Canada Model

REMOVAL
1. REMOVE STEERING WHEEL PAD

NOTICE:
^ If the airbag connector is disconnected with the ignition switch at ON or ACC, DTCs will be recorded.
^ Never use airbag parts from another vehicle. When replacing parts, replace with new ones.





a. Place the front wheels facing straight ahead.
b. Using a torx socket wrench, loosen the 2 torx screws until the groove along the screw circumference catches on the screw case.





c. Pull the wheel pad out from the steering wheel and disconnect the airbag connector.

CAUTION: When storing the wheel pad, keep the upper surface of the pad facing upward. Never disassemble the wheel pad.

NOTICE: When removing the wheel pad, take care not to pull the airbag wire harness.





2. REMOVE STEERING WHEEL
a. Disconnect the connector.
b. Remove the steering wheel set nut.
c. Place matchmarks on the steering wheel and main shaft assembly.
d. Using SST, remove the wheel.
SST 09950-50012, (09951-05010, 09952-05010, 09953-05020, 09954-05020)
3. REMOVE LOWER FINISH PANEL
a. Remove the 2 screws and disconnect the hood lock control lever from the panel.
b. Remove the 2 panel set screws.
4. REMOVE UPPER AND LOWER COLUMN COVERS
Remove the 4 screws.
5. REMOVE NO.2 HEATER TO REGISTER DUCT
Remove the clip.
6. REMOVE COMBINATION SWITCH WITH SPIRAL CABLE
a. Disconnect the connectors.
b. Disconnect the airbag connector.
c. Remove the 3 switch set screws.





7. REMOVE SPIRAL CABLE

NOTICE: Do not disassemble the cable or apply oil to it.

8. DISCONNECT NO.2 INTERMEDIATE SHAFT ASSEMBLY
a. Place matchmarks on the shaft assembly and control valve shaft.
b. Loosen the bolt A and remove the bolt B.
9. REMOVE NO.2 INTERMEDIATE SHAFT ASSEMBLY
10. REMOVE STEERING COLUMN PROTECTOR
Remove the bolt.
11. REMOVE STEERING COLUMN ASSEMBLY
a. Disconnect the connectors.
b. Remove the 2 column assembly set bolts and 2 nuts.





12. Tilt Steering Column: REMOVE SLIDING YOKE
a. Remove the bolt.
b. Shift the sliding yoke and place matchmarks on the main shaft and sliding yoke.

INSTALLATION





1. Tilt Steering Column: CONNECT SLIDING YOKE
a. Align the matchmarks on the main shaft and sliding yoke, and connect them.
b. Torque the bolt.
Torque: 35 Nm (360 kgf-cm, 26 ft. lbs.)
2. Non-Tilt Steering Column: INSTALL STEERING COLUMN ASSEMBLY
a. Temporarily tighten the 2 column assembly set bolts and 2 nuts.
b. Connect the connectors.
3. Tilt Steering Column: INSTALL STEERING COLUMN ASSEMBLY
a. Torque the 2 column assembly set bolts and 2 nuts.
Torque: 25 Nm (260 kgf-cm, 19 ft. lbs.)
b. Connect the connectors.
4. INSTALL STEERING COLUMN PROTECTOR
Torque the bolt.
Torque: 5.0 Nm (50 kgf-cm, 44 inch lbs.)





5. Non-Tilt Steering Column: INSTALL NO.2 INTERMEDIATE SHAFT SHAFT ASSEMBLY
a. Connect the No.2 intermediate shaft to the main shaft.
b. Temporarily tighten the bolt A.
6. Tilt Steering Column: INSTALL No.2 INTERMEDIATE SHAFT ASSEMBLY
a. Connect the No.2 intermediate shaft to the sliding yoke.
b. Temporarily tighten the bolt A.
7. CONNECT NO.2 INTERMEDIATE SHAFT ASSEMBLY
a. Align the matchmarks on the No.2 intermediate shaft and control valve shaft, and connect them.
b. Torque the bolt B.
Torque: 35 Nm (360 kgf-cm, 26 ft. lbs.)
c. Torque the bolt A.
Torque: 35 Nm (360 kgf-cm, 26 ft. lbs.)
8. INSTALL SPIRAL CABLE
9. INSTALL COMBINATION SWITCH WITH SPIRAL CABLE
a. Tighten the 3 screws.
b. Connect the connectors.
c. Connect the airbag connector.
10. INSTALL NO.2 HEATER TO REGISTER DUCT
Install the clip.
11. Tilt Steering Column: INSTALL UPPER AND LOWER COLUMN COVERS
Install the 4 screws.
12. INSTALL LOWER FINISH PANEL
a. Tighten the 2 panel set bolts.
b. Connect the hood lock control lever with the 2 screws.





13. CENTER SPIRAL CABLE
a. Check that the front wheels are facing straight ahead.
b. Turn the cable counterclockwise until it locks.
c. Then rotate the cable clockwise about 2.5 turns to left of the center.

HINT: The spiral cable rotates approximately 5 turns maximum.

14. INSTALL STEERING WHEEL
a. Align the matchmarks on the wheel and steering main shaft assembly.
b. Torque the wheel set nut.
Torque: 34 Nm (350 kgf-cm, 25 ft. lbs.)
c. Connect the airbag connector.





15. INSTALL STEERING WHEEL PAD

NOTICE:
^ Make sure that the pad is installed to the specified torque.
^ If the pad has been dropped, or there are cracks, dents or other defects in the case or connector, re place the wheel pad with a new one.
^ When installing the pad, take care that the wiring does not interfere with other parts and is not pinched between other parts.

a. Connect the airbag connector.
b. Install the pad after confirming that the circumference groove of the torx screws are caught on the screw case.
c. Using a torx socket wrench, torque the 2 screws.
Torque: 8.8 Nm (90 kgf-cm, 78 inch lbs.)
16. CHECK STEERING WHEEL CENTER POINT