Rear No. 1 Seat Assembly LH

Rear No. 2 Seat Assembly LH:

OVERHAUL

HINT: The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated.




1. REMOVE REAR SEAT LEG SIDE GARNISH SUB-ASSEMBLY LH
a. Disengage the clips and remove the seat leg side garnish.

2. REMOVE REAR NO.2 SEAT ASSEMBLY LH
a. Remove the bolt and locus cable.
b. Remove the 2 bolts and seat.
c. Remove the 2 headrests.




3. REMOVE RH SEAT REAR SEAT RECLINING COVER
a. Remove the 2 screws.
b. Remove the reclining cover by pulling it out in the arrow mark direction shown in the illustration.




4. REMOVE LH SEAT REAR SEAT RECLINING COVER
a. Remove the 2 screws.
b. Remove the reclining cover by pulling it out in the arrow mark direction shown in the illustration.

5. REMOVE REAR SEATBACK ASSEMBLY LH
a. Disengage the reclining remote control cable.
b. Disengage the rear seat lock release strap cable.
c. Remove the 4 bolts and seatback.

6. REMOVE REAR NO.2 SEAT LAP BELT ASSEMBLY CENTER W/INNER LH
a. Remove the bolt and lap belt.

7. REMOVE RR SEAT COVER BEZEL NO.2
a. Remove the 5 screws and cover bezel.

8. REMOVE NO. 2 SEATBACK LOCK CONTROL BEZEL
a. Remove the screw and lock control bezel.




9. REMOVE NO. 2 SEATBACK COVER LH
a. Disengage the claw and remove the 4 headrest supports.
b. Remove the hog rings and seatback cover together with the pad.
c. Remove the hog rings and seatback cover.




10. REMOVE REAR SEAT LOCK RELEASE STRAP ASSEMBLY
a. Remove the nut and lock release strap.

11. REMOVE REAR SEATBACK CONNECTING LH WIRE
a. Remove the screw and connecting wire.

12. REMOVE RECLINING RELEASE HANDLE SUB-ASSEMBLY LH
a. Remove the nut and reclining release handle.

13. REMOVE RECLINING ADJUSTER RELEASE HANDLE NO.2 LH
a. Remove the nut and reclining adjuster release handle.

14. REMOVE REAR SEAT BELT ASSEMBLY INNER LH
a. Remove the bolt and seat belt.

15. REMOVE REAR NO.2 SEAT BELT ASSEMBLY INNER LH
a. Remove the bolt and seat belt.

16. REMOVE NO.2 SEAT CUSHION COVER SUB-ASSEMBLY LH
a. Remove the hog rings and cushion cover together with the pad.
b. Remove the hog rings and seat cushion cover.

17. REMOVE LOCUS CABLE LH
a. Remove the nut and locus cable.

18. REMOVE NO.2 SEAT CUSHION SPRING ASSEMBLY LH

19. REMOVE REAR SEAT STAY SUB-ASSEMBLY
a. Remove the nut and seat stay.

20. INSTALL REAR SEAT STAY SUB-ASSEMBLY
a. Install the seat stay with the nut.

Torque: 5.5 N.m (56 kgf.cm, 49 in.lbf)

21. INSTALL LOCUS CABLE LH
a. Install the locus cable with the nut.

Torque: 5.5 N.m (56 kgf.cm, 49 in.lbf)




22. INSTALL NO.2 SEAT CUSHION COVER SUB-ASSEMBLY LH
a. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

NOTE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to prevent wrinkles as much as possible.

23. INSTALL REAR NO.2 SEAT BELT ASSEMBLY INNER LH
a. Install the seat belt with the bolt.

Torque: 42 N.m (428 kgf.cm, 31 ft.lbf)

24. INSTALL REAR SEAT BELT ASSEMBLY INNER LH
a. Install the seat belt with the bolt.

Torque: 42 N.m (428 kgf.cm, 31 ft.lbf)

25. INSTALL RECLINING ADJUSTER RELEASE HANDLE NO.2 LH
a. Install the reclining adjuster release handle with the nut.

Torque: 5.5 N.m (56 kgf.cm, 49 in.lbf)

26. INSTALL RECLINING RELEASE HANDLE SUB-ASSEMBLY LH
a. Install the reclining release handle with the nut.

Torque: 5.5 N.m (56 kgf.cm, 49 in.lbf)

27. INSTALL REAR SEAT LOCK RELEASE STRAP ASSEMBLY
a. Install the lock release strap with the nut.

Torque: 5.5 N.m (56 kgf.cm, 49 in.lbf)




28. INSTALL NO. 2 SEATBACK COVER LH
a. Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.

NOTE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to prevent wrinkles as much as possible.

b. Install the 4 headrest supports.

29. INSTALL REAR NO.2 SEAT LAP BELT ASSEMBLY CENTER W/INNER LH
a. Install the lap belt with the bolt.

Torque: 42 N.m (428 kgf.cm, 31 ft.lbf)

30. INSTALL REAR SEATBACK ASSEMBLY LH
a. Install the seatback with the bolt.

Torque: 44 N.m (449 kgf.cm, 32 ft.lbf)

31. INSTALL REAR NO.2 SEAT ASSEMBLY LH
a. Place the seat in the cabin.

NOTE: Be careful not to damage the body.

b. Install the seat with the bolt.

Torque: 29 N.m (296 kgf.cm, 21 ft.lbf)

c. Install the locus cable with the bolt.

Torque: 29 N.m (296 kgf.cm, 21 ft.lbf)

d. Install the 2 headrests.

HINT: Check that the seat leg locks.