the bolt.
Torque: 6.5 Nm (66 kgf-cm, 58 in-lbf)

(d) Engage the claw and install the cover.
22. INSTALL REAR WINDOW SIDE GARNISH ASSEMBLY LH

HINT: Use the same procedure for both sides.

23. INSTALL QUARTER TRIM PANEL ASSEMBLY RH
(a) Connect the connector.

(b) Engage the 12 clips and install the quarter trim panel assembly.
(c) Install the 2 bolts.
Torque: 6.5 Nm (66 kgf-cm, 58 in-lbf)
(d) Engage the 2 clips.

(e) Engage the 2 claws and install the cover.

(f) Install the outer lap belt anchor with bolt.
Torque: 42 Nm (428 kgf-cm, 31 ft-lbf)

(g) Install the outer lap belt anchor with bolt.
Torque: 42 Nm (428 kgf-cm, 31 ft-lbf)

(h) Engage the 3 claws to install the outer lap belt anchor cover.

Continued in Part 2 Part 2