Disassembly and Reassembly
DISASSEMBLYCAUTION: Wear safety gloves, because the sharp edges and surfaces of the seat frame may cause injury to the hands.
HINT:
- The procedures listed below are for the LH side.
- Tape the screwdriver tip before using it to remove the parts.
1. REMOVE HEADREST
2. REMOVE SEAT CUSHION OUTER SHIELD
a. Remove the screw from the seat cushion outer shield.
b. Using a screwdriver, remove the seat cushion outer shield.
HINT: Tape the screwdriver tip before use.
3. REMOVE RECLINING ADJUSTER RELEASE HANDLE
4. REMOVE VERTICAL ADJUSTER HANDLE
a. Using a screwdriver, remove the vertical adjuster handle cap.
HINT: Tape the screwdriver tip before use.
b. Remove the 2 screws and the vertical adjuster handle.
5. REMOVE SEAT CUSHION INNER SHIELD
a. Remove the screw from the seat cushion inner shield.
b. Using a screwdriver, remove the seat cushion inner shield.
HINT: Tape the screwdriver tip before use.
6. REMOVE FRONT SEAT INNER BELT
a. Disconnect the wire harness clamps and connectors.
b. Remove the nut and front seat inner belt.
7. REMOVE ARMREST ASSEMBLY
a. Using a screwdriver, remove the armrest cap.
b. Remove the bolt, armrest spacer, armrest lock plate and armrest assembly.
c. Remove the spacer from the armrest assembly.
8. REMOVE SEATBACK COVER AND PAD
a. Remove the hog rings from the seat frame assembly.
b. Open the fastener.
c. with Side airbag:
Remove the nut and disconnect the seatback cover bracket from the seat frame assembly.
d. Remove the hog rings shown in the illustration from the seat frame assembly.
e. Remove the hog rings shown in the illustration from the seat frame assembly.
f. Remove the seatback cover and pad from the seat frame assembly.
g. Turn up the seatback cover and remove the hog rings.
h. Remove the 2 headrest supports.
i. Remove the seatback cover from the seatback pad.
9. REMOVE SEAT CUSHION COVER AND PAD
a. Remove the clip.
b. Perform the same procedure on the other side.
c. Remove the hog rings from the seat cushion cover.
d. Unlatch the seat cushion cover hooks, then remove the seat cushion cover with seat cushion pad.
e. Remove the hog rings and seat cushion cover from the seat cushion pad.
10. REMOVE RH AND LH UPPER RECLINING ADJUSTER INSIDE COVER
a. Remove the screw and upper reclining adjuster inside cover.
b. Perform the same procedure on the other side.
11. REMOVE RH AND LH LOWER RECLINING ADJUSTER INSIDE COVER
a. Remove the screw and lower reclining adjuster inside cover.
b. Perform the same procedure on the other side.
12. REMOVE RH AND LH SEAT CUSHION LOWER SHIELD
a. Using a screwdriver, disengage the claw and remove the seat cushion lower shield.
HINT: Tape the screwdriver tip before use.
b. Perform the same procedure on the other side.
13. REMOVE SEAT POSITION SENSOR (for Driver Seat)
REASSEMBLY
CAUTION: Wear safety gloves, because the sharp edges and surfaces of the seat frame may cause injury to the hands.
HINT: A bolt without a torque specification is shown in the standard bolt chart.
1. INSTALL SEAT POSITION SENSOR (for Driver Side)
2. INSTALL RH AND LH SEAT CUSHION LOWER SHIELD
3. INSTALL RH AND LH LOWER RECLINING ADJUSTER INSIDE COVER
a. Install the lower reclining adjuster inside cover with the screw.
b. Perform the same procedure on the other side.
4. INSTALL RH AND LH UPPER RECLINING ADJUSTER INSIDE COVER
a. Install the upper reclining adjuster inside cover with the screw.
b. Perform the same procedure on the other side.
5. INSTALL SEAT CUSHION COVER AND PAD
a. Install the seat cushion cover to the seat cushion pad with the hog rings.
HINT: When installing the hog rings, take as much care as possible to prevent wrinkles.
b. Install the seat cushion cover with seat cushion pad, and latch the seat cushion cover hooks.
c. Install the hog rings to the seat cushion cover.
d. Install the clip.
e. Perform the same procedure on the other side.
6. INSTALL SEATBACK COVER AND PAD
a. Install the seatback cover to the seatback pad.
b. Install the 2 headrest supports.
c. Turn up the seatback cover and install the hog rings
d. Install the seatback cover and pad to the seat frame assembly.
e. Install the hog rings to the seat frame assembly.
f. Install the hog rings to the seat frame assembly.
g. with Side airbag:
Connect the seatback cover bracket to the seat frame assembly with the nut.
Torque: 5.5 N.m (56 kgf.cm, 49 in.lbf)
h. Close the fastener.
i. Install the hog rings to the seat frame assembly.
7. INSTALL ARMREST ASSEMBLY
a. Install the spacer to the armrest assembly.
b. Install the armrest assembly, armrest lock plate and armrest spacer with the bolt.
Torque: 37 N.m (380 kgf.cm, 27 ft.lbf)
HINT: Install the armrest lock plate as shown in the illustration.
c. Install the armrest cap.
8. INSTALL FRONT SEAT INNER BELT
a. Install the front seat inner belt with the nut.
Torque: 42 N.m (430 kgf.cm, 32 ft.lbf)
b. Connect the connectors and wire harness clamps.
9. INSTALL SEAT CUSHION INNER SHIELD
a. Install the seat cushion inner shield with the screw.
10. INSTALL VERTICAL ADJUSTER HANDLE
a. Install the vertical adjuster handle with the 2 screws.
b. Install the vertical adjuster handle cap.
11. INSTALL RECLINING ADJUSTER RELEASE HANDLE
12. INSTALL SEAT CUSHION OUTER SHIELD
a. Install the seat cushion outer shield with the screw.
13. INSTALL HEADREST