Canada - Restraints - Airbag Replacement And Disposal
Bulletin
0934
Issue Date
2001-03-07
Reference
BC-01-009
Model
ALL APPLICABLE MODELS
Year Range
2000 ~
Market
Canada
Component
BC
Subject:
SRS AIRBAG COMPONENT REPLACEMENT & DISPOSAL PROCEDURES
The SRS Airbag system is an important safety feature of Toyota vehicles. It supplements the vehicle's seat beat system by providing additional protection to vehicle occupants in the event of a severe frontal or side collision (if equipped with side airbags).
In order to assure correct system operation, it is necessary to replace certain components of the airbag system following a collision. In order to assist technicians in determining which components should be inspected, tested, or replaced, the repair manual information has been organized in the attached matrix and replacement notes.
Even in cases of a minor collision where the SRS does not deploy, the steering wheel pad, front passenger airbag assembly, side airbag assembly, airbag sensor assembly, and side airbag sensor assembly should be inspected and diagnostic and repair procedures.
The attached SRS airbag component replacement information includes the following:
- A matrix indicating components requiring replacement, inspection, or testing after the deployment of the driver and/or passenger SRS airbag.
- Component replacement notes.
- Sample repair manual outlining airbag deployment procedures when scrapping a vehicle. Please refer to the specific vehicle repair manual for procedure to deploy an airbag that has been removed from the vehicle.
CAUTION: SRS Airbag service work can only be performed After 90 seconds from the time the ignition switch is turned to the "lock" position and the negative (-) terminal cable is disconnected from the battery.
2000 TOYOTA SRS PARTS REPLACEMENT REQUIREMENTS* COLLISION REPAIR CHART
* The chart above refer to the Component Replacement Notes.
Note - for all Toyota vehicles
Following all collisions when the SRS does NOT deploy, inspect:
- Steering wheel pad
- Side airbags and seat frames
- Front & side airbag sensors
- Wiring harness and connectors
- Front passenger airbag assembly
- Malfunction indicator lamp for correct operation
Component Replacement Notes
Note 1 - Replace the Steering Wheel Pad:
- If the airbag has been deployed or dropped
- If the steering wheel pad is diagnosed as needing replacement when troubleshooting or during inspection
Note 2 - Inspect and if necessary replace the Spiral Cable:
- If the spiral cable is diagnosed as needing replacement when troubleshooting or during inspection
Note 3 - Inspect and if necessary replace the Steering Wheel:
- If the steering wheel is diagnosed as needing replacement during inspection
Note 4 - Replace the Passenger Airbag assembly:
- If the passenger airbag has been deployed or dropped
- If the airbag is diagnosed as needing replacement when troubleshooting or during inspection
Note 5 - Visually inspect and if necessary replace the following items if deformed:
- Instrument panel and instrument panel reinforcement
- Glove compartment or glove compartment door
Note 6 - Replace the Front Impact Sensors:
- If either the driver or passenger airbag has deployed (replace both front impact sensors)
- If a front sensor is diagnosed as needing replacement when troubleshooting or during inspection
Note 7 - Replace the Airbag Sensor Assembly:
- If any airbag has been deployed in a collision, or the airbag sensor assembly has been dropped, or is diagnosed as needing replacement when troubleshooting
Note 8 - Inspect and if necessary replace the Wire Harness assembly:
- If any part of the SRS wire harness or any connector is diagnosed as needing replacement when troubleshooting or during inspection
Note 9 - Replace the:
- Side Impact Airbag if it has been deployed, dropped, or is diagnosed as needing replacement when troubleshooting or during inspection
- Seat cover if it has cuts and/or frayed seams, or is diagnosed as needing replacement during inspection
- Seat frame if it is bent or has become damaged
Note 10 - Replace the Side Impact Sensors:
- If the side airbag assembly has been deployed, dropped, or is diagnosed as needing replacement when troubleshooting or during inspection
Note 11 - In the event of driver or passenger airbag deployment, replace all seatbelt Pretensioners
DISPOSAL PROCEDURES:
Hint:
When scrapping vehicle equipped with an SRS or disposing of a steering wheel pad (with airbag), always first deploy the airbag in accordance with the procedure described. If any abnormality occurs with the airbag deployment, contact the your zone Parts and Service Consultant. When disposing of a steering wheel pad with an airbag deployed in a collision, follow the same procedure given in step 1-(d) in "DISPOSAL
Caution:
Never dispose of a steering wheel pad which has not had the airbag deployed.
The airbag produces a sizeable exploding sound when it deploys, so perform the operation out of doors and where it will not create a nuisance to nearby residents.
When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise. SST P/N 09082-00700
When deploying an airbag, perform the operation at least 10 m(33 ft.) away from the steering wheel pad. The steering wheel pad is very hot when the airbag is deployed, so leave it alone for at least 30 minutes after deployment.
Use gloves and safety glasses when handling a steering wheel pad with the deployed airbag.
Always wash your hands with water after completing the operation.
Do not apply water, etc. to a steering wheel pad with the deployed airbag.
1. AIRBAG DEPLOYMENT WHEN SCRAPPING VEHICLE
Hint:
Have a battery ready as the power source to deploy the airbag.
a. Check function of the SST.
Caution:
When deploying the airbag, always use the specified SST: SRS Airbag Deployment Tool 09082-00700
1. Connect the SST to the battery.
Connect the red clip of the SST to the battery position (+) terminal and the black clip to the battery negative (-) terminal.
Hint:
Do not connect the yellow connector which will be connected with the supplemental restraint system.
2. Check functioning of the SST.
Press the SST activation switch, and check that the LED of the SST activation switch lights up.
Caution:
If the LED lights up when the activation switch is not being pressed, SST malfunction is probable, so definitely do not use the SST.
b. Install the SST.
Caution:
Check that there is no looseness in the steering wheel and steering wheel pad.
1. Remove the steering column lower cover.
2. Disconnect the airbag connector of the spiral cable.
3. Connect the SST connector to the airbag connector of the spiral cable. SST 09082-00700
4. Move the SST at least 10 m (33 ft) away from the front of the vehicle.
5. Close all doors and windows of the vehicle.
Notice:
Take care not to damage the SST wire harness.
6. Connect the SST red clip to the battery positive (+) terminal and the black clip to the negative (-) terminal.
c. Deploy the airbag.
1. Confirm that no one is inside the vehicle or within 10 m (33 ft) area around the vehicle.
2. Press the SST activation switch and deploy the airbag.
Hint: The airbag deploys simultaneously as the LED of the SST activation switch lights up.
d. Dispose of steering wheel pad (with airbag).
Caution:
The steering wheel pad is very hot when the airbag is deployed, so leave it alone for at least 30 minutes after deployment.
Use gloves and safety glasses when handling a steering wheel pad with the deployed airbag. Always wash your hands with water after completing the operation.
Do not apply water, etc. to a steering wheel pad with the deployed airbag.
1. When scrapping a vehicle, deploy the airbag and scrap the vehicle with the steering wheel pad still installed.
2. When moving a vehicle for scrapping which has a steering wheel pad with deployed airbag, use gloves and safety glasses.
PASSENGER AIRBAG MANUAL ON-OFF SWITCH INSPECTION
1. Inspect Passenger Airbag Manual On-Off Switch Continuity
Hint:
Release the activation prevention mechanism of the passenger airbag manual on-off switch connector on the airbag sensor assembly side.
If continuity is not as specified,replace the switch.
2. Inspection Passenger Airbag Manual On-Off Indicator Operation
a. Check that continuity exists between 5 and 6.
b. Connect the positive (+) lead from the battery to terminal 1 and negative (-) lead to terminal 2.
c. Check that the indicator light lights up.
If the operation is not specified, replace the indicator.
NOTE:
Issue of this Technical Service Bulletin is to ensure that proper repair information is available. IT DOES NOT CONSTITUTE AN AUTHORIZATION FOR REPAIR. Normal provisions of the formal warranty policy, as applicable, will apply.