Operation CHARM: Car repair manuals for everyone.
Home >> Toyota >> 2006 >> Highlander 4WD V6-3.3L (3MZ-FE) >> Repair and Diagnosis >> Body and Frame >> Interior Moulding / Trim >> Headliner >> Service and Repair

Headliner: Service and Repair

ROOF HEADLINING

REMOVAL

HINT: A bolt without a torque specification is shown in the standard bolt chart.

1. REMOVE TONNEAU COVER ASSEMBLY




2. REMOVE DECK BOARD SUB-ASSEMBLY
a. Using a screwdriver, disengage the 5 clips, 2 bolts and deck board.

HINT: Tape the screwdriver tip before use.

3. REMOVE DECK BOARD SUB-ASSEMBLY NO.2
4. REMOVE DECK BOARD SUB-ASSEMBLY NO.3




5. REMOVE REAR SEAT RECLINING COVER NO.2 RH (w/ Rear No. 2 Seat)
a. Using a screwdriver, disengage the 2 clips and remove the bolt and cover.

HINT: Tape the screwdriver tip before use.

6. REMOVE REAR SEAT RECLINING COVER NO.2 LH (w/ Rear No. 2 Seat)

HINT: Use the same procedures described for the LH side.




7. REMOVE DECK FLOOR BOX REAR
a. Using a screwdriver, remove the 2 clips and box rear.

HINT: Tape the screwdriver tip before use.

8. REMOVE DECK FLOOR BOX FRONT (w/o Rear No. 2 Seat)




9. REMOVE REAR FLOOR FINISH PLATE
a. Using a screwdriver, remove the 2 clips labeled A, 4 clips labeled B and finish plate.

HINT: Tape the screwdriver tip before use.

10. REMOVE DECK SIDE TRIM BOX LH
11. REMOVE DECK SIDE TRIM BOX RH
12. REMOVE REAR NO. 1 SEAT ASSEMBLY LH (w/ Rear No. 2 Seat)
13. REMOVE REAR NO. 1 SEAT ASSEMBLY LH
14. REMOVE REAR NO. 1 SEAT ASSEMBLY RH
15. REMOVE REAR NO. 1 SEAT ASSEMBLY RH
16. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/o Rear No. 2 Seat)




17. REMOVE FRONT DOOR SCUFF PLATE LH (w/ Rear No. 2 Seat)
a. Using a screwdriver, disengage the 4 claws labeled A, 2 claws labeled B, claw labeled C and remove the scuff plate.

HINT: Tape the screwdriver tip before use.

18. REMOVE FRONT DOOR SCUFF PLATE RH (w/o Rear No. 2 Seat)

HINT: Use the same procedures described for the LH side.




19. REMOVE REAR DOOR SCUFF PLATE LH (w/ Rear No. 2 Seat)
a. Using a screwdriver, disengage the 2 claws and remove the scuff plate.

HINT: Tape the screwdriver tip before use.

20. REMOVE REAR DOOR SCUFF PLATE RH

HINT: Use the same procedures described for the LH side.


21. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
22. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
23. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
24. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
25. REMOVE BACK DOOR WEATHERSTRIP




26. REMOVE CENTER PILLAR GARNISH LOWER LH
a. Using a screwdriver, disengage the 2 claws and remove the 5 clips and garnish.

HINT: Tape the screwdriver tip before use.

27. REMOVE CENTER PILLAR GARNISH LOWER RH

HINT: Use the same procedures described for the LH side.




28. REMOVE CENTER PILLAR GARNISH LH
a. Using a screwdriver, disengage the 2 claws labeled A and 2 claws labeled B, remove the cover.

HINT: Tape the screwdriver tip before use.

b. Remove the shoulder anchor bolt.




c. Remove the 2 screws.
d. Using a screwdriver, disengage the clip and remove the garnish.

HINT: Tape the screwdriver tip before use.

29. REMOVE CENTER PILLAR GARNISH RH

HINT: Use the same procedures described for the LH side.

30. REMOVE ROPE HOOK




31. REMOVE DECK SIDE TRIM COVER LH
a. Using a screwdriver, remove the cover and screw.

HINT: Tape the screwdriver tip before use.

b. Using a screwdriver, disengage the 2 claws and remove the trim box.

HINT: Tape the screwdriver tip before use.

32. REMOVE DECK SIDE TRIM COVER RH

HINT: Use the same procedures described for the LH side.




33. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
a. w/o Rear No. 2 seat:
1. Remove the 5 bolts and rear seat outer belt floor anchor bolt.
2. Using a clip remover, remove the 6 clips and side panel.




b. w/ Rear No. 2 seat:
1. Remove the 5 bolts and rear seat outer belt floor anchor bolt.
2. Using a clip remover, remove the 6 clips and side panel.

34. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

HINT: Use the same procedures described for the LH side.




35. REMOVE QUARTER PILLAR GARNISH LH
a. Using a screwdriver, remove the clip labeled A and clip labeled B and garnish.

HINT: Tape the screwdriver tip before use.

36. REMOVE QUARTER PILLAR GARNISH RH

HINT: Use the same procedures described for the LH side.




37. REMOVE ROOF SIDE RAIL GARNISH SUB-ASSEMBLY LH
a. Using a screwdriver, disengage the 3 clips and remove the 3 claws and rail garnish.

HINT: Tape the screwdriver tip before use.

38. REMOVE ROOF SIDE RAIL GARNISH SUB-ASSEMBLY RH

HINT: Use the same procedures described for the LH side.




39. REMOVE ROOF SIDE GARNISH ASSEMBLY INNER LH
a. w/o Rear No. 2 seat:
1. Using a screwdriver, remove the 4 clips and side garnish.

HINT: Tape the screwdriver tip before use.




b. w/ Rear No. 2 seat:
1. Using a screwdriver, remove the 4 clips labeled A, clip labeled B, remove the side garnish.

HINT: Tape the screwdriver tip before use.

40. REMOVE ROOF SIDE GARNISH ASSEMBLY INNER RH

HINT: Use the same procedures described for the LH side.




41. REMOVE FRONT PILLAR GARNISH LH
a. Using a screwdriver, remove the front pillar garnish.

HINT: Tape the screwdriver tip before use.

b. Pull the garnish upward and remove it from the instrument panel.




c. w/ Curtain shield airbag:
1. Using a screwdriver, disengage the clips clip labeled A and clip labeled B.

HINT: Tape the screwdriver tip before use.

d. Remove the pillar garnish.
1. Pull the pillar garnish until the clip marked A in the illustration stretches.
2. Turn the clip marked A in the illustration 90 degrees and remove the pillar garnish.

HINT: Use the same procedures described for the LH side.




e. Protect the curtain shield airbag LH.
1. Cover the airbag with cloth or a piece of nylon approximately 700 mm (27.56 in.) x 120 mm (4.72 in.) in size. Fix the ends of the cover with tape as shown in the illustration.

NOTE: Cover the curtain shield airbag with the protective cover as soon as the front pillar garnish is removed.

42. REMOVE FRONT PILLAR GARNISH RH

HINT: Use the same procedures described for the LH side.

43. REMOVE LH VISOR ASSEMBLY
a. Remove the 2 screws and visor.

44. REMOVE RH VISOR ASSEMBLY
a. Remove the 2 screws and visor.




45. REMOVE ROOF CONSOLE BOX ASSEMBLY
a. Remove the 2 screws.
b. Using a screwdriver, remove the 2 clips.

HINT: Tape the screwdriver tip before use.




46. REMOVE ROOM LIGHT ASSEMBLY NO.1
a. Using a screwdriver, disengage the 2 claws and remove the 2 clips and light.

HINT: Tape the screwdriver tip before use.

47. REMOVE ROOM LIGHT ASSEMBLY NO.2




48. REMOVE ASSIST GRIP SUB-ASSEMBLY
a. Using a screwdriver, remove the assist grip plug.

HINT: Tape the screwdriver tip before use.

b. Remove the 2 screws and assist grip.




49. REMOVE VISOR HOLDER
a. Remove the holder of the sun visor by turning it to the left.

50. REMOVE SUN ROOF OPENING TRIM MOULDING




51. REMOVE ROOF HEADLINING ASSEMBLY
a. Using a clip remover, remove the 4 clips and roof headlining.
b. Remove the headlining from the back door.

52. REMOVE ROOF SILENCER PAD NO.4
53. REMOVE ROOF SILENCER PAD NO.1
54. REMOVE ROOF SILENCER PAD NO.5
55. REMOVE ROOF SILENCER PAD NO.2 (w/o Sliding Roof)


INSTALLATION




1. INSTALL ROOF HEADLINING ASSEMBLY
a. Align the markings, and then install the wire harness with tape.

NOTE: Attach the roof wire harness securely.

b. Install the roof headlining with the 4 clips.

2. INSTALL QUARTER PILLAR GARNISH LH
a. Install the rear No. 2 seat outer belt shoulder anchor with the bolt.

Torque: 42.0 N.m (420 kgf.cm, 31 ft.lbf)

3. INSTALL QUARTER PILLAR GARNISH RH

HINT: Use the same procedures described for the LH side.

4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
a. Install the rear seat outer belt floor anchor with the bolt.

Torque: 42.0 N.m (420 kgf.cm, 31 ft.lbf)

5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

HINT: Use the same procedures described for the LH side.

6. INSTALL CENTER PILLAR GARNISH LH
a. Install the front seat outer belt shoulder anchor with the bolt.

Torque: 42.0 N.m (420 kgf.cm, 31 ft.lbf)

7. INSTALL CENTER PILLAR GARNISH RH

HINT: Use the same procedures described for the LH side.
pro multis · About Operation CHARM