Removal and Replacement
REMOVAL1. REMOVE REAR SEATS
2. REMOVE REAR FLOOR FINISH PLATE
3. REMOVE REAR DOOR SCUFF PLATES
4. REMOVE ROOM LIGHT AND COVER
a. Using a screwdriver, remove the cover.
HINT: Tape the screwdriver tip before use.
b. Remove the screw and room light, then disconnect the connector.
5. REMOVE ASSIST GRIPS AND COVERS
6. REMOVE FRONT DOOR SCUFF PLATES
7. REMOVE SUN VISORS
Remove the 4 screws and 2 sun visors.
8. REMOVE INNER REAR VIEW MIRROR
9. REMOVE ROOF CONSOLE BOX
a. Using a screwdriver, remove the roof console box cover.
HINT: Tape the screwdriver tip before use.
b. Remove the 3 screws and roof console box, then disconnect the connector.
10. REMOVE DECK SIDE TRIMS
a. Remove the bolt and rear seat outer belt floor anchor.
Torque: 43 N.m (440 kgf.cm, 32 ft.lbf)
b. Remove the 5 screws.
c. Using a screwdriver, remove the deck side trim.
HINT: Tape the screwdriver tip before use.
d. Employ the same manner described above to the other side.
e. LH side:
Disconnect the connector.
11. REMOVE ROOF SIDE INNER GARNISHES
a. Remove the bolt and rear seat outer belt shoulder anchor.
Torque: 43 N.m (440 kgf.cm, 32 ft.lbf)
b. Remove the 3 clips.
c. Using a screwdriver, remove the roof side inner garnish.
HINT: Tape the screwdriver tip before use.
12. REMOVE CENTER PILLAR LOWER GARNISHES
a. Remove the bolt and front seat outer belt floor anchor.
Torque: 43 N.m (440 kgf.cm, 32 ft.lbf)
b. Pull the center pillar lower garnish upward to remove it.
c. Employ the same manner described above to the other side.
13. REMOVE CENTER PILLAR UPPER GARNISHES
a. Remove the bolt and front seat outer belt shoulder anchor.
Torque: 43 N.m (440 kgf.cm, 32 ft.lbf)
b. Using a screwdriver, remove the center pillar upper garnish.
HINT: Tape the screwdriver tip before use.
c. Employ the same manner described above to the other side.
14. REMOVE FRONT PILLAR GARNISHES
a. Using a screwdriver, remove the front pillar garnish.
HINT: Tape the screwdriver tip before use.
b. Employ the same manner described above to the other side.
15. REMOVE ROOF HEADLINING
a. Using a screwdriver, remove the roof headlining trim garnish.
HINT: Tape the screwdriver tip before use.
b. Remove the 2 sun visor holders.
c. Remove the 4 room partition net hooks.
d. Remove the 4 clips and roof headlining.
HINT: At the time of installation, please refer to the following item.
When installing the roof headlining, put the fastener tapes.
16. REMOVE SLIDING ROOF GLASS
a. Using a torx wrench, remove the torx screws.
Torque: 4.0 N.m (40 kgf.cm, 36 in.lbf)
b. Pull the glass upward to remove it.
17. REMOVE SLIDING ROOF DRIVE GEAR
a. Disconnect the 2 connectors.
b. Remove the 3 bolts and drive gear.
Torque: 5.5 N.m (55 kgf.cm, 49 in.lbf)
HINT: At the time of installation, please refer to the following item.
Apply adhesive to 2 gear side bolts.
Part No. 08833-00070, THREE BOND 1324 or equivalent
c. Remove the screw and cam plate cover.
d. Remove the large screw, washers and shims.
e. Turn the drive shaft with a screwdriver to align the housing and gear point mark as shown.
f. Install the cam plate cover with the screw.
18. REMOVE SLIDING ROOF HOUSING
a. Disconnect the 4 drain hoses from the housing.
b. Remove the 6 nuts and 4 bolts, then remove the housing, as shown in the illustration.
Torque: 5.5 N.m (55 kgf.cm, 49 in.lbf)
INSTALLATION
Installation is in the reverse order of removal.