Dashboard / Instrument Panel: Service and Repair
Instrument Panel/Meter - Part 1:
Instrument Panel/Meter - Part 2:
Instrument Panel/Meter - Part 3:
REPLACEMENT
1. TABLE OF BOLT, SCREW AND NUT
HINT: The bolts, the screws and the nuts, which are necessary for installation and removal of the instrument panel, are shown in the illustration with alphabets.
2. DISCONNECT BATTERY NEGATIVE TERMINAL
3. REMOVE STEERING WHEEL COVER LOWER NO.2
4. REMOVE STEERING WHEEL COVER LOWER NO.3
5. REMOVE HORN BUTTON ASSEMBLY
6. REMOVE STEERING WHEEL ASSEMBLY
SST 09950-50013 (09951-05010, 09952-05010, 09953-05020, 09954-05021)
7. REMOVE STEERING COLUMN COVER
8. REMOVE HEADLAMP DIMMER SWITCH ASSEMBLY
9. REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY
10. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
a. Remove the 2 clips.
b. Pull the instrument cluster finish panel sub-assembly rearward to remove it.
11. REMOVE COMBINATION METER ASSEMBLY
a. Remove the 4 screws
b. Pull out the combination meter assembly, then disconnect the connectors.
12. REMOVE FRONT DOOR SCUFF PLATE LH
13. REMOVE FRONT DOOR SCUFF PLATE RH
14. REMOVE COWL SIDE TRIM BOARD LH
15. REMOVE COWL SIDE TRIM BOARD RH
16. REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LOWER LH
a. Remove the 2 bolts .
b. Disconnect the hood lock control cable assembly.
c. Disengage the 2 claws and 3 clips, and then remove the instrument panel finish panel sub-assembly lower LH.
d. Disconnect the connectors.
17. REMOVE INSTRUMENT PANEL SAFETY PAD INSERT SUB-ASSEMBLY NO.1
a. Remove the 4 bolts and instrument panel safety pad insert sub-assembly No.1.
b. Disconnect the connector.
18. REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY
a. Disengage the claw, and remove the glove compartment door stopper sub-assembly.
19. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
a. Push the right side wall and then push the left wall to release the stoppers.
b. Pull the glove compartment door sub-assembly rearward to remove it.
20. REMOVE INSTRUMENT PANEL BOX NO.2
a. Disengage the 2 claws and the 4 clips, and remove the instrument panel box No.2.
21. REMOVE INSTRUMENT SIDE PANEL LH
a. Disengage the 5 claws by pulling up the edge of the instrument side panel LH from the rear of the vehicle.
b. Remove the instrument side panel LH.
22. REMOVE INSTRUMENT SIDE PANEL RH
23. REMOVE INSTRUMENT PANEL REGISTER ASSEMBLY NO.1
a. Disengage the claw and 4 clips, and then remove the instrument panel register assembly No.1.
24. REMOVE INSTRUMENT PANEL REGISTER ASSEMBLY NO.3
25. REMOVE FLOOR CARPET COVER CENTER LH
a. Remove the clip on the floor carpet cover center LH.
b. Depress the edge of the floor carpet cover center LH around the claws to disengage the two claws under beneath of the floor carpet cover center LH.
c. Slightly sliding the floor carpet cover center LH to the front of the vehicle, detach the two claws from the instrument cluster finish panel sub-assembly lower center at the floor carpet cover center LH.
d. Remove the floor carpet cover center LH.
26. REMOVE FLOOR CARPET COVER CENTER RH
27. REMOVE INSTRUMENT CLUSTER FINISH PANEL CENTER NO.1
a. Using a moulding remover, disengage the 3 clips as shown in the illustration.
b. Disconnect the connector and remove the instrument cluster finish panel center No.1.
28. REMOVE INSTRUMENT CLUSTER FINISH PANEL CENTER NO.2
29. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
a. Remove the floor shift shift lever knob sub-assembly.
30. REMOVE FLOOR SHIFT POSITION INDICATOR HOUSING ASSEMBLY
a. Disengage the 4 claws, and remove the floor shift position indicator housing assembly.
31. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY CENTER
a. Remove the screw
b. Disengage the 5 clips and the claw from the lowest part on the instrument cluster finish panel assembly center in order.
c. Disconnect the connectors at the instrument cluster finish panel sub-assembly lower center, and then remove the instrument cluster finish panel assembly center.
32. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY LOWER CENTER
a. Remove the 2 clips on both sides.
b. Remove the 3 screws
c. Pull the instrument cluster finish panel sub-assembly lower center rearward to remove it.
d. Disconnect the connector.
33. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH
a. Insert the edge of a moulding remover between the instrument cluster finish panel garnish and the radio receiver from the top center, and then lean the moulding remover toward the front of the vehicle to raise the instrument cluster finish panel garnish.
b. Disengage the claw on the top of the instrument cluster finish panel garnish and the two clips from the radio receiver.
c. Pull up the instrument cluster finish panel garnish to the front of the vehicle to disengage the 5 claws at the bottom of the instrument cluster finish panel garnish.
d. Remove the instrument cluster finish panel garnish.
34. REMOVE STEREO COMPONENT SPEAKER ASSEMBLY
a. Remove the 2 screws and stereo component speaker assembly.
b. Disconnect the connector.
35. REMOVE RADIO RECEIVER ASSEMBLY W/BRACKET
36. REMOVE INTEGRATION CONTROL & PANEL ASSEMBLY
37. REMOVE FRONT PILLAR GARNISH LH
38. REMOVE FRONT PILLAR GARNISH RH
39. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
a. Using a screwdriver, disengage the 2 clips and remove the instrument panel speaker panel sub-assembly.
40. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY NO.2
41. REMOVE FRONT NO.1 SPEAKER ASSEMBLY
a. Remove the 2 screws and front No.1 speaker assembly. b.Disconnect the connector.
42. REMOVE FRONT NO.2 SPEAKER ASSEMBLY
43. REMOVE DEFROSTER NOZZLE OPENING PLATE NO.1
a. Using a screwdriver, disengage the 6 claws and remove the defroster nozzle opening plate No.1.
b. Disconnect the connector.
44. SEPARATE SHIFT LEVER ASSEMBLY
a. Remove the 4 bolts and separate the shift lever assembly.
45. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY W/PASSENGER AIRBAG ASSEMBLY
a. Remove the 4 bolts and 2 screws
b. Disconnect the connectors.
c. Remove the instrument panel sub-assembly W/ passenger airbag assembly.
46. REMOVE SIDE DEFROSTER NOZZLE DUCT NO.1
a. Remove the 2 screws
47. REMOVE SIDE DEFROSTER NOZZLE DUCT NO.2
a. Remove the 2 screws
48. REMOVE DEFROSTER NOZZLE ASSEMBLY
a. Remove the 4 screws
49. REMOVE HEATER TO REGISTER DUCT NO.1
a. Remove the 3 screws
50. REMOVE HEATER TO REGISTER DUCT NO.2
a. Remove the 3 screws
51. REMOVE HEATER TO REGISTER DUCT NO.3
a. Remove the 2 screws
52. REMOVE SIDE DEFROSTER NOZZLE LH
53. REMOVE SIDE DEFROSTER NOZZLE RH
54. REMOVE INSTRUMENT PANEL FINISH PANEL RETAINER LOWER NO.3
a. Remove the 2 screws
55. REMOVE INSTRUMENT CLUSTER FINISH PANEL REINFORCEMENT
a. Remove the screw
56. REMOVE DEFROSTER DUCT BRACKET NO.1
a. Remove the screw
57. REMOVE INSTRUMENT FINISH PANEL RETAINER LOWER
a. Remove the screw
58. REMOVE INSTRUMENT FINISH PANEL RETAINER LOWER NO.2
a. Remove the screw
59. REMOVE INSTRUMENT PANEL FINISH PANEL RETAINER NO.1
a. Remove the 2 screws
60. REMOVE INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY NO.2
61. REMOVE ANTENNA CORD SUB-ASSEMBLY
62. REMOVE NAVIGATION ANTENNA ASSEMBLY (W/ EMV & NAVIGATION SYSTEM)
63. REMOVE INSTRUMENT PANEL WIRE NO.2
a. Remove the 2 screws
b. Disengage the 7 clamps and remove the instrument panel wire No.2.
64. REMOVE INSTR PNL PASS L/DOOR AIR BAG ASSEMBLY
65. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
66. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY W/PASSENGER AIRBAG ASSEMBLY
a. Using a torque wrench, install the bolt .
Torque: 20 Nm (204 kgf.cm, 14 ft.lbf)
67. INSTALL SHIFT LEVER ASSEMBLY
a. Using a torque wrench, install the 4 bolts.
Torque: 21 Nm (214 kgf.cm, 12.6 ft.lbf)
68. ADJUST SPIRAL CABLE SUB-ASSEMBLY
69. INSTALL STEERING WHEEL ASSEMBLY
70. INSTALL HORN BUTTON ASSEMBLY
71. INSPECT HORN BUTTON ASSEMBLY
72. INSPECT SRS WARNING LIGHT