Trunk / Liftgate Spring: Service and Repair
LUGGAGE DOOR HINGE TORSION BARLuggage Door Hinge Torsion Bar:
REMOVAL
1. REMOVE LUGGAGE COMPARTMENT FLOOR MAT
2. REMOVE SPARE WHEEL COVER CLAMP
3. REMOVE SPARE WHEEL COVER ASSEMBLY
4. REMOVE LUGGAGE COMPARTMENT SIDE TRAY ASSEMBLY
a. Remove the bolt.
b. Disengage the clip and remove the luggage compartment side tray assembly.
5. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
a. Remove the 2 screws and the 2 No. 1 luggage compartment trim hooks.
6. REMOVE REAR FLOOR FINISH PLATE
a. Disengage the 7 clips and remove the rear floor finish plate.
7. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH
a. Remove the 2 clips and the luggage compartment inner trim cover LH.
8. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER RH
a. Remove the 2 clips and the luggage compartment inner trim cover RH.
9. REMOVE LUGGAGE DOOR HINGE TORSION BAR RH
a. Disconnect the luggage door hinge torsion bar RH from the luggage compartment door torsion bar support as shown in the illustration.
b. Using SST, disconnect the luggage door hinge torsion bar RH from the luggage door hinge and the right side of the vehicle body as shown in the illustration.
SST 09804-24010
c. Remove the luggage door hinge torsion bar RH from the left side of the vehicle body as shown in the illustration.
10. REMOVE LUGGAGE DOOR HINGE TORSION BAR LH
a. Disconnect the luggage door hinge torsion bar LH from the luggage compartment door torsion bar support as shown in the illustration.
b. Using SST, disconnect the luggage door hinge torsion bar LH from the luggage door hinge and the left side of the vehicle body as shown in the illustration.
SST 09804-24010
c. Remove the luggage door hinge torsion bar LH from the right side of the vehicle body as shown in the illustration.
11. REMOVE LUGGAGE COMPARTMENT DOOR TORSION BAR SUPPORT
a. Remove the luggage compartment door torsion bar support as shown in the illustration.
INSTALLATION
HINT: After installing the torsion bar, use your hand to open and close the luggage door. Make sure the luggage door can open and close smoothly.
1. INSTALL LUGGAGE COMPARTMENT DOOR TORSION BAR SUPPORT
a. Install the luggage compartment door torsion bar support as shown in the illustration.
2. INSTALL LUGGAGE DOOR HINGE TORSION BAR LH
a. Set the tip of the luggage door hinge torsion bar LH in the center installation hole. The upper and lower installation holes are used for adjustment.
b. Connect the luggage door hinge torsion bar LH to the right side of the vehicle body as shown in the illustration.
c. Connect the luggage door hinge torsion bar LH to the luggage compartment door torsion bar support as shown in the illustration.
d. Using SST, install the luggage door hinge torsion bar LH to the luggage door hinge and the left side of the vehicle body as shown in the illustration.
SST 09804-24010
3. INSTALL LUGGAGE DOOR HINGE TORSION BAR RH
a. Set the tip of the luggage door hinge torsion bar RH in the center installation hole. The upper and lower installation holes are used for adjustment.
b. Connect the luggage door hinge torsion bar RH to the left side of the vehicle body as shown in the illustration.
c. Connect the luggage door hinge torsion bar RH to the luggage compartment door torsion bar support as shown in the illustration.
d. Using SST, install the luggage door hinge torsion bar RH to the luggage door hinge and the right side of the vehicle body as shown in the illustration.
SST 09804-24010
4. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER LH
a. Install the luggage compartment inner trim cover LH with the 2 clips.
5. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER RH
a. Install the luggage compartment inner trim cover RH with the 2 clips.
6. INSTALL REAR FLOOR FINISH PLATE
a. Engage the 7 clips and install the rear floor finish plate.
7. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
a. Install the 2 No. 1 luggage compartment trim hooks with the 2 screws.
8. INSTALL LUGGAGE COMPARTMENT SIDE TRAY ASSEMBLY
a. Engage the clip and install the luggage compartment side tray assembly.
b. Install the bolt.
9. INSTALL SPARE WHEEL COVER ASSEMBLY
10. INSTALL SPARE WHEEL COVER CLAMP
11. INSTALL LUGGAGE COMPARTMENT FLOOR MAT