Rear Seat Belt
REPLACEMENT / Rear Seat BeltRear Seat Belt:
1. REMOVE REAR SEAT ASSY RH
2. REMOVE REAR SEAT ASSY LH
3. REMOVE REAR SEAT HEADREST ASSY RH [71940B / 98-130 ]
4. REMOVE REAR SEAT HEADREST ASSY CENTER [71960B / 98-130 ]
5. REMOVE REAR SEAT BACK BOARD CARPET ASSY RH [71880A /98-130 ]
6. REMOVE SEPARATE TYPE REAR SEAT CUSHION ASSY [71460S ]
7. REMOVE REAR SEAT ARMREST ASSY CENTER [72830 / 98-130 ]
8. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSY RH [72057/98-130 ]
9. REMOVE REAR SEAT SHOULDER BELT COVER [73373 / 98-131 ]
10. REMOVE SEPARATE TYPE REAR SEAT BACK ASSY [71480S ]
11. REMOVE REAR DOOR SCUFF PLATE RH [67917A /98-115 ]
12. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH [62331A / 98-115 ]
13. REMOVE TONNEAU COVER ASSY [64910J /98-117 ]
14. REMOVE DECK BOARD SUB-ASSY [58401 E /98-117 ]
15. REMOVE DECK BOARD SUB-ASSY NO.2 [58408A /98-117 ]
16. REMOVE DECK BOARD SUB-ASSY NO.3 [58409A /98-117 ]
17. REMOVE LUGGAGE COMPARTMENT TRAY [64421A / 9-117 ]
18. REMOVE SPARE WHEEL COVER TRAY [64779 / 9-117 ]
19. REMOVE DECK SIDE TRIM BOX RH [64741 B /98-117 ]
20. REMOVE DECK SIDE TRIM BOX LH [64742C /98-117 ]
21. REMOVE REAR FLOOR FINISH PLATE [58387B / 98-117 ]
22. REMOVE DECK TRIM SIDE PANEL ASSY RH [64730B /98-117 ]
23. REMOVE REAR NO.1 SEAT BELT ASSY OUTER RH [73360C / 98-131]
a. Remove the bolt and the rear seat belt assembly No.1.
24. REMOVE REAR SEAT BELT ASSY OUTER CENTER [733500 / 98-131]
a. Remove the nut and rear seat belt assembly outer center.
25. REMOVE REAR SEAT BELT ASSY INNER [[73380A /98-131]
a. Remove the bolt and rear seat belt assembly inner.
26. INSTALL REAR SEAT BELT ASSY INNER [73380A / 98-131 ]
a. Install the rear seat inner belt with the bolt.
Torque: 42.0 N.m (420 kgf.cm, 31 ft.lbf)
27. INSTALL REAR SEAT BELT ASSY OUTER CENTER [73350C /98-131]
a. Check the ELR lock.
1. With the seat belt installed to the vehicle,check that the belt will lock when the belt is pulled out quickly.
28. INSTALL REAR NO.1 SEAT BELT ASSY OUTER RH [733600 /98-131]
a. Check the degree of tilt when beginning to lock the ELR.
1. Make sure that belt cannot be pulled out by over 45 degrees of tilt.
NOTE: Do not disassemble the retractor.
b. Install the floor anchor with the bolt.
Torque: 42.0 N.m (420 kgf.cm, 31 ft.lbf)
NOTE: Do not make the anchor part run onto the protrusion part of the floor panel.
c. Install the rear No.1 seat belt assembly outer with the bolt.
Torque: 42.0 N.m (420 kgf.cm, 31 ft.lbf)