Disassembly and Reassembly

Starter Assy:

Starter Assy:

OVERHAUL




1. REMOVE REPAIR SERVICE STARTER KIT
a. Remove the nut and disconnect the lead wire from the repair service starter kit.




b. Remove the 2 screws which are used to secure the repair service starter kit to the repair service starter kit.
c. Remove the repair service starter kit.
d. Remove the return spring and the plunger from the repair service starter kit.




2. REMOVE STARTER YOKE ASSEMBLY
a. Remove the 2 through bolts and pull out the starter yoke together with the starter commutator end frame.




b. Remove the starter yoke from the starter commutator end frame.




3. REMOVE STARTER ARMATURE PLATE
a. Remove the starter armature plate from the starter yoke.




4. REMOVE DRIVE HOUSING STARTER BEARING COVER
a. Using a screwdriver, remove the drive housing starter bearing cover.




5. REMOVE STARTER ARMATURE ASSEMBLY
a. Using snap ring pliers, remove the snap ring and the plate washer.
b. Remove the starter armature from the commutator end frame.




6. REMOVE PLANET GEAR
a. Remove the 3 planet gears from the repair service starter kit.




7. INSPECT REPAIR SERVICE STARTER KIT
a. Check the plunger.
1. Push in the plunger and check that it returns quickly to its original position.
If necessary, replace the repair service starter kit.




b. Check the pull-in coil for open circuit.
1. Using an ohmmeter, check that there is continuity between terminals 50 and C.
If there is no continuity, replace the repair service starter kit.




c. Check whether or not the hold-in coil has an open circuit.
1. Using an ohmmeter, check that there is continuity between terminal 50 and the switch body.
If there is no continuity, replace the repair service starter kit.




8. INSPECT STARTER ARMATURE ASSEMBLY
a. Check the commutator for open circuit.
1. Using an ohmmeter, check that there is continuity between the segments of the commutator.
If there is no continuity between any segments, replace the starter armature.




b. Check the commutator for ground.
1. Using an ohmmeter, check that there is no continuity between the commutator and the armature coil core.
If there is continuity, replace the starter armature.

c. Check the commutator for dirty and burned surface.If the surface is dirty or burnt, correct it with sandpaper (No.400) or lathe.




d. Check the commutator depth.
1. Using vernier calipers, measure the commutator depth.
Standard length: 3.3 mm (0.1299 in.)
Maximum length: 4.0 mm (0.1575 in.)
If the depth is greater than maximum, replace the starter armature.




9. INSPECT STARTER COMMUTATOR END FRAME ASSEMBLY
a. Check the brush holder length.
1. Using vernier calipers, measure the brush holder length.
Standard length: 9.0 mm (0.354 in.)
Minimum length: 4.0 mm (0.158 in.)
If the length is less than minimum, replace the starter commutator end frame.




b. Check the brush holder.
1. Using an ohmmeter, check that there is no continuity between the positive (+) and negative (-) brush holders.
If there is continuity, repair or replace the starter commutator end frame.




10. INSPECT REPAIR SERVICE STARTER KIT
a. Check the starter clutch.
1. Rotate the clutch pinion gear counterclockwise and check that it turns freely.Try to rotate the clutch pinion gear clockwise and check that it locks.
If necessary, replace the repair service starter kit.




11. INSTALL PLANET GEAR
a. Apply grease to the planet gears and pin parts of the planetary shaft.
b. Install the 3 planet gears to the repair service starter kit.




12. INSTALL STARTER ARMATURE ASSEMBLY
a. Apply grease to the plate washer and the armature shaft.
b. Install the starter armature to the starter commutator end frame.
c. Using snap ring pliers, install the plate washer and a new snap ring.




d. Using vernier calipers, measure the snap ring.
Maximum length: 5.0 mm (0.197 in.)
If the length is greater than maximum, replace it with a new snap ring.




13. INSTALL DRIVE HOUSING STARTER BEARING COVER
a. Install the drive housing starter bearing cover to the starter commutator end frame.




14. INSTALL STARTER ARMATURE PLATE
a. Insert the starter armature plate to the starter yoke.
b. Align the keyway of the starter plate with the key inside the starter yoke, and install the starter plate.




15. INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY
a. Align the rubber with the convex cutout of starter yoke.b.Install starter commutator end frame to the starter yoke.




16. INSTALL STARTER YOKE ASSEMBLY
a. Align the key of the starter yoke with the keyway of repair service starter kit.




b. Install the starter yoke with the 2 through bolts.

Torque: 6.0 Nm (61 kgf.cm, 53 in.lbf)




17. INSTALL REPAIR SERVICE STARTER KIT
a. Apply grease to the plunger and the hook.
b. Hang the plunger hook of the repair service starter kit to the drive lever.
c. Install the plunger and the return spring.




d. Install repair service starter kit with the 2 screws.

Torque: 7.5 Nm (76 kgf.cm, 66 in.lbf)




e. Connect the lead wire to the repair service starter kit with the nut.

Torque: 6.5 Nm (66 kgf.cm, 58 in.lbf)