Component Parts Removal (Part 2)
41. REMOVE FLANGES, PLATES AND DISCS
42. REMOVE TRANSAXLE REAR COVER
a. Remove the thirteen bolts.
b. Tap off the circumference of the cover with a plastic hammer to remove the cover from the transmission case, and remove the cover.
43. REMOVE INTERMEDIATE SHAFT
Remove the intermediate shaft from the transmission case.
44. REMOVE SNAP RING
Using snap ring pliers, remove the snap ring.
45. REMOVE TRANSAXLE HOUSING
Remove the nineteen bolts and transaxle housing.
46. REMOVE DIFFERENTIAL
47. REMOVE GOVERNOR DRIVEN GEAR
a. Remove the governor driven gear.
b. Remove the thrust washer.
48. REMOVE APPLY GASKETS
Remove the two gaskets.
49. REMOVE COUNTER SHAFT LOCK NUTS
a. Using a chisel and hammer, unstake the counter shaft lock nut on both sides.
b. Using SST, remove the lock nut of the driven gear side.
SST 09330 - 00021, 09350 - 32014 (09351 - 32032)
c. Using SST to hold the driven gear, remove the lock nut of the another side.
SST 09330 - 00021 and 09350 - 32014 (09351 - 32032, 09351 - 32170)
50. REMOVE COUNTER DRIVEN GEAR
Using SST, remove the driven gear.
SST 09350 - 32014 (09351 - 32061)
51. REMOVE THRUST NEEDLE BEARING
52. REMOVE COUNTER SHAFT ASSEMBLY
Pull out the counter shaft assembly.
53. REMOVE THRUST BEARING WITH RACE
Remove the thrust bearing with race from the counter shaft assembly.
54. CHECK PISTON STROKE OF UNDERDRIVE CLUTCH
a. Set a dial indicator (long type pick or SST) as shown.
SST 09350 - 32014 (09351 - 32190)
b. Applying and releasing the compressed air (392 - 785 kPa, 4 - 8 kgf/sq.cm, 57 - 114 psi), measure the underdrive clutch piston stroke.
Piston stroke: 1.21 - 1.55 mm (0.0476 - 0.0610 in.)
If the piston stroke is nonstandard, select another flange.
HINT: There are two different flange thickness.
Flange thickness:
2.30 mm (0.0906 in.)
2.50 mm (0.0984 in.)
2.70 mm (0.1063 in.)
55. REMOVE UNDERDRIVE CLUTCH DRUM AND ANTI-RATTLE CLIP
56. CONFIRM THAT UNDERDRIVE BRAKE PISTON MOVES
Using compressed air, confirm that the underdrive brake piston moves smoothly.
57. REMOVE OIL SEAL RINGS
Remove the two oil seal rings.
58. REMOVE FLANGE, PLATES AND DISCS
a. Using SST and press, press in the flange until the snap ring is free from the flange.
SST 09350 - 32014 (09351 - 32070)
b. Using a screwdriver, remove the snap ring.
c. Remove the flange, three plates and discs.
59. REMOVE RETURN SPRING
60. REMOVE UNDERDRIVE BRAKE PISTON
Using low-pressure compressed air (98 kPa, 1 kgf/sq.cm, 14 psi), pop out the brake piston into a rag. Force air into the hole shown and remove the brake piston.
61. REMOVE O-RING FROM PISTON
Remove the two O-rings from the piston.
62. REMOVE SNAP RING
a. Set SST, and tighten the bolt gradually to compress the springs until the snap ring is free from the spring seat.
SST 09350 - 32014 (09351 - 32040)
b. Using snap ring pliers, remove the snap ring.
c. Remove SST.
SST 09350 - 32014 (09351 - 32040)
63. REMOVE RETURN SPRING
Remove the return spring and snap ring.
64. REMOVE PISTON FROM TRANSMISSION CASE WITH COMPRESSED AIR
a. Apply compressed air into the oil passage of the case to remove the piston.
HINT: Hold the piston so it is not slanted and blow with the gun slightly away from the oil hole.
b. If the piston does not pop out with compressed air, use needle-nose pliers to remove it.
65. REMOVE O-RING FROM PISTON
Remove the two O-rings from the piston.
66. REMOVE PARKING LOCK PAWL STOPPER PLATE, TORSION SPRING AND SPRING GUIDE
67. REMOVE PAWL SHAFT CLAMP
Remove the bolt and pawl shaft clamp.
68. REMOVE PARKING LOCK PAWL SHAFT AND LOCK PAWL
69. REMOVE PARKING LOCK SLEEVE
70. REMOVE CAM GUIDE BRACKET
Remove the cam guide bracket as shown.
71. REMOVE MANUAL VALVE SHAFT SPACER
Using a screwdriver and hammer, unstake the spacer and remove it.
72. REMOVE PIN
Using a punch and hammer, drive out the pin.
73. REMOVE MANUAL VALVE SHAFT AND LEVER
a. Remove the retaining spring.
b. Slide out the manual valve shaft and remove the manual valve lever and washer.
74. IF NECESSARY, REPLACE OIL SEAL OF MANUAL SHAFT
a. Using a screwdriver, remove the oil seal.
b. Using a 14 mm socket wrench and hammer, drive in a new oil seal.
c. Apply MP grease to the oil seal lip.
75. REMOVE OIL GALLERY COVER AND GASKET
a. Remove the three bolts.
b. Using a torx wrench, remove the six screws. Remove the gallery cover and gasket.
76. REMOVE B(4) ACCUMULATOR PISTON AND SPRING
77. REMOVE BEARING
Using SST, remove the bearing.
SST 09308 - 00010
78. REMOVE OIL TUBES
a. Remove the four tube clamps from transaxle housing.
b. Using a screwdriver, remove the three oil tubes.
79. REMOVE OIL TUBE APPLY COVER AND GASKET
Remove the three bolts, and remove the cover and gasket.
80. REMOVE BEARING
a. Remove the bolt and retainer.
b. Using SST, remove the bearing.
SST 09308 - 00010