Front Door Lock (For Hatchback)

Front Door Lock (for Hatchback):

Front Door Lock (for Hatchback):

Front Door Lock (for Hatchback):

FRONT DOOR LOCK (for Hatchback)

REMOVAL

HINT:
- Use the same procedure for both the RH and LH sides.
- The procedure listed below is for the LH side.

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

3. REMOVE DOOR ARMREST COVER

4. REMOVE FRONT ARMREST BASE PANEL UPPER

5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

6. REMOVE FRONT DOOR WINDOW FRAME FRONT MOULDING

7. REMOVE FRONT DOOR WINDOW FRAME REAR MOULDING (for 3 Door)

8. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

9. REMOVE FRONT DOOR BELT MOULDING

10. REMOVE FRONT DOOR SERVICE HOLE COVER

11. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

12. REMOVE FRONT DOOR GLASS RUN

13. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/ Power Window)

14. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/o Power Window)

15. REMOVE FRONT DOOR CHECK ASSEMBLY

16. REMOVE FRONT DOOR WEATHERSTRIP

17. REMOVE FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER

18. REMOVE FRONT DOOR OUTSIDE HANDLE COVER




19. REMOVE FRONT DOOR LOCK ASSEMBLY
a. Using "Torx" socket wrench T30, loosen the 3 screws.
b. Move the front door lock downward, remove the outside handle frame link and remove the front door lock.




c. Disengage the 5 claws and open the cover.




d. Disconnect the front door lock remote control cable and the front door inside locking cable.
e. Remove the door lock wire harness seal.


INSTALLATION

1. INSTALL FRONT DOOR LOCK ASSEMBLY

NOTE:
- If reusing a door lock that has been removed, replace the packing in the connecting part with new.
- Make sure that no grease and dirt adheres to the packing surface in the connecting part.

a. Apply MP grease to the sliding and rotating areas of the front door lock.




b. Connect the front door lock remote control cable and the front door inside locking cable.




c. Engage the 5 claws and close the cover.




d. Insert the door lock open rod into the front door lock, then set it to the door panel.

NOTE: Make sure that the outside handle link is securely engaged with the door lock.




e. Apply adhesive to the threads of the screws.

Adhesive: Part No. 08833-00070, THREE BOND 1324 or the equivalent

f. Using "Torx" socket wrench T30, install the front door lock with the 3 screws.

Torque: 5.0 N.m (51 kgf.cm, 44 in.lbf)

2. INSTALL FRONT DOOR OUTSIDE HANDLE COVER

3. INSTALL FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER

4. INSTALL FRONT DOOR WEATHERSTRIP

5. INSTALL FRONT DOOR CHECK ASSEMBLY

6. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/ Power Window)

7. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/o Power Window)

8. INSTALL FRONT DOOR GLASS RUN

9. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

10. INSTALL FRONT DOOR SERVICE HOLE COVER

11. INSTALL FRONT DOOR BELT MOULDING

12. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

13. INSTALL FRONT DOOR WINDOW FRAME REAR MOULDING (for 3 Door)

14. INSTALL FRONT DOOR WINDOW FRAME FRONT MOULDING

15. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

16. INSTALL FRONT ARMREST BASE PANEL UPPER

17. INSTALL DOOR ARMREST COVER

18. INSTALL DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque: 5.4 N.m (55 kgf.cm, 48 in.lbf)