Without Toyota Hand Held Tester
1. INSPECT LINES AND CONNECTORSVisually check for loose connections, sharp bends or damage.
2. INSPECT FUEL TANK FILLER PIPE
Visually check for deformation, cracks or fuel leakage.
3. VISUALLY INSPECT FUEL TANK CAP
Check if the cap and/or gasket are deformed or damaged. If necessary, repair or replace the cap.
4. INSPECT EVAP SYSTEM LINE
a. Warm up the engine and stop the engine. Allow the engine to warm up to normal operating temperature.
b. Install a vacuum gauge (EVAP control system test equipment vacuum gauge) to the EVAP service port on the purge line.
c. If you have no TOYOTA Hand-Held Tester:
Forced driving of the [1][2][3]VSV for the EVAP.
1. Disconnect the [1][2][3]VSV connector for the EVAP.
2. Connect the positive (+) and negative (-) leads from the battery to the [1][2][3]VSV terminals for the EVAP.
3. Start the engine.
d. Check the vacuum at idle.
Vacuum:
Maintain at 0.368-19.713 in.Hg (5-268 in.Aq) for over 5 seconds
HINT: If the vacuum does not change, you can conclude that the hose connecting the [1][2][3]VSV to the service port has come loose or is blocked, or the VSV is malfunctioning.
e. If you have no TOYOTA Hand-Held Tester:
Conclude forced driving of the [1][2][3]VSV for the EVAP.
1. Stop the engine.
2. Disconnect the positive (+) and negative (-) leads from the battery from the [1][2][3]VSV terminals for the EVAP.
3. Connect the [1][2][3]VSV connector for the EVAP.
f. Disconnect the vacuum gauge from the EVAP service port on the purge line.
g. Connect a pressure gauge to the EVAP service port on the purge line.
h. Check the pressure.
1. Close off the air drain hose at the marked position of the canister with a hose clipper or similar instrument.
2. Add the pressure (13.5 - 15.5 in.Aq) from the EVAP service port.
Pressure: 2 minutes after the pressure is added, the gauge should be over 7.7-8.8 in.Aq.
HINT: If you can't add pressure, you can conclude that the hose connecting the [1][2][3]VSV~canister~fuel tank has slipped off or the VSV is open.
3. Check if the pressure decreases when the fuel tank cap is removed while adding pressure.
HINT: If the pressure does not decrease when the filler cap is removed, then you can conclude that the hose connecting the service port to the fuel tank is blocked, etc.
i. Disconnect the pressure gauge from the EVAP service port on the purge line.
5. REMOVE CHARCOAL CANISTER
6. VISUALLY INSPECT CHARCOAL CANISTER
Look for cracks or damage.
7. CHECK FOR CLOGGED FILTER, AND STUCK CHECK VALVE AND DIAPHRAGM
a. Install the plug to port E.
b. While holding port B closed, blow air (1.76 kPa, 18 gf/cm2, 0.26 psi) into port A and check that air flows from port D.
c. While holding port B and port D closed, blow air (1.76 kPa, 18 gf/cm2, 0.26 psi) into port A and check that air does not flow from port C.
d. Apply vacuum (3.43 kPa, 25.7 mmHg, 1.01 in.Hg) to port B, check that the vacuum does not decrease when port C is closed, and check that the vacuum decreases when port C is released.
e. While holding port C closed, apply vacuum (3.43 kPa, 25.7 mmHg, 1.01 in.Hg) to port A and check that air flows into port B.
If a problem is found, replace the charcoal canister.
f. Remove the plug.
8. REMOVE VSV FOR EVAP
9. INSPECT VSV FOR EVAP
10. REINSTALL VSV FOR EVAP
11. REMOVE VSV FOR VAPOR PRESSURE SENSOR
12. INSPECT VSV FOR VAPOR PRESSURE SENSOR
13. REINSTALL VSV FOR VAPOR PRESSURE SENSOR
14. INSPECT VAPOR PRESSURE SENSOR
15. REINSTALL CHARCOAL CANISTER